Studying the Effect of Light Incidence Angle on Photoelectric Parameters of Solar Cells by Simulation

It is crucial to examine the dependence of photoelectric parameters of solar cells on the light incidence angle. In the present study, two solar cell models have been developed using the Sentaurus Technology Computer-Aided Design software package. The light spectrum AM1.5 has been directed on the frontal surface of solar cells at different angles. It has been found that the angular coefficient of the photoelectric parameters of a solar cell with nanoparticles included, is two times more than that of a simple solar cell. Besides, it has been found that the efficiency of platinum nanoparticles induced solar cells is 2.15 times greater than simple solar cell efficiency. When the light incidence angle has been varied from 0 to 60 degrees, the short-circuit current has changed by 11% for simple solar cells and by 10% for solar cells with nanoparticles. Further, it has been observed that the variation of power for simple solar cells is 12.5%, while it is 10.5% for solar cells with nanoparticles. In addition, the short-circuit current of solar cells with nanoparticles has been found to be linear within a light incidence angle ranging from 0 to 60 degrees.

Download Full-text

CdTe-Based Thin Film Solar Cells: Past, Present and Future

Energies ◽

10.3390/en14061684 ◽

2021 ◽

Vol 14 (6) ◽

pp. 1684

Author(s):

Alessandro Romeo ◽

Elisa Artegiani

Keyword(s):

Thin Film ◽

Solar Cells ◽

Solar Cell ◽

Short Circuit ◽

Short Circuit Current ◽

Short Circuit Current Density ◽

Open Circuit ◽

Early Years ◽

Solar Cell Efficiency ◽

Cell Efficiency

CdTe is a very robust and chemically stable material and for this reason its related solar cell thin film photovoltaic technology is now the only thin film technology in the first 10 top producers in the world. CdTe has an optimum band gap for the Schockley-Queisser limit and could deliver very high efficiencies as single junction device of more than 32%, with an open circuit voltage of 1 V and a short circuit current density exceeding 30 mA/cm2. CdTe solar cells were introduced at the beginning of the 70s and they have been studied and implemented particularly in the last 30 years. The strong improvement in efficiency in the last 5 years was obtained by a new redesign of the CdTe solar cell device reaching a single solar cell efficiency of 22.1% and a module efficiency of 19%. In this paper we describe the fabrication process following the history of the solar cell as it was developed in the early years up to the latest development and changes. Moreover the paper also presents future possible alternative absorbers and discusses the only apparently controversial environmental impacts of this fantastic technology.

Download Full-text

GaInP/GaAs/poly-Si Multi-Junction Solar Cells by in Metal Balls Bonding

Crystals ◽

10.3390/cryst11070726 ◽

2021 ◽

Vol 11 (7) ◽

pp. 726

Author(s):

Ray-Hua Horng ◽

Yu-Cheng Kao ◽

Apoorva Sood ◽

Po-Liang Liu ◽

Wei-Cheng Wang ◽

...

Keyword(s):

Solar Cells ◽

Solar Cell ◽

Low Temperature ◽

Triple Junction ◽

Short Circuit ◽

Short Circuit Current ◽

Open Circuit ◽

Metal Line ◽

Solar Simulator ◽

Junction Solar Cell

In this study, a mechanical stacking technique has been used to bond together the GaInP/GaAs and poly-silicon (Si) solar wafers. A GaInP/GaAs/poly-Si triple-junction solar cell has mechanically stacked using a low-temperature bonding process which involves micro metal In balls on a metal line using a high-optical-transmission spin-coated glue material. Current–voltage measurements of the GaInP/GaAs/poly-Si triple-junction solar cells have carried out at room temperature both in the dark and under 1 sun with 100 mW/cm2 power density using a solar simulator. The GaInP/GaAs/poly-Si triple-junction solar cell has reached an efficiency of 24.5% with an open-circuit voltage of 2.68 V, a short-circuit current density of 12.39 mA/cm2, and a fill-factor of 73.8%. This study demonstrates a great potential for the low-temperature micro-metal-ball mechanical stacking technique to achieve high conversion efficiency for solar cells with three or more junctions.

Download Full-text

Study of Photoelectrochemical Solar Cell Using WSe2 Crystal

Advanced Materials Research ◽

10.4028/www.scientific.net/amr.665.330 ◽

2013 ◽

Vol 665 ◽

pp. 330-335 ◽

Cited By ~ 1

Author(s):

Ripal Parmar ◽

Dipak Sahay ◽

R.J. Pathak ◽

R.K. Shah

Keyword(s):

Solar Cells ◽

Solar Cell ◽

Fill Factor ◽

Short Circuit ◽

Short Circuit Current ◽

Electrical Energy ◽

Open Circuit ◽

Cell Parameters ◽

Photoelectrochemical Solar Cell ◽

Photoelectrochemical Solar Cells

The solar cells have been used as most promising device to convert light energy into electrical energy. In this paper authors have attempted to fabricate Photoelectrochemical solar cell with semiconductor electrode using TMDCs. The Photoelectrochemical solar cells are the solar cells which convert the solar energy into electrical energy. The photoelectrochemical cells are clean and inexhaustible sources of energy. The photoelectrochemical solar cells are fabricated using WSe2crystal and electrolyte solution of 0.025M I2, 0.5M NaI, 0.5M Na2SO4. Here the WSe2crystals were grown by direct vapour transport technique. In our investigations the solar cell parameters like short circuit current (Isc) and Open circuit voltage (Voc) were measured and from that Fill factor (F.F.) and photoconversion efficiency (η) are investigated. The results obtained shows that the value of efficiency and fill factor of solar cell varies with the illumination intensities.

Download Full-text

Numerical Simulation of Single Junction InGaN Solar Cell by SCAPS

Key Engineering Materials ◽

10.4028/www.scientific.net/kem.821.407 ◽

2019 ◽

Vol 821 ◽

pp. 407-413 ◽

Cited By ~ 2

Author(s):

Mohamed Orabi Moustafa ◽

Tariq Alzoubi

Keyword(s):

Solar Cells ◽

Solar Cell ◽

Collection Efficiency ◽

Short Circuit ◽

Photovoltaic Performance ◽

Surface Recombination ◽

Short Circuit Current ◽

Short Circuit Current Density ◽

Bandgap Energy ◽

Single Junction

The performance of the InGaN single-junction thin film solar cells has been analyzed numerically employing the Solar Cell Capacitance Simulator (SCAPS-1D). The electrical properties and the photovoltaic performance of the InGaN solar cells were studied by changing the doping concentrations and the bandgap energy along with each layer, i.e. n-and p-InGaN layers. The results reveal an optimum efficiency of the InGaN solar cell of ~ 15.32 % at a band gap value of 1.32 eV. It has been observed that lowering the doping concentration NA leads to an improvement of the short circuit current density (Jsc) (34 mA/cm2 at NA of 1016 cm−3). This might be attributed to the increase of the carrier mobility and hence an enhancement in the minority carrier diffusion length leading to a better collection efficiency. Additionally, the results show that increasing the front layer thickness of the InGaN leads to an increase in the Jsc and to the conversion efficiency (η). This has been referred to the increase in the photogenerated current, as well as to the less surface recombination rate.

Download Full-text

Analytical Study of the Electrical Output Characteristics of c-Si Solar Cells by Cut and Shading Phenomena

Energies ◽

10.3390/en11123397 ◽

2018 ◽

Vol 11 (12) ◽

pp. 3397 ◽

Cited By ~ 1

Author(s):

Jong Lim ◽

Woo Shin ◽

Hyemi Hwang ◽

Young-Chul Ju ◽

Suk Ko ◽

...

Keyword(s):

Solar Cells ◽

Solar Cell ◽

Crystalline Silicon ◽

Short Circuit ◽

Incident Light ◽

Short Circuit Current ◽

Open Circuit ◽

Si Solar Cell ◽

Si Solar Cells ◽

Electrical Output

Cut solar cells have received considerable attention recently as they can reduce electrical output degradation when the c-Si solar cells (crystalline-silicon solar cells) are shaded. Cut c-Si solar cells have a lower short-circuit current than normal solar cells and the decrease in short-circuit currents is similar to the shading effect of c-Si solar cells. However, the results of this study’s experiment show that the shadow effect of a c-Si solar cell reduces the V o c (open circuit voltage) in the c-Si solar cell but the V o c does not change when the c-Si solar cell is cut because the amount of incident light does not change. In this paper, the limitations of the electrical power analysis of the cut solar cells were identified when only photo current was considered and the analysis of the electric output of the cut c-Si solar cells was interpreted with a method different from that used in previous analyses. Electrical output was measured when the shaded and cut rates of c-Si solar cells were increased from 0% to 25, 50 and 75%, and a new theoretical model was compared with the experimental results using MATLAB.

Download Full-text

Dye-sensitized solar cells with natural dyes extracted from plant seeds

Materials Science-Poland ◽

10.2478/s13536-014-0231-z ◽

2014 ◽

Vol 32 (4) ◽

pp. 547-554 ◽

Cited By ~ 14

Author(s):

Hatem El-Ghamri ◽

Taher El-Agez ◽

Sofyan Taya ◽

Monzir Abdel-Latif ◽

Amal Batniji

Keyword(s):

Solar Cells ◽

Solar Cell ◽

Tio2 Film ◽

Short Circuit ◽

Dye Sensitized Solar Cells ◽

Short Circuit Current ◽

Natural Dyes ◽

Plant Seeds ◽

Dye Sensitized ◽

Sensitized Solar Cells

AbstractThe application of natural dyes extracted from plant seeds in the fabrication of dye-sensitized solar cells (DSSCs) has been explored. Ten dyes were extracted from different plant seeds and used as sensitizers for DSSCs. The dyes were characterized using UV-Vis spectrophotometry. DSSCs were prepared using TiO2 and ZnO nanostructured mesoporous films. The highest conversion efficiency of 0.875 % was obtained with an allium cepa (onion) extract-sensitized TiO2 solar cell. The process of TiO2-film sintering was studied and it was found that the sintering procedure significantly affects the response of the cell. The short circuit current of the DSSC was found to be considerably enhanced when the TiO2 semiconducting layer was sintered gradually.

Download Full-text

Donor-π-Conjugated Spacer-Acceptor Dye-Sensitized Solid-State Solar Cell Using CuI as the Hole Collector

International Journal of Photoenergy ◽

10.1155/2019/1653027 ◽

2019 ◽

Vol 2019 ◽

pp. 1-5

Author(s):

D. N. Liyanage ◽

K. D. M. S. P. K. Kumarasinghe ◽

G. R. A. Kumara ◽

A. C. A. Jayasundera ◽

K. Tennakone ◽

...

Keyword(s):

Solar Cells ◽

Solar Cell ◽

Solid State ◽

Short Circuit ◽

Electrical Power ◽

Short Circuit Current ◽

Liquid Electrolyte ◽

Short Circuit Current Density ◽

Dye Sensitized ◽

Type Semiconductor

Dye-sensitized solid-state solar cells (DSSCs) replacing the liquid electrolyte with a p-type semiconductor have been extensively examined to solve the practical problems associated with wet-type solar cells. Here, we report the fabrication of a solid-state solar cell using copper iodide (CuI) as the hole conductor and alkyl-functionalized carbazole dye (MK-2) as the sensitizer. A DSSC sensitized with MK-2 showed a solar-to-electrical power conversion efficiency of 3.33% with a Voc of 496 mV and a Jsc of 16.14 mA cm-2 under AM 1.5 simulated sunlight. The long alkyl chains act as a barrier for charge recombination, and the strong accepting and donating abilities of the cyanoacrylic and carbazole groups, respectively, enhance the absorption of light at a longer wavelength, increasing the short-circuit current density. The efficiency recorded in this work is higher than similar DSSCs based on other hole collectors.

Download Full-text

Preparation of the Three Main Layers of CdS/CdTe Thin Film Solar Cells Using a Single Vacuum System

Advanced Materials Research ◽

10.4028/www.scientific.net/amr.378-379.601 ◽

2011 ◽

Vol 378-379 ◽

pp. 601-605 ◽

Cited By ~ 1

Author(s):

Saleh N. Alamri ◽

M. S. Benghanem ◽

A. A. Joraid

Keyword(s):

Thin Film ◽

Solar Cells ◽

Solar Cell ◽

Short Circuit ◽

Short Circuit Current ◽

Short Circuit Current Density ◽

Open Circuit ◽

Fused Silica ◽

Vacuum System ◽

Cdte Thin Film

This study investigates the preparation of the three main layers of a CdS/CdTe thin film solar cell using a single vacuum system. A Close Space Sublimation System was constructed to deposit CdS, CdTe and CdCl2 solar cell layers. Two hot plates were used to heat the source and the substrate. Three fused silica melting dishes were used as containers for the sources. The properties of the deposited CdS and CdTe films were determined via Atomic force microscopy, scanning electron microscopy, X-ray diffraction and optical transmission spectroscopy. An J-V characterization of the fabricated CdS/CdTe solar cells was performed under solar radiation. The short-circuit current density, Jsc, the open-circuit voltage, Voc, fill factor, FF and conversion efficiency, η, were measured and yielded values of 27 mA/cm2, 0.619 V, 58% and 9.8%, respectively.

Download Full-text

Improvement of short circuit current of mono crystalline silicon solar cells

Science and Technology Development Journal ◽

10.32508/stdj.v16i1.1418 ◽

2013 ◽

Vol 16 (1) ◽

pp. 48-56

Author(s):

Vu Ngoc Hoang ◽

Linh Ngoc Tran ◽

Lan Truong ◽

Khoa Thanh Nhat Phan ◽

Chien Mau Dang ◽

...

Keyword(s):

Solar Cells ◽

Solar Cell ◽

Indium Tin Oxide ◽

Crystalline Silicon ◽

Short Circuit ◽

Front Surface ◽

Short Circuit Current ◽

Open Circuit ◽

Crystalline Silicon Solar Cell ◽

Antireflection Coatings

In this report we present series of experiments during which the short circuit current of mono crystalline silicon solar cell was improved step by step so as a consequence the efficiency was increased. At first, the front contact of solar cell was optimized to reduce the shadow loss and the series resistance. Then surface treatments were prepared by TMAH solution to reduce the total light reflectance and to improve the light trapping effect. Finally, antireflection coatings were deposited to passivate the front surface either by silicon nitride thin layer or to increase the collection probability by indium tin oxide layer, and to reduce the reflectance of light. As a result, solar cells of about 13% have been obtained, with the average open circuit voltage Voc about 527mV, with the fill factor about 68% and the short circuit current about 7.92 mA/cm2 under the irradiation density of 21 mW/cm2.

Download Full-text

Novel Photonic Crystal Based Polycrystalline CdTe/Silicon Solar Cells

SRPH Journal of Fundamental Sciences and Technology ◽

10.47176/sjfst.3.1.5 ◽

2020 ◽

Keyword(s):

Solar Cells ◽

Solar Cell ◽

Photonic Crystal ◽

Conversion Efficiency ◽

Current Density ◽

Cell Structure ◽

Short Circuit ◽

Short Circuit Current ◽

Short Circuit Current Density ◽

Silicon Solar Cells

In this paper, a novel photonic crystal (PhC) polycrystalline CdTe/Silicon solar cells are theoretically explained that increase their short circuit current density and conversion efficiency. The proposed structure consist of a polycrystalline CdTe/Silicon solar cell that a photonic crystal is formed in the upper cell. The optical confinement is achieved by means of photonic crystal that can adjust the propagation and distribution of photons in solar cells. For validation of modeling, the electrical properties of the experimentally-fabricated based CdS/CdTe solar cell is modeled and compared that there is good agreement between the modeling results and experimental results from the litterature. The results of this study showed that the solar cell efficiency is increased by about 25% compared to the reference cell by using photonic crystal. The open circuit voltage, short circuit current density, fill factor and conversion efficiency of proposed solar cell structure are 1.01 V, 40.7 mA/cm2, 0.95 and 27% under global AM 1.5 conditions, respectively. Furthermore, the influence of carrier lifetime variation in the absorber layer of proposed solar cell on the electrical characteristics was theoretically considered and investigated.

Download Full-text