scholarly journals Performance evaluation of common rail direct injection (CRDI) engine fuelled with Uppage Oil Methyl Ester (UOME)

2015 ◽  
Vol 4 (1) ◽  
pp. 1-10 ◽  
Author(s):  
D.N. Basavarajappa ◽  
N. R. Banapurmath ◽  
S.V. Khandal ◽  
G. Manavendra
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Diesel Engines ◽  
High Speed ◽  
Alternative Fuels ◽  
High Pressures ◽  
Fuel Injection ◽  
Injection Timing ◽  
Engine Operation ◽  
Performance And Emission

For economic and social development of any country energy is one of the most essential requirements. Continuously increasing price of crude petroleum fuels in the present days coupled with alarming emissions and stringent emission regulations has led to growing attention towards use of alternative fuels like vegetable oils, alcoholic and gaseous fuels for diesel engine applications. Use of such fuels can ease the burden on the economy by curtailing the fuel imports. Diesel engines are highly efficient and the main problems associated with them is their high smoke and NOx emissions.  Hence there is an urgent need to promote the use of alternative fuels in place of high speed diesel (HSD) as substitute. India has a large agriculture base that can be used as a feed stock to obtain newer fuel which is renewable and sustainable. Accordingly Uppage oil methyl ester (UOME) biodiesel was selected as an alternative fuel. Use of biodiesels in diesel engines fitted with mechanical fuel injection systems has limitation on the injector opening pressure (300 bar). CRDI system can overcome this drawback by injecting fuel at very high pressures (1500-2500 bar) and is most suitable for biodiesel fuels which are high viscous. This paper presents the performance and emission characteristics of a CRDI diesel engine fuelled with UOME biodiesel at different injection timings and injection pressures. From the experimental evidence it was revealed that UOME biodiesel yielded overall better performance with reduced emissions at retarded injection timing of -10° BTDC in CRDI mode of engine operation.

Influence of Fuel Injection Timing on the Performance and Emission Characteristics of a Diesel Engine Fueled with Jatropha Methyl Ester-Tyre Pyrolysis Oil Blend

2014 ◽  
Vol 592-594 ◽  
pp. 1627-1631 ◽  
Author(s):  
Abhishek Sharma ◽  
S. Murugan
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Fuel Injection ◽  
Carbon Dioxide Emission ◽  
Early Investigation ◽  
Injection Timing ◽  
Emission Characteristics ◽  
Pyrolysis Oil ◽  
Performance And Emission ◽  
Full Load

Early investigation on utilization of Jatropha methyl ester (JME) tyre pyrolysis oil (TPO) blends in a single cylinder, constant speed, direct injection diesel engine revealed that a blend of 80% JME and 20% TPO referred to as JMETPO20 blend give a better performance and lower emissions compared to other Jatropha methyl ester tyre pyrolysis oil (JMETPO) blends. In this study, for further improvement on performance and emission characteristics, and also to find optimum injection timing for blend, experiments have been carried out with varying the injection timing. Tests have been conducted under two advanced and two reratarded injection timings in addition to the original injection timing of 23 °CA bTDC. The experimental test results showed that for the JMETPO20 blend at advanced injection timing of 24.5 °CA the brake thermal efficiency increased by about 2.21%, compared to the result of original injection timing at full load. For the JMETPO20 blend at advanced injection timing of 24.5 °CA the nitric oxide and carbon dioxide emission increased by about 4.56% and 11.91% respectively at full load, and the carbon monoxide emission decreased by about 11.21%, compared to that of original injection timing.

Characteristics of injection of diesel fuel, rapeseed oil and their mixtures in diesel engines of various types

2021 ◽  
pp. 167-178
Author(s):  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Diesel Engines ◽  
Rapeseed Oil ◽  
High Speed ◽  
Fuel Injection ◽  
Experimental Studies ◽  
Fuel Injector ◽  
High Speed Diesel ◽  
Engine Type

The necessity of adapting diesel engines to work on vegetable oils is justified. The possibility of using rapeseed oil and its mixtures with petroleum diesel fuel as motor fuels is considered. Experimental studies of fuel injection of small high-speed diesel engine type MD-6 (1 Ch 8,0/7,5)when using diesel oil and rapeseed oil and computational studies of auto-tractor diesel engine type D-245.12 (1 ChN 11/12,5), working on blends of petroleum diesel fuel and rapeseed oil. When switching autotractor diesel engine from diesel fuel to rapeseed oil in the full-fuel mode, the mass cycle fuel supply increased by 12 %, and in the small-size high-speed diesel engine – by about 27 %. From the point of view of the flow of the working process of these diesel engines, changes in other parameters of the fuel injection process are less significant. Keywords diesel engine; petroleum diesel fuel; vegetable oil; rapeseed oil; high pressure fuel pump; fuel injector; sprayer

Influence of Injection Pressure on Performance and Emission Characteristics of Nerium Methyl Ester Operated DI Diesel Engine

2014 ◽  
Vol 592-594 ◽  
pp. 1632-1637
Author(s):  
Ramalingam Senthil ◽  
C. Paramasivam ◽  
Rajendran Silambarasan
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Fuel Injection ◽  
Cetane Number ◽  
Load Condition ◽  
Injection Pressure ◽  
Emission Characteristics ◽  
Operational Parameters ◽  
Performance And Emission ◽  
Standard Design

Nerium methyl ester, an esterified biofuel, has an excellent cetane number and a reasonable calorific value. It closely resembles the behaviour of diesel. However, being a fuel of different origin, the standard design limits of a diesel engine is not suitable for Nerium methyl ester (NME). Therefore, in this work, a set of design and operational parameters are studied to find out the optimum performance of Nerium methyl ester run diesel engine. This work targets at finding the effects of the engine design parameter viz. fuel injection pressure (IP) on the performance with regard to specific fuel consumption (SFC), brake thermal efficiency (BTHE) and emissions of CO, CO2, HC, NOxwith N20 as fuel. Comparison of performance and emission was done for different values of injection pressure to find best possible condition for operating engine with NME. For small sized direct injection constant speed engines used for agricultural applications, the optimum injection pressure was found as 240bar.Methyl esters from Nerium, with properties close to diesel; show better performance and emission characteristics. Hence Nerium (N20) blend can be used in existing diesel engines without compromising the engine performance. Diesel (25%) thus saved will greatly help the interests of railways in meeting the demand for fuel,as diesel trains are operated at maximum load condition.

Scaling liquid penetration in evaporating sprays for different size diesel engines

2019 ◽  
Vol 21 (9) ◽  
pp. 1662-1677 ◽  
Author(s):  
Xinyi Zhou ◽  
Tie Li ◽  
Yijie Wei ◽  
Ning Wang
Keyword(s):  
Diesel Engine ◽  
Diesel Engines ◽  
High Speed ◽  
Scaling Laws ◽  
Fuel Injection ◽  
Pollutant Emissions ◽  
Liquid Penetration ◽  
Spray Characteristics ◽  
Penetration Length ◽  
Air Mixing

Scaled model experiments can greatly reduce the cost, time and energy consumption in diesel engine development, and the similarity of spray characteristics has a primary effect on the overall scaling results of engine performance and pollutant emissions. However, although so far the similarity of spray characteristics under the non-evaporating condition has been studied to some extent, researches on scaling the evaporating sprays are still absent. The maximum liquid penetration length has a close relationship with the spray evaporation processes and is a key parameter in the design of diesel engine spray combustion system. In this article, the similarity of maximum liquid penetration length is theoretically derived based on the hypotheses that the spray evaporation processes in modern high-pressure common rail diesel engines are fuel–air mixing controlled and local interphase transport controlled, respectively. After verifying that the fuel injection rates are perfectly scaled, the similarity of maximum liquid penetration length in evaporating sprays is studied for three scaling laws using two nozzles with hole diameter of 0.11 and 0.14 mm through the high-speed diffused back-illumination method. Under the test conditions of different fuel injection pressures, ambient temperatures and densities, the lift-off law and speed law lead to a slightly increased maximum liquid penetration length, while the pressure law can well scale the maximum liquid penetration length. The experimental results are consistent with the theoretical analyses based on the hypothesis that the spray evaporation processes are fuel–air mixing controlled, indicating that the local interphase transports of energy, momentum and mass on droplet surface are not rate-controlled steps with respect to spray evaporation processes.

Experimental investigations on combustion of jatropha methyl ester in a turbocharged direct-injection diesel engine

2008 ◽  
Vol 222 (10) ◽  
pp. 1865-1877 ◽  
Author(s):  
K Anand ◽  
R P Sharma ◽  
P S Mehta
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Peak Pressure ◽  
Direct Injection ◽  
Pressure Rise ◽  
Experimental Investigations ◽  
Injection Timing ◽  
Gas Temperature

Suitability of vegetable oil as an alternative to diesel fuel in compression ignition engines has become attractive, and research in this area has gained momentum because of concerns on energy security, high oil prices, and increased emphasis on clean environment. The experimental work reported here has been carried out on a turbocharged direct-injection multicylinder truck diesel engine using diesel fuel and jatropha methyl ester (JME)-diesel blends. The results of the experimental investigation indicate that an increase in JME quantity in the blend slightly advances the dynamic fuel injection timing and lowers the ignition delay compared with the diesel fuel. A maximum rise in peak pressure limited to 6.5 per cent is observed for fuel blends up to 40 per cent JME for part-load (up to about 50 per cent load) operations. However, for a higher-JME blend, the peak pressures decrease at higher loads remained within 4.5 per cent. With increasing proportion of JME in the blend, the peak pressure occurrence slightly advances and the maximum rate of pressure rise, combustion duration, and exhaust gas temperature decrease by 9 per cent, 15 per cent and 17 per cent respectively. Although the changes in brake thermal efficiencies for 20 per cent and 40 per cent JME blends compared with diesel fuel remain insignificant, the 60 per cent JME blend showed about 2.7 per cent improvement in the brake thermal efficiency. In general, it is observed that the overall performance and combustion characteristics of the engine do not alter significantly for 20 per cent and 40 per cent JME blends but show an improvement over diesel performance when fuelled with 60 per cent JME blend.

Effect of Injection System Parameters on Performance and Emission Characteristics of a Small Single Cylinder Diesel Engine

2021 ◽  
Vol 18 (2) ◽  
Author(s):  
D.K. Dond ◽  
N.P. Gulhane
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Direct Injection ◽  
Common Rail ◽  
Injection System ◽  
Injection Timing ◽  
Emission Characteristics ◽  
Performance And Emission ◽  
System Parameters ◽  
Main Injection

Limited fossil fuel reservoir capacity and pollution caused by them is the big problem in front of researchers. In the present paper, an attempt was made to find a solution to the same. The conventional fuel injection system was retrofitted with a simple version of the common rail direct injection system for the small diesel engine. Further, the effect of injection system parameters was observed on the performance and emission characteristics of the retrofitted common rail direct injection diesel engine. The parameters such as injection pressure, the start of pilot injection timing, the start of main injection timing and quantity of percentage fuel injection during the pilot and main injection period were considered for experimental investigation. It was observed that all the evaluated parameters were found vital for improving the engine’s performance and emission characteristics. The retrofitted common rail direct injection system shows an average 7% rise in brake thermal efficiency with economic, specific fuel consumption. At the same time, much more reduction in hydrocarbon, carbon monoxide and smoke opacity with a penalty of a slight increase in nitrogen oxides.

Sign in / Sign up

Export Citation Format

Share Document