scholarly journals Comparison of single and double stage regenerative organic rankine cycle for medium grade heat source through energy and exergy estimation

2019 ◽  
Vol 8 (2) ◽  
pp. 141 ◽  
Author(s):  
Ghalya Pikra ◽  
Nur Rohmah
Keyword(s):  
Heat Source ◽  
Flow Rate ◽  
Power Output ◽  
Thermal Efficiency ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Exergy Efficiency ◽  
Working Fluid ◽  
Energy And Exergy ◽  
Net Power Output

Regenerative organic Rankine cycle (RORC) can be used to improve organic Rankine cycle (ORC) performance. This paper presents a comparison of a single (SSRORC) and double stage regenerative organic Rankine cycle (DSRORC) using a medium grade heat source. Performance for each system is estimated using the law of thermodynamics I and II through energy and exergy balance. Solar thermal is used as the heat source using therminol 55 as a working fluid, and R141b is used as the organic working fluid. The initial data for the analysis are heat source with 200°C of temperature, and 100 L/min of volume flow rate. Analysis begins by calculating energy input to determine organic working fluid mass flow rate, and continued by calculating energy loss, turbine power and pump power consumption to determine net power output and thermal efficiency. Exergy analysis begins by calculating exergy input to determine exergy efficiency. Exergy loss, exergy destruction at the turbine, pump and feed heater is calculated to complete the calculation. Energy estimation result shows that DSRORC determines better net power output and thermal efficiency for 7.9% than SSRORC, as well as exergy estimation, DSRORC determines higher exergy efficiency for 7.69%. ©2019. CBIORE-IJRED. All rights reserved

Analytical Study on Performance of a 250-kW Organic Rankine Cycle System under Off-Design Heat Source Temperatures by the Flow Rate Control Approach

2015 ◽  
Vol 764-765 ◽  
pp. 186-190
Author(s):  
Ben Ran Fu
Keyword(s):  
Heat Source ◽  
Flow Rate ◽  
Rate Control ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Working Fluid ◽  
Control Approach ◽  
Cycle System ◽  
Flow Rate Control ◽  
Net Power Output

A 250-kW organic Rankine cycle system comprised of a preheater, evaporator, condenser, turbine, generator, and pump was used to study its off-design performance and operational control strategy by the flow rate control approach of the working fluid R245fa. The net power output was 243 kW, and the system thermal efficiency was 9.5% under design conditions. The analytical results demonstrated that the flow rate of the working fluid increased with increasing the heat source temperature (TW,in); higher TW,in yielded better heat transfer performance of the designed preheater as well as a higher requirement for the evaporator’s heat capacity; and the net power output increased linearly with increasing TW,in.

Waste Heat Recovery in a Cruise Vessel in the Baltic Sea by Using an Organic Rankine Cycle: A Case Study

2015 ◽  
Author(s):  
Fredrik Ahlgren ◽  
Maria E. Mondejar ◽  
Magnus Genrup ◽  
Marcus Thern
Keyword(s):  
Power Output ◽  
Heat Recovery ◽  
Waste Heat Recovery ◽  
Waste Heat ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Operating Conditions ◽  
Maritime Transportation ◽  
Working Fluid ◽  
Net Power Output

Maritime transportation is a significant contributor to SOx, NOx and particle matter emissions, even though it has a quite low CO2 impact. New regulations are being enforced in special areas that limit the amount of emissions from the ships. This fact, together with the high fuel prices, is driving the marine industry towards the improvement of the energy efficiency of current ship engines and the reduction of their energy demand. Although more sophisticated and complex engine designs can improve significantly the efficiency of the energy systems in ships, waste heat recovery arises as the most influent technique for the reduction of the energy consumption. In this sense, it is estimated that around 50% of the total energy from the fuel consumed in a ship is wasted and rejected in fluid and exhaust gas streams. The primary heat sources for waste heat recovery are the engine exhaust and the engine coolant. In this work, we present a study on the integration of an organic Rankine cycle (ORC) in an existing ship, for the recovery of the main and auxiliary engines exhaust heat. Experimental data from the operating conditions of the engines on the M/S Birka Stockholm cruise ship were logged during a port-to-port cruise from Stockholm to Mariehamn over a period of time close to one month. The ship has four main engines Wärtsilä 5850 kW for propulsion, and four auxiliary engines 2760 kW used for electrical consumers. A number of six load conditions were identified depending on the vessel speed. The speed range from 12–14 knots was considered as the design condition, as it was present during more than 34% of the time. In this study, the average values of the engines exhaust temperatures and mass flow rates, for each load case, were used as inputs for a model of an ORC. The main parameters of the ORC, including working fluid and turbine configuration, were optimized based on the criteria of maximum net power output and compactness of the installation components. Results from the study showed that an ORC with internal regeneration using benzene would yield the greatest average net power output over the operating time. For this situation, the power production of the ORC would represent about 22% of the total electricity consumption on board. These data confirmed the ORC as a feasible and promising technology for the reduction of fuel consumption and CO2 emissions of existing ships.

scholarly journals Utilization of Indonesia’s Hot Spring Sources for Electricity using Kalina Cycle and Organic Rankine Cycle

2018 ◽  
Vol 31 ◽  
pp. 01002 ◽  
Author(s):  
Grano Prabumukti ◽  
Widodo Wahyu Purwanto
Keyword(s):  
Heat Source ◽  
Thermal Efficiency ◽  
Hot Springs ◽  
Hot Spring ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Working Fluid ◽  
Power Capacity ◽  
Spring Temperature ◽  
Kalina Cycle

Indonesia posses 40% of the world's geothermal energy sources. The existence of hydrothermal sources is usually characterized by their surface manifestations such as hot springs, geysers and fumarole. Hot spring has a potential to be used as a heat source to generate electricity especially in a rural and isolated area. Hot springs can be converted into electricity by binary thermodynamic cycles such as Kalina cycle and ORC. The aim of this study is to obtain the best performances of cycle configuration and the potential power capacity. Simulation is conducted using UNISIM software with working fluid and its operating condition as the decision variables. The simulation result shows that R1234yf and propene with simple ORC as desired working fluid and cycle configuration. It reaches a maximum thermal efficiency up to 9.6% with a specific turbine inlet pressure. Higher temperature heat source will result a higher thermal efficiency‥ Cycle thermal efficiency varies from 4.7% to 9.6% depends on source of hot spring temperature. Power capacity that can be generated using Indonesia’s hot spring is ranged from 2 kWe to 61.2 kWe. The highest capacity located in Kawah Sirung and the least located in Kaendi.

scholarly journals Configuration Selection of the Multi-Loop Organic Rankine Cycle for Recovering Energy from a Single Source

Entropy ◽  
2021 ◽  
Vol 23 (11) ◽  
pp. 1435
Author(s):  
Youyi Li ◽  
Tianhao Tang
Keyword(s):  
Heat Source ◽  
Waste Heat ◽  
Organic Rankine Cycle ◽  
Optimal Solution ◽  
Rankine Cycle ◽  
Optimal Number ◽  
Exergy Efficiency ◽  
Working Fluid ◽  
Levelized Cost Of Electricity ◽  
Multi Objective

The Organic Rankine Cycle (ORC) is a well-established way to recover energy from a single waste heat source. This paper aims to select the suitable configuration, number of loops, and working fluids for the Multi-Loop ORC (MLORC) by using multi-objective optimization. The thermodynamic and economic performance of MLORC in three various configurations was analyzed. Multi-objective optimizations of the series and parallel MLORC using different working fluid groups were conducted to find the optimal configuration, number of loops, and working fluid combination. The analysis results show that the series–parallel MLORC performed the worst among the three configurations. The optimization results reveal that series MLORC has a higher exergy efficiency than the parallel MLORC. The exergy efficiency of the optimal solution in series dual-loop, triple-loop, and quadruple-loop ORC is 9.3%, 7.98%, and 6.23% higher than that of parallel ORC, respectively. Furthermore, dual-loop is the optimal number of cycles for recovering energy from a single heat source, according to the grey relational grade. Finally, the series dual-loop ORC using cyclohexane\cyclohexane was the suitable configuration for utilizing a single waste heat source. The exergy efficiency and levelized cost of electricity of the series dual-loop ORC with the optimal parameters are 62.18% and 0.1509 $/kWh, respectively.

scholarly journals Investigation of an Innovative Cascade Cycle Combining a Trilateral Cycle and an Organic Rankine Cycle (TLC-ORC) for Industry or Transport Application

Energies ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 3032 ◽  
Author(s):  
Xiaoli Yu ◽  
Zhi Li ◽  
Yiji Lu ◽  
Rui Huang ◽  
Anthony Roskilly
Keyword(s):  
High Temperature ◽  
System Performance ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Exergy Efficiency ◽  
Working Fluid ◽  
Second Law ◽  
Exergy Destruction ◽  
Second Law Analysis ◽  
Net Power Output

An innovative cascade cycle combining a trilateral cycle and an organic Rankine cycle (TLC-ORC) system is proposed in this paper. The proposed TLC-ORC system aims at obtaining better performance of temperature matching between working fluid and heat source, leading to better overall system performance than that of the conventional dual-loop ORC system. The proposed cascade cycle adopts TLC to replace the High-Temperature (HT) cycle of the conventional dual-loop ORC system. The comprehensive comparisons between the conventional dual-loop ORC and the proposed TLC-ORC system have been conducted using the first and second law analysis. Effects of evaporating temperature for HT and Low-Temperature (LT) cycle, as well as different HT and LT working fluids, are systematically investigated. The comparisons of exergy destruction and exergy efficiency of each component in the two systems have been studied. Results illustrate that the maximum net power output, thermal efficiency, and exergy efficiency of a conventional dual-loop ORC are 8.8 kW, 18.7%, and 50.0%, respectively, obtained by the system using cyclohexane as HT working fluid at THT,evap = 470 K and TLT,evap = 343 K. While for the TLC-ORC, the corresponding values are 11.8 kW, 25.0%, and 65.6%, obtained by the system using toluene as a HT working fluid at THT,evap = 470 K and TLT,evap = 343 K, which are 34.1%, 33.7%, and 31.2% higher than that of a conventional dual-loop ORC.

scholarly journals Experimental and Techno-Economic Analysis of Solar-Geothermal Organic Rankine Cycle Technology for Power Generation in Nepal

2019 ◽  
Vol 2019 ◽  
pp. 1-15 ◽  
Author(s):  
Suresh Baral
Keyword(s):  
Power Generation ◽  
Heat Source ◽  
Power Output ◽  
Solar Collector ◽  
Hot Spring ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Maximum Temperature ◽  
Working Fluid ◽  
Working Fluids

The current research study focuses on the feasibility of stand-alone hybrid solar-geothermal organic Rankine cycle (ORC) technology for power generation from hot springs of Bhurung Tatopani, Myagdi, Nepal. For the study, the temperature of the hot spring was measured on the particular site of the heat source of the hot spring. The measured temperature could be used for operating the ORC system. Temperature of hot spring can also further be increased by adopting the solar collector for rising the temperature. This hybrid type of the system can have a high-temperature heat source which could power more energy from ORC technology. There are various types of organic working fluids available on the market, but R134a and R245fa are environmentally friendly and have low global warming potential candidates. The thermodynamic models have been developed for predicting the performance analysis of the system. The input parameter for the model is the temperature which was measured experimentally. The maximum temperature of the hot spring was found to be 69.7°C. Expander power output, thermal efficiency, heat of evaporation, solar collector area, and hybrid solar ORC system power output and efficiency are the outputs from the developed model. From the simulation, it was found that 1 kg/s of working fluid could produce 17.5 kW and 22.5 kW power output for R134a and R245fa, respectively, when the geothermal source temperature was around 70°C. Later when the hot spring was heated with a solar collector, the power output produced were 25 kW and 30 kW for R134a and R245fa, respectively, when the heat source was 99°C. The study also further determines the cost of electricity generation for the system with working fluids R134a and R245fa to be $0.17/kWh and $0.14/kWh, respectively. The levelised cost of the electricity (LCOE) was $0.38/kWh in order to be highly feasible investment. The payback period for such hybrid system was found to have 7.5 years and 10.5 years for R245fa and R134a, respectively.

Performance Investigation of Solar Organic Rankine Cycle System With Zeotropic Working Fluid Mixtures for Use in Micro-Cogeneration

2021 ◽  
Vol 143 (9) ◽  
Author(s):  
Wahiba Yaïci ◽  
Evgueniy Entchev ◽  
Pouyan Talebizadehsardari ◽  
Michela Longo
Keyword(s):  
Low Temperature ◽  
Power Output ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Working Fluid ◽  
Condensation Temperature ◽  
Source Temperature ◽  
Thermodynamic Performance ◽  
Net Power Output ◽  
Cycle Efficiency

Abstract Overall, there are numerous sustainable sources of renewable, low-temperature heat, principally solar energy, geothermal energy, and energy produced from industrial wastes. Extended utilization of these low-temperature alternatives has a certain capacity of decreasing fossil fuel use with its associated very hazardous greenhouse gas emissions. Researchers have commonly recognized the organic Rankine cycle (ORC) as a feasible and suitable system to produce electrical power from renewable sources based on its advantageous use of volatile organic fluids as working fluids (WFs). Researchers have similarly shown an affinity to the exploitation of zeotropic mixtures as ORC WFs due to their capability to enhance the thermodynamic performance of ORC systems, an achievement supported by improved fits of the temperature profiles of the WF and the heat source/sink. This paper determines both the technical feasibility and the benefits of using zeotropic mixtures as WFs by means of a simulation study of an ORC system. This study analyzes the thermodynamic performance of ORC systems using zeotropic WF mixtures to produce electricity driven by low-temperature solar heat sources for use in buildings. A thermodynamic model is created with an ORC system with and without a regenerator. Five zeotropic mixtures with diverse compositions between 0 and 1 in 0.2 increments of R245fa/propane, R245fa/hexane, R245fa/heptane, pentane/hexane, and isopentane/hexane are assessed and compared with identify the best blends of mixtures that are able to produce superior efficiency in their system cycles. Results disclosed that R245fa/propane (0.4/0.6) with regenerator produces the highest net power output of 7.9 kW and cycle efficiency of 9.4% at the operating condition with a hot source temperature of 85 °C. The study also investigates the effects of the volume flow ratio, and evaporation and condensation temperature glide on the ORC’s thermodynamic performance. Following a thorough analysis of each mixture, R245fa/propane is chosen for a parametric study to examine the effects of operating factors on the system’s efficiency and sustainability index. It was found that the highest cycle efficiency and highest second law cycle efficiency of around 10.5% and 84.0%, respectively, were attained with a mass composition of 0.6/0.4 at the hot source temperature of 95 °C and cold source temperature of 20 °C with a net power output of 9.6 kW. Moreover, results revealed that for zeotropic mixtures, there is an optimal composition range within which binary mixtures are tending to work more efficiently than the component pure fluids. In addition, a significant increase in cycle efficiency can be achieved with a regenerative ORC, with cycle efficiency in the range 3.1–9.8% versus 8.6–17.4% for ORC both without and with regeneration, respectively. In conclusion, utilizing zeotropic mixtures may well expand the restriction faced in choosing WFs for solar-powered ORC-based micro-combined heat and power (CHP) systems.

Energy and Exergy Analysis of an Organic Rankine Cycle used for Ylang-Ylang Essential Oil Distillery Waste Heat Recovery for Power Production in Anjouan Island

2021 ◽  
Vol 1 (1) ◽  
pp. 15-24
Author(s):  
Malik El’Houyoun Ahamadi ◽  
Hery T. Rakotondramiarana
Keyword(s):  
Energy Efficiency ◽  
Essential Oil ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Power Production ◽  
Exergy Efficiency ◽  
Inlet Pressure ◽  
Working Fluid ◽  
Energy And Exergy ◽  
Residual Heat

In the ylang-ylang essential oil distillers in Anjouan Island, the used energy is 100% firewood biomass. A large amount of this energy is dissipated in the environment just in the combustion chamber itself. As it turns out, the flue gases in this process take away the most part of it. Thus, in a process of energy efficiency of stills, the present work aims at assessing the possibility to convert the residual heat from the process into electricity. For that purpose, energy and exergy modeling of an organic Rankine cycle was implemented. It was found that a large amount of exergy is destroyed in the evaporator. Similarly, it emerges that the exergy efficiency of the cycle depends on the inlet temperatures of the exhaust gases in the evaporator and on the inlet pressure of the working fluid in the turbine, and that it is much better for low exhaust gas temperatures. At these low values of gas temperatures, it appears that the improvement in exergy efficiency and energy efficiency are linked to the increase in the inlet pressure of the working fluid in the turbine. It follows from the obtained results that the discharged hot water and the residual heat of gases having temperatures ranging from 180°C to 300 °C, could be used for power production which can reach electrical powers between 1.4kW and 4.5kW  

scholarly journals Investigation of a thermo-fluidic exchange pump in trilateral flash and organic Rankine cycles / trans. from Engl. M. A. Fedorova

2020 ◽  
Vol 4 (4) ◽  
pp. 66-74
Author(s):  
C. R. Baggley ◽  
◽  
M. G. Read ◽  
Keyword(s):  
Low Temperature ◽  
Power Output ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Vapour Phase ◽  
Working Fluid ◽  
Positive Displacement ◽  
Wide Range ◽  
Work Input ◽  
Net Power Output

It is well known that large amounts of energy loss occurs at low temperature states in a wide range of industrial processes., The recovery and reuse of this energy is at the forefront of increasing the overall efficiencies of industrial systems. The aim of this paper is to investigate the effectiveness of using a Thermo-Fluidic Exchange (TFE) pump at low temperature conditions in both a SaturatedVapour Organic Rankine Cycle (SORC) and a Trilateral Flash Cycle (TFC). For some low temperature applications, TFCs have been shown to achieve higher net power output than conventional SORCs, due to their ability to extract more heat from the source fluid. This is the subject of current research as a result of advancements made in the design of positive displacement machines for operation as twophase expanders. Conventional turbines cannot be used for TFCs as they must operate in the vapour phase. One drawback of the TFC is the higher working fluid mass flow rate required. Depending on the scale of the system, this can potentially cause difficulties with pump selection. A TFE pump uses heat input to the system to increase the pressure and temperature of the working fluid, rather than the work input in a standard mechanical pump. This paper compares the net power output achievable using both mechanical and TFE pumps with SORC and TFC systems. The results suggest that the TFE pump could be a viable option for TFC systems

scholarly journals Thermodynamic Performance Analysis of an Improved Two-Stage Organic Rankine Cycle

Energies ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 2864 ◽  
Author(s):  
Xinyu Li ◽  
Tao Liu ◽  
Lin Chen
Keyword(s):  
Heat Exchange ◽  
Output Power ◽  
Thermal Efficiency ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Exergy Efficiency ◽  
Working Fluid ◽  
Outlet Temperature ◽  
Two Stage ◽  
Thermodynamic Performance

In order to improve the two-stage organic Rankine cycle of two heat exchanges of exhaust gas, a two-stage organic Rankine cycle with a regenerator is proposed. Toluene, benzene, cyclohexane and R245fa were selected as the working fluids of the cycle. The thermal efficiency, exergy efficiency and net output power of the cycle were selected as the objective function of the system. The influence of the regenerative performance on the thermodynamic performance of the system was analyzed. The influence of the temperature change of the primary heat exchange outlet on the thermodynamic performance of the system is discussed. The research shows that the regenerator can increase the net power and thermal efficiency of the cycle output. For the selected working fluid, as the efficiency of the regenerator increases, the thermal efficiency of the cycle and the net output power increase. When the primary heat exchange outlet temperature of the exhaust gas increases, the net output power and the exergy efficiency of the cycle increase. For the selected working fluid, when the exhaust heat exchange outlet temperature was increased from 410 K to 490 K, the net output power of the cycle increased up to 10.76 kW, and the exergy efficiency increased up to 7.85%.

Sign in / Sign up

Export Citation Format

Share Document