Flip-chip I/O redistribution technology with low cost stencil printing solder bump

2002 ◽  
Author(s):  
Simon Pui Chung Law
Keyword(s):  
Flip Chip ◽  
Solder Bump ◽  
Low Cost ◽  
Stencil Printing

Thermally Activated Bumping Process using Sn3.0Ag0.5Cu Solder Powder for Low-Cost Interposers

2013 ◽  
Vol 2013 (1) ◽  
pp. 000420-000423
Author(s):  
Kwang-Seong Choi ◽  
Ho-Eun Bae ◽  
Haksun Lee ◽  
Hyun-Cheol Bae ◽  
Yong-Sung Eom
Keyword(s):  
Screen Printing ◽  
Flip Chip ◽  
Solder Bump ◽  
Low Cost ◽  
Organic Substrate ◽  
Lead Free ◽  
Lead Free Solder ◽  
Thermally Activated ◽  
Fine Pitch ◽  
Free Solder

A novel bumping process using solder bump maker (SBM) is developed for fine-pitch flip chip bonding. It features maskless screen printing process with the result that a fine-pitch, low-cost, and lead-free solder-on-pad (SoP) technology can be easily implemented. The process includes two main steps: one is the thermally activated aggregation of solder powder on the metal pads on a substrate and the other is the reflow of the deposited powder on the pads. Only a small quantity of solder powder adjacent to the pads can join the first step, so a quite uniform SoP array on the substrate can be easily obtained regardless of the pad configurations. Through this process, an SoP array on an organic substrate with a pitch of 130 μm is, successfully, formed.

Corrections to "Ultra-fine pitch stencil printing for a low cost and low temperature flip-chip assembly process"

2007 ◽  
Vol 30 (2) ◽  
pp. 359-359
Author(s):  
Robert W. Kay ◽  
Stoyan Stoyanov ◽  
Greg P. Glinski ◽  
Chris Bailey ◽  
Marc P. Y. Desmulliez
Keyword(s):  
Low Temperature ◽  
Flip Chip ◽  
Low Cost ◽  
Assembly Process ◽  
Stencil Printing ◽  
Fine Pitch ◽  
Flip Chip Assembly

Maskless Process for Fabrication of Ultra-Fine Pitch Solder Bumps for Flip Chip Interconnects

2003 ◽  
Vol 125 (4) ◽  
pp. 597-601
Author(s):  
R. T. P. Lee ◽  
A. S. Zuruzi ◽  
S. K. Lahiri
Keyword(s):  
Failure Mode ◽  
Flip Chip ◽  
Solder Bump ◽  
Low Cost ◽  
High Stress ◽  
Lead Free ◽  
Fine Pitch ◽  
Solder Bumps ◽  
Dimensional Uniformity ◽  
Lift Off

The results of this study demonstrate the viability of a low cost maskless process for the fabrication of ultra-fine pitch solder bumps. The fabricated solder bump arrays have a pitch and diameter of 120 and 70 μm, respectively. Widely used eutectic 63Sn37Pb and lead-free 95.5Sn3.8Ag0.7Cu solders were used to form the bumps. No solder bridging was observed between adjacent bumps, and the solder bumps exhibited good dimensional uniformity. The solder bump to aluminum (Al) pad bond integrity was found to be excellent, as evidenced by the high stress to failure. The failure mode is predominately Al pad lift-off indicating a robust solder bump-pad joint.

Electrolytic Deposition of Fine Pitch Sn/Cu Solder Bumps for Flip Chip Packaging

2012 ◽  
Vol 2012 (1) ◽  
pp. 000729-000734
Author(s):  
Stephen Kenny ◽  
Kai Matejat ◽  
Sven Lamprecht ◽  
Olivier Mann
Keyword(s):  
Copper Alloy ◽  
Flip Chip ◽  
Solder Bump ◽  
Electroless Nickel ◽  
Practical Experience ◽  
Electrolytic Deposition ◽  
Solder Paste ◽  
Stencil Printing ◽  
Printing Process ◽  
Solder Bumps

Current methods for the formation of pre-solder bumps for flip chip attachment use stencil printing techniques with an appropriate alloy solder paste. The continuing trend towards increased miniaturization and the associated decrease in size of solder resist opening, SRO is causing production difficulties with the stencil printing process. Practical experience of production yields has shown that stencil printing will not be able to meet future requirements for solder bump pitch production below 150μm for these applications. This paper describes latest developments in the electrolytic deposition of solder to replace the stencil printing process; results from production of 90μm bump pitch solder arrays with tin/copper alloy are given. The solder bump is produced with a specially developed electrolytic tin process which fills a photo resist defined structure on the SRO. The photoresist dimensions determine the volume of solder produced and the subsequent bump height after reflow. Investigations on the bump reliability after reflow are shown including copper alloy concentration at 0.7% and x-ray investigation to confirm uniform metal deposition. The self centering mechanism found in the bump production process during reflow is presented and the capability to correct photoresist registration issues. The solder bumps are shown as deposited onto an electroless nickel/gold or electroless nickel/palladium/gold final finish which serves also as a barrier layer to copper diffusion into the solder bump. Discussion of further development work in the production of alloys of tin/copper together with silver are given with first test results.

Ultra-Fine Pitch Stencil Printing for a Low Cost and Low Temperature Flip-Chip Assembly Process

2007 ◽  
Vol 30 (1) ◽  
pp. 129-136 ◽  
Author(s):  
Robert W. Kay ◽  
Stephen Stoyanov ◽  
Greg P. Glinski ◽  
Chris Bailey ◽  
Marc P. Y. Desmulliez
Keyword(s):  
Low Temperature ◽  
Flip Chip ◽  
Low Cost ◽  
Assembly Process ◽  
Stencil Printing ◽  
Fine Pitch ◽  
Flip Chip Assembly

Interfacial reaction and joint reliability of fine-pitch flip-chip solder bump using stencil printing method

2007 ◽  
Vol 84 (11) ◽  
pp. 2640-2645 ◽  
Author(s):  
Sang-Su Ha ◽  
Dae-Gon Kim ◽  
Jong-Woong Kim ◽  
Jeong-Won Yoon ◽  
Jin-Ho Joo ◽  
...  
Keyword(s):  
Interfacial Reaction ◽  
Flip Chip ◽  
Solder Bump ◽  
Stencil Printing ◽  
Joint Reliability ◽  
Fine Pitch ◽  
Printing Method

The Use of Precision Selective Area Milling for Failure Analysis of Flip-Chip Packages

2002 ◽  
Author(s):  
George F. Gaut
Keyword(s):  
Failure Analysis ◽  
Flip Chip ◽  
Solder Bump ◽  
Selective Area ◽  
Fill Material ◽  
Solder Bumps ◽  
Time Required

Abstract Access to the solder bump and under-fill material of flip-chip devices has presented a new problem for failure analysts. The under-fill and solder bumps have also added a new source for failure causes. A new tool has become available that can reduce the time required to analyze this area of a flip-chip package. By using precision selective area milling it is possible to remove material (die or PCB) that will allow other tools to expose the source of the failure.

Defect Detection of Flip Chip Solder Bumps Through Local Temporal Coherence Analysis of Laser Ultrasound Signals

2007 ◽  
Author(s):  
Jin Yang ◽  
Charles Ume
Keyword(s):  
Defect Detection ◽  
Flip Chip ◽  
Solder Bump ◽  
Temporal Coherence ◽  
Coherence Analysis ◽  
Laser Ultrasound ◽  
Surface Mount ◽  
Flip Chips ◽  
Solder Bumps ◽  
Ultrasound Signals

Microelectronics packaging technology has evolved from through-hole and bulk configuration to surface-mount and small-profile ones. In surface mount packaging, such as flip chips, chip scale packages (CSP), and ball grid arrays (BGA), chips/packages are attached to the substrates or printed wiring boards (PWB) using solder bump interconnections. Solder bumps, which are hidden between the device and the substrate/board, are no longer visible for inspection. A novel solder bump inspection system has been developed using laser ultrasound and interferometric techniques. This system has been successfully applied to detect solder bump defects including missing, misaligned, open, and cracked solder bumps in flip chips, and chip scale packages. This system uses a pulsed Nd:YAG laser to induce ultrasound in the thermoelastic regime and the transient out-of-plane displacement response on the device surface is measured using the interferometric technique. In this paper, local temporal coherence (LTC) analysis of laser ultrasound signals is presented and compared to previous signal processing methods, including Error Ratio and Correlation Coefficient. The results show that local temporal coherence analysis increases measurement sensitivity for inspecting solder bumps in packaged electronic devices. Laser ultrasound inspection results are also compared with X-ray and C-mode Scanning Acoustic Microscopy (CSAM) results. In particular, this paper discusses defect detection for a 6.35mm×6.35mm×0.6mm PB18 flip chip and a flip chip (SiMAF) with 24 lead-free solder bumps. These two flip chip specimens are both non-underfilled.

Sign in / Sign up

Export Citation Format

Share Document