Effect of Activating Agent on the Preparation of Bamboo-Based High Surface Area Activated Carbon by Microwave Heating

2016 ◽  
Vol 35 (6) ◽  
pp. 535-541 ◽  
Author(s):  
Hongying Xia ◽  
Jian Wu ◽  
Chandrasekar Srinivasakannan ◽  
Jinhui Peng ◽  
Libo Zhang
Keyword(s):  
Activated Carbon ◽  
Microwave Heating ◽  
Surface Area ◽  
Pore Volume ◽  
Activated Carbons ◽  
High Surface ◽  
High Surface Area ◽  
Significant Proportion ◽  
Mixture Ratio ◽  
Activating Agent

AbstractThe present work attempts to convert bamboo into a high surface area activated carbon via microwave heating. Different chemical activating agents such as KOH, NaOH, K2CO3 and Na2CO3 were utilized to identify a most suitable activating agent. Among the activating agents tested KOH was found to generate carbon with the highest porosity and surface area. The effect of KOH/C ratio on the porous nature of the activated carbon has been assessed. An optimal KOH/C ratio of 4 was identified, beyond which the surface area as well as the pore volume were found to decrease. At the optimized KOH/C ratio the surface area and the pore volume were estimated to be 3,441 m2/g and 2.093 ml/g, respectively, with the significant proportion of which being microporous (62.3%). Activated carbon prepared under the optimum conditions was further characterized using Fourier transform infrared spectroscopy (FTIR) and scanning electron microscope (SEM). Activated carbons with so high surface area and pore volume are very rarely reported, which could be owed to the nature of the precursor and the optimal conditions of mixture ratio adopted in the present work.

scholarly journals Effect of Microwave Heating Conditions on the Preparation of High Surface Area Activated Carbon from Waste Bamboo

2015 ◽  
Vol 34 (7) ◽  
pp. 667-674
Author(s):  
Jian Wu ◽  
Hongying Xia ◽  
Libo Zhang ◽  
Yi Xia ◽  
Jinhui Peng ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Microwave Heating ◽  
Surface Area ◽  
Microwave Power ◽  
High Surface ◽  
High Surface Area ◽  
Significant Proportion ◽  
Heating Time ◽  
Raw Material ◽  
Carbon Surface

Abstract The present study reports the effect of microwave power and microwave heating time on activated carbon adsorption ability. The waste bamboo was used to preparing high surface area activated carbon via microwave heating. The bamboo was carbonized for 2 h at 600°C to be used as the raw material. According to the results, microwave power and microwave heating time had a significant impact on the activating effect. The optimal KOH/C ratio of 4 was identified when microwave power and microwave heating time were 700 W and 15 min, respectively. Under the optimal conditions, surface area was estimated to be 3441 m2/g with pore volume of 2.093 ml/g and the significant proportion of activated carbon was microporous (62.3%). The results of Fourier transform infrared spectroscopy (FTIR) were illustrated that activated carbon surface had abundant functional groups. Additionally the pore structure is characterized using Scanning Electron Microscope (SEM).

scholarly journals Preparation and characterization of activated carbons from albizia saman pod

2017 ◽  
Vol 36 (3) ◽  
pp. 44-53
Author(s):  
G. D. Akpen ◽  
M. I. Aho ◽  
N. Baba
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Activated Carbons ◽  
High Surface ◽  
High Surface Area ◽  
Volatile Matter ◽  
Sieve Analysis ◽  
Albizia Saman ◽  
Temperature Surface

Activated carbon was prepared from the pods of Albizia saman for the purpose of converting the waste to wealth. The pods were thoroughly washed with water to remove any dirt, air- dried and cut into sizes of 2-4 cm. The prepared pods were then carbonised in a muffle furnace at temperatures of 4000C, 5000C, 6000C ,7000C and 8000C for 30 minutes. The same procedure was repeated for 60, 90, 120 and 150 minutes respectively. Activation was done using impregnationratios of 1:12, 1:6, 1:4, 1:3, and 1:2 respectively of ZnCl2 to carbonised Albizia saman pods by weight. The activated carbon was then dried in an oven at 1050C before crushing for sieve analysis. The following properties of the produced Albizia saman pod activated carbon (ASPAC) were determined: bulk density, carbon yield, surface area and ash, volatile matter and moisture contents. The highest surface area of 1479.29 m2/g was obtained at the optimum impregnation ratio, carbonization time and temperature of 1:6, 60 minutes and 5000C respectively. It was recommended that activated carbon should be prepared from Albizia saman pod with high potential for adsorption of pollutants given the high surface area obtained.Keywords: Albizia saman pod, activated carbon, carbonization, temperature, surface area

A comparison of different activated carbon performances on catalytic ozonation of a model azo reactive dye

2012 ◽  
Vol 66 (1) ◽  
pp. 179-184 ◽  
Author(s):  
Ş. Gül ◽  
O. Eren ◽  
Ş. Kır ◽  
Y. Önal
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Activated Carbons ◽  
High Surface ◽  
High Surface Area ◽  
Reactive Dye ◽  
Catalytic Ozonation ◽  
Bet Surface Area ◽  
Solution Ph ◽  
Pore Properties

The objective of this study is to compare the performances of catalytic ozonation processes of two activated carbons prepared from olive stone (ACOS) and apricot stone (ACAS) with commercial ones (granular activated carbon-GAC and powder activated carbon-PAC) in degradation of reactive azo dye (Reactive Red 195). The optimum conditions (solution pH and amount of catalyst) were investigated by using absorbencies at 532, 220 and 280 nm wavelengths. Pore properties of the activated carbon (AC) such as BET surface area, pore volume, pore size distribution, and pore diameter were characterized by N2 adsorption. The highest BET surface area carbon (1,275 m2/g) was obtained from ACOS with a particle size of 2.29 nm. After 2 min of catalytic ozonation, decolorization performances of ACOS and ACAS (90.4 and 91.3%, respectively) were better than that of GAC and PAC (84.6 and 81.2%, respectively). Experimental results showed that production of porous ACs with high surface area from olive and apricot stones is feasible in Turkey.

The Effect of Activated Carbon Properties on the Adsorption of Toxic Substances

1992 ◽  
Vol 25 (1) ◽  
pp. 153-160 ◽  
Author(s):  
E. Diamadopoulos ◽  
P. Samaras ◽  
G. P. Sakellaropoulos
Keyword(s):  
Activated Carbon ◽  
Fulvic Acid ◽  
Surface Area ◽  
Activated Carbons ◽  
High Surface ◽  
High Surface Area ◽  
Ash Content ◽  
Adsorptive Capacity ◽  
Toxic Substances ◽  
Carbon Loading

The objectives of this work were to relate the activated carbon properties to its adsorptive capacity. The activated carbon needed was produced in the lab from Greek lignite coal. Subsequently, adsorption studies were performed in order to evaluate the efficiency of the various activated carbons to remove toxic substances from water. Two organic substances were used. These were phenol and fulvic acid. Additionally, the adsorption of arsenic (V) was, also, investigated. It was found that the adsorptive capacity of the activated carbons depended primarily on the ash content and the compound. The capacity of the carbon to remove phenol, expressed as mg of phenol removed per g of activated carbon (carbon loading), decreased linearly as the amount of ash in the activated carbon increased. Ash-free activated carbons could adsorb 4 times as much phenol as the activated carbons with a high ash content. On the other hand, fulvic acid and arsenic adsorbed poorly on the ash-free activated carbons. Even for the high surface area activated carbons (over 1000 m2/g), the quantity of fulvic acid or arsenic adsorbed was significantly less than that exhibited by the high ash activated carbons (maximum surface area measured hardly exceeded 300 m2/g). As the amount of ash in the carbon increased, the carbon loading increased as well, up to a certain level, beyond which the amount of ash played no significant role. The beneficial role of ash was explained by the ability of the fulvic acid and arsenic to interact with metal oxides and metal ions, which constitute a significant fraction of the ash.

scholarly journals Activated Carbon from Rice Husk Biochar with High Surface Area

2020 ◽  
Vol 11 (3) ◽  
pp. 10265-10277
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Rice Husk ◽  
Activated Carbons ◽  
Solid Phase ◽  
Chemical Activation ◽  
High Surface ◽  
High Surface Area ◽  
Array Detector ◽  
Functional Density Theory

Activated carbons derived from rice husk pyrolysis (biochar) were prepared by chemical activation at different biochar/K2CO3 proportions in order to assess its capacity as adsorbent. The activated material was characterized by X-ray diffraction (DRX), Raman spectroscopy, scanning electron microscopy (SEM), the Brunauer, Emmet, and Teller (BET) method. The Barret, Joyner, and Halenda (BJH) method and functional density theory (DFT), presenting interesting texture properties, such as high surface area (BET 1850 m2 g-1) and microporosity, which allow its use as a sorbent phase in solid-phase extraction (SPE) of the main constituents of the aqueous pyrolysis phase. It was demonstrated that the activated carbon (RH-AC) adsorbs different compounds present in from rice husk pyrolysis wastewater through quantitative analysis by high-performance liquid chromatography with a diode-array detector (HPLC-DAD), presenting good linearity (R2 > 0.996) at 280 nm.

Preparation and Characterization of Magnetic Coal-Based Activated Carbon in the Presence of Fe3O4

2011 ◽  
Vol 393-395 ◽  
pp. 1355-1358 ◽  
Author(s):  
Jun Zhang
Keyword(s):  
Magnetic Properties ◽  
Activated Carbon ◽  
Surface Area ◽  
Pore Volume ◽  
High Surface ◽  
High Surface Area ◽  
Vibrating Sample Magnetometer ◽  
N2 Adsorption ◽  
Magnetic Activated Carbon

Magnetic coal-based activated carbon was prepared from Taixi anthracitic coal in the presence of magnetite (Fe3O4). The magnetic activated carbon samples were characterized by N2 adsorption, XRD, FTIR and vibrating sample magnetometer (VSM). It was found that the magnetic activated carbon had a high surface area of 993.5 m2/g with 4% Fe3O4 and a saturation magnetization of 2.4158 emu/g for magnetic separability. The results showed that the magnetic properties of MAC are provided by Fe3O4 and Fe. In the presence of Fe3O4, the rate of carbonization and activation increase to form a large surface area and a high pore volume. Moreover, the addition of Fe3O4 can greatly promote the number of both micro-pores and meso-pores in activated carbon.

Production of High Surface Area Activated Carbon from Coconut Husk

2014 ◽  
Vol 1644 ◽  
Author(s):  
Paul R. Armstrong ◽  
Zachary J. Morchesky ◽  
Dustin T. Hess ◽  
Kofi W. Adu ◽  
David. K. Essumang ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Activated Carbons ◽  
Raw Materials ◽  
Chemical Activation ◽  
High Surface ◽  
Waste Product ◽  
High Surface Area ◽  
Coconut Husk ◽  
Porosity Analysis

ABSTRACTWe present preliminary results on a processing protocol by chemical activation that transforms organic waste product such as coconut husk into high surface area activated carbon. Dried raw materials of the coconut husk were carbonized anaerobically into char. The char was impregnated with KOH of different ratios and were activated at 800°C and 900°C. The transmission electron microscope was used to acquire structural and morphological information of the activated carbon, and the surface area and porosity analysis were performed using Micromeritics ASAP 2020 analyzer. The activated carbons show both micropores and mesopores with specific surface area as high as 2900m2/g.

scholarly journals Chestnut-Derived Activated Carbon as a Prospective Material for Energy Storage

Materials ◽  
2020 ◽  
Vol 13 (20) ◽  
pp. 4658 ◽  
Author(s):  
Katarzyna Januszewicz ◽  
Anita Cymann-Sachajdak ◽  
Paweł Kazimierski ◽  
Marek Klein ◽  
Justyna Łuczak ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Activated Carbons ◽  
Chemical Activation ◽  
High Surface ◽  
High Surface Area ◽  
Rate Capability ◽  
Activation Process ◽  
Porous Carbons ◽  
Subsequent Activation

In this work, we present the preparation and characterization of biomass-derived activated carbon (AC) in view of its application as electrode material for electrochemical capacitors. Porous carbons are prepared by pyrolysis of chestnut seeds and subsequent activation of the obtained biochar. We investigate here two activation methods, namely, physical by CO2 and chemical using KOH. Morphology, structure and specific surface area (SSA) of synthesized activated carbons are investigated by Brunauer-Emmett-Teller (BET) technique and scanning electron microscopy (SEM). Electrochemical studies show a clear dependence between the activation method (influencing porosity and SSA of AC) and electric capacitance values as well as rate capability of investigated electrodes. It is shown that well-developed porosity and high surface area, achieved by the chemical activation process, result in outstanding electrochemical performance of the chestnut-derived porous carbons.

Sign in / Sign up

Export Citation Format

Share Document