Influence of a locally variable mold temperature on injection molded thin-wall components

2018 ◽  
Vol 38 (5) ◽  
pp. 475-481 ◽  
Author(s):  
Christopher Fischer ◽  
Ariane Jungmeier ◽  
Guido Peters ◽  
Dietmar Drummer
Keyword(s):  
Injection Molding ◽  
Mold Temperature ◽  
Thin Wall ◽  
Cooling Conditions ◽  
Mechanical Component ◽  
First Results ◽  
Injection Molded ◽  
Wall Components

Abstract Regarding injection-molding of semi-crystalline thermoplastics, controlling mold temperature and, therefore, the polymer melt’s cooling conditions can significantly affect component properties. In this research, an innovative dynamically tempered mold technology with different temperature zones is investigated, which will allow the production of thin-wall components with locally different component properties. First results show that due to influencing inner component properties, significant differences in optical and mechanical component properties can be achieved.

scholarly journals Post-Processing Time Dependence of Shrinkage and Mechanical Properties of Injection-Molded Polypropylene

Materials ◽  
2020 ◽  
Vol 14 (1) ◽  
pp. 22
Author(s):  
Artur Kościuszko ◽  
Dawid Marciniak ◽  
Dariusz Sykutera
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Injection Molding ◽  
Accelerated Aging ◽  
Mold Temperature ◽  
Degree Of Crystallinity ◽  
Injection Mold ◽  
Secondary Crystallization ◽  
Scanning Calorimetry ◽  
Injection Molded

Dimensions of the injection-molded semi-crystalline materials (polymeric products) decrease with the time that elapses from their formation. The post-molding shrinkage is an effect of secondary crystallization; the increase in the degree of polymer crystallinity leads to an increase in stiffness and decrease in impact strength of the polymer material. The aim of this study was to assess the changes in the values of post-molding shrinkage of polypropylene produced by injection molding at two different temperatures of the mold (20 °C and 80 °C), and conditioned for 504 h at 23 °C. Subsequently, the samples were annealed for 24 h at 140 °C in order to conduct their accelerated aging. The results of shrinkage tests were related to the changes of mechanical properties that accompany the secondary crystallization. The degree of crystallinity of the conditioned samples was determined by means of density measurements and differential scanning calorimetry. It was found that the changes in the length of the moldings that took place after removal from the injection mold were accompanied by an increase of 20% in the modulus of elasticity, regardless of the conditions under which the samples were made. The differences in the shrinkage and mechanical properties of the samples resulting from mold temperature, as determined by tensile test, were removed by annealing. However, the samples made at two different injection mold temperature values still significantly differed in impact strength, the values of which were clearly higher for the annealed samples compared to the results determined for the samples immediately after the injection molding.

Warpage Measurement of a Micro Electrical Fan on Micro-Injection Molding

2012 ◽  
Vol 184-185 ◽  
pp. 1651-1654
Author(s):  
Jeou Long Lee ◽  
Y. Lin ◽  
Y.K. Shen
Keyword(s):  
Injection Molding ◽  
Injection Pressure ◽  
Acrylonitrile Butadiene Styrene ◽  
Mold Temperature ◽  
Micro Injection Molding ◽  
Optimum Result ◽  
Suitable Material ◽  
Packing Pressure ◽  
Injection Molded ◽  
Packing Time

This study characterizes warpage of a micro-injection molded micro electrical fan using the Michelson interference method. This study conducts experiments to analyze different polymers-polypropylene (PP), polyamide (PA), acrylonitrile-butadiene styrene (ABS), ABS+ polycarbonate (PC), and polyoxymethylene (POM)-process parameters, such as mold temperature, injection temperature, injection pressure, injection time, packing time, and packing pressure, for a micro electrical fan. To obtain the optimum result (minimum warpage), this study assesses the effect (warpage) of each material on micro-injection molding. PA plastic is the very suitable material for micro electrical fan with Michelson interference analysis on micro-injection molding.

Numerical and Experimental Study on the Injection Moulding of a Thin-Wall Complex Part

2008 ◽  
Author(s):  
Catalin Fetecau ◽  
Ion Postolache ◽  
Felicia Stan
Keyword(s):  
Injection Molding ◽  
Injection Pressure ◽  
Mold Temperature ◽  
Processing Parameters ◽  
Injection Molding Process ◽  
Thin Wall ◽  
Molding Process ◽  
Complex Part ◽  
Filling Time ◽  
Wall Injection

The research presented in this paper involves numerical and experimental efforts to investigate the relative thin-wall injection molding process in order to obtain high dimensional quality complex parts. To better understand the effects of various processing parameters (the filling time, injection pressure, the melting temperature, the mold temperature) on the injection molding of a thin-wall complex part, the molding experiments are regenerated into the computer model using the Moldflow Plastics Insight (MPI) 6.1 software. The computer visualization of the filling phase allows accurate prediction of the location of the flow front, welding lines and air traps. Furthermore, in order to optimize the injection molding process, the effects of the geometry of the runner system on the filling and packing phases are also investigated. It is shown that computational modeling could be used to help the process and mold designer to produce accurate parts.

Application of a multilayer injection molding process for thick-walled optical components

2016 ◽  
Vol 36 (6) ◽  
pp. 557-562 ◽  
Author(s):  
Christian Hopmann ◽  
Malte Röbig
Keyword(s):  
Optical Properties ◽  
Injection Molding ◽  
Mold Temperature ◽  
Injection Molding Process ◽  
Molding Process ◽  
Optical Components ◽  
Considerable Potential ◽  
Cycle Times ◽  
Molded Part ◽  
Injection Molded

Abstract Nowadays, the injection molding of optical components is becoming more and more important. A process which constructs the injection-molded part in layers offers considerable potential for productivity increases in the manufacturing of thick-walled optical components. The so-called multilayer injection molding, also known as overmolding technology enables a considerable reduction of the normally long cycle times and improves the optical properties. It is even possible to increase the molding accuracy due to the lower shrinkage potential of the single layers. Contrary to experience, the influence of the mold temperature on the bonding strength is very low. So, the temperature control of the mold can be adapted to the process consideration in regard to optical characteristics.

scholarly journals Dielectric Spectroscopy of PP/MWCNT Nanocomposites: Relationship with Crystalline Structure and Injection Molding Condition

Nanomaterials ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 550
Author(s):  
Marco Monti ◽  
Marta Zaccone ◽  
Alberto Frache ◽  
Luigi Torre ◽  
Ilaria Armentano
Keyword(s):  
Injection Molding ◽  
Crystalline Structure ◽  
Processing Condition ◽  
Mold Temperature ◽  
Dielectric Behavior ◽  
Multi Walled Carbon Nanotube ◽  
Molding Condition ◽  
Frequency Independent ◽  
Injection Molded ◽  
Independent Behavior

In this paper, we study the correlation between the dielectric behavior of polypropylene/multi-walled carbon nanotube (PP/MWCNT) nanocomposites and the morphology with regard to the crystalline structure, nanofiller dispersion and injection molding conditions. As a result, in the range of the percolation threshold the dielectric behavior shifts to a more frequency-independent behavior, as the mold temperature increases. Moreover, the position further from the gate appears as the most conductive. This effect has been associated to a modification of the morphology of the MWCNT clusters induced by both the flow of the molten polymer during the processing phase and the variation of the crystalline structure, which is increasingly constituted by γ-phase as the mold temperature increases. The obtained results allow one to understand the effect of tuning the processing condition in the frequency-dependent electrical behavior of PP/MWCNT injection-molded nanocomposites, which can be successfully exploited for an advanced process/product design.

scholarly journals The use of IR thermography to show the mold and part temperature evolution in injection molding

2016 ◽  
Vol 36 (1) ◽  
pp. 40-43 ◽  
Author(s):  
Karol Bula ◽  
Leszek Różański ◽  
Lidia Marciniak-Podsadna ◽  
Dawid Wróbel
Keyword(s):  
Injection Molding ◽  
Isotactic Polypropylene ◽  
Infrared Camera ◽  
Mold Temperature ◽  
Temperature Evolution ◽  
Injection Mold ◽  
Ir Thermography ◽  
Molded Parts ◽  
Injection Molded

Abstract This study concerns the application of infrared camera for injection molding analysis by measuring temperatures of both injection molded parts and injection mold cavities in a function of injection cycles. The mold with two cavities, differing in thickness (1 and 3 mm), and a cold direct runner was used. Isotactic polypropylene homopolymer was utilized to produce parts. Mold temperature was set at 22°C and controlled by a water chiller. Five measuring points were determined: SP1, SP2 (placed in the 3 mm cavity), SP3, SP4 (located in the 1 mm cavity) and SP5 around an injection molding gate. Our investigations showed that the highest temperature is localized around SP2 point and the lowest at SP4. Also, it was proved that even after 62 injection molding cycles, temperatures of cavities were not stable, revealing their further increase with each cycle.

Flake Orientation in Injection Molding of Pigmented Thermoplastics

2012 ◽  
Vol 134 (1) ◽  
Author(s):  
Jang Min Park ◽  
Seok Jae Jeong ◽  
Seong Jin Park
Keyword(s):  
Injection Molding ◽  
Experimental Studies ◽  
Mold Temperature ◽  
Orientation Distribution ◽  
Injection Molding Process ◽  
Molding Process ◽  
Part Surface ◽  
Orientation State ◽  
Abs Resin ◽  
Injection Molded

In the present work, experimental studies are carried out to understand orientation kinematics of pigment flakes during the injection molding process. The injection molding experiments are carried out using ABS resin compounded with aluminum flakes. Thin specimens are sliced off from the injection molded sample, and then the orientation distribution is observed using transmitted microscopy. Generally, the microscopic result shows a sandwich structure where the orientation state near the mid-plane differs significantly from that around the surface. Particularly at the weldline region, locally different orientation is observed near the part surface, which is the result of fountain flow at the melt front. Also the effect of mold temperature on the flake orientation is presented.

scholarly journals Study on External Gas-Assisted Mold Temperature Control for Improving the Melt Flow Length of Thin Rib Products in the Injection Molding Process

2019 ◽  
Vol 2019 ◽  
pp. 1-17 ◽  
Author(s):  
Phan The Nhan ◽  
Thanh Trung Do ◽  
Tran Anh Son ◽  
Pham Son Minh
Keyword(s):  
Injection Molding ◽  
Temperature Control ◽  
High Efficiency ◽  
Mold Temperature ◽  
Injection Molding Process ◽  
Thin Wall ◽  
Mold Surface ◽  
Melt Flow ◽  
Molding Process ◽  
Flow Length

In the injection molding process, mold temperature control is one of the most efficient methods for improving product quality. In this research, an external gas-assisted mold temperature control (Ex-GMTC) with gas temperature variation from 200°C to 400°C was applied to thin wall injection molding at melt thicknesses from 0.2 to 0.6 mm. The melt flow length was evaluated through the application of this system to the mold of a thin rib product. The results show that the heating process achieves high efficiency in the initial 20 s, with a maximum heating rate of 6.4°C/s. In this case, the mold surface reached 158.4°C. By applying Ex-GMTC to a 0.2 mm flow thickness, the flow length increased from 37.85 to 41.32 mm with polypropylene (PP) material and from 14.54 to 15.8 mm with acrylonitrile butadiene styrene (ABS) material. With the thin rib mold and use of Ex-GMTC, the mold temperature varied from 112.0°C to 140.8°C and the thin rib height reached 7.0 mm.

scholarly journals The feasibility of external gas-assisted mold-temperature control for thin-wall injection molding

2018 ◽  
Vol 10 (10) ◽  
pp. 168781401880610 ◽  
Author(s):  
Pham Son Minh ◽  
Thanh Trung Do ◽  
Tran Minh The Uyen
Keyword(s):  
Temperature Distribution ◽  
Injection Molding ◽  
Heating Rate ◽  
Temperature Control ◽  
Mold Temperature ◽  
Cavity Surface ◽  
Thin Wall ◽  
Mold Surface ◽  
Hot Gas ◽  
Wall Injection

Simulation and experimental testing were conducted on an external gas-assisted mold-temperature control combined with a pulsed cooling system used for thin-wall injection molding to determine its effect on the heating rate and temperature distribution of a mold surface. For mold heating via external gas-assisted mold-temperature control, a hot gas was directly discharged on the cavity surface. Based on the heat convection between the hot gas and the cavity surface, the cavity temperature rose to the target value. Practically, the gap between the heating surface and the gas gate is an important parameter as it strongly influences the heating process. Therefore, this parameter was analyzed under different values of plate-insert thickness herein. Heating was elucidated by the temperature distribution and heating-rate data detected by the infrared camera and sensors. Then, external gas-assisted mold-temperature control was applied for the thin-wall injection-molding part of 0.5 mm thickness with the local-gate-temperature control. The results show that with 300°C gas temperature, the heating rate could reach 9°C/s with a 0.5-mm stamp thickness and a 4-mm gas gap. The results show that with local heating at the melt-entrance area of the mold plate, the cavity was filled with a 20-s heating cycle.

Sign in / Sign up

Export Citation Format

Share Document