scholarly journals A review on thermo-physical properties of bio, non-bio and hybrid nanofluids

2019 ◽  
Vol 13 (4) ◽  
pp. 5875-5904
Author(s):  
James Lau Tze Chen ◽  
Ahmed N. Oumer ◽  
Azizuddin A. A.
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Physical Properties ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Material Type ◽  
Low Viscosity ◽  
Water Based ◽  
Influential Parameters ◽  
Thermo Physical Properties

The pressure drop and thermal performance of various nanofluids can be affected by their thermo-physical properties. However, there are many different parameters that need to be considered when determining the thermo-physical properties of nanofluids. This paper highlights a detail reviews on the thermo-physical properties of nanofluids with different material type and effect of some process parameters (such as material type, temperature and concentration) on the thermo-physical properties of nanofluids. Four thermo-physical properties mainly density, viscosity, thermal conductivity and specific heat capacity from different literatures were summarized, discussed and presented. The lowest viscosity value of nanofluids in literature was mango bark water-based nanofluid (0.81cP). On the other hand, the maximum thermal conductivity value of nanofluids in the literature was GNP-Ag water-based nanofluid (0.69W/mK). The density and specific heat capacity are strongly dependent on the material type. Meanwhile, the viscosity and thermal conductivity are greatly affected by temperature and concentration. The most influential parameters on thermo-physical properties of nanofluids are material type followed by temperature. Most of the literatures confirmed bio nanofluids have low viscosity value and hybrid have high thermal conductivity values.

scholarly journals The influence of utrafine-grained state on thermo-physical properties of Zr-1 wt.% Nb and Ti-45 wt.% Nb alloys and processes of dissipation and accumulation of energy during deformation

2020 ◽  
pp. 28-35
Author(s):  
E.V. Legostaeva ◽  
◽  
Yu.P. Sharkeev ◽  
O.A. Belyavskaya ◽  
V.P. Vavilov ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Plastic Deformation ◽  
Heat Capacity ◽  
Physical Properties ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Coarse Grained ◽  
Ultrafine Grained ◽  
Substructural Hardening ◽  
Thermo Physical Properties

The results of studying the thermal conductivity and specific heat capacity of Zr-1 wt.% Nb and Ti-45 wt.% Nb in coarse-grained and ultrafine-grained states are presented. The influence of the utrafine-grained state on the thermo physical properties and the processes of dissipation and accumulation energy during deformation of the alloys are estimated. It is shown that formation of the ultrafine-grained state in the Zr-1 wt.% Nb alloy by abc -pressing and subsequent rolling leads to a decrease in its thermal conductivity and specific heat capacity by 10 and 20%, respectively, due to substructural hardening under severe plastic deformation. It is found that thermal conductivity and specific heat capacity of the ultrafine Ti-45 wt.% Nb alloy increase by 7.5 and 5%, respectively, due to dispersion hardening of the ω phase by nanoparticles and formation of a new α phase. It is established that the ultrafine-grained structure has a significant influence on the regularities of the dissipation and accumulation energy during plastic deformation, which in turn depend on their thermo-physical characteristics and on the structural and phase state.

scholarly journals Studies on thermo physical property variations of graphene nanoparticle suspended ethylene glycol/water

2020 ◽  
pp. 36-36
Author(s):  
Manikandan Periasamy ◽  
Rajoo Baskar
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Ethylene Glycol ◽  
Physical Properties ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Base Fluid ◽  
Physical Property ◽  
Inlet Temperature ◽  
Thermo Physical Properties

The objective of the study is to determine the thermo physical property variations (such as viscosity, density, specific heat capacity and thermal conductivity) of graphene suspended base fluid (Ethylene Glycol (EG) /Water (W)), with respect to graphene nanoparticle concentration and hot fluid inlet temperature. Graphene nanoparticle concentrations (0.2, 0.4, 0.6, 0.8 and 1 volume %) and the base fluid of 30:70 volume % of EG: Water is prepared initially. The impact of graphene nano particle addition on base fluids based on experimentation in the commercial plate heat exchanger was studied. In this experiment, the hot fluid inlet temperature was varied at 55? C, 65? C and 75? C. The experimental results of thermo physical properties were compared with the selected models proposed in the literature. Einstein (1956); Kitano (1981); and Bachelor models (1977) have been used to consider the effect of viscosity. The measured density and Specific heat capacity was validated with Pak and Cho and Xuan model respectively. To consider the effect of thermal conductivity, three different models (Maxwell, 1954; Vajjah, 2010; and Sahoo, 2012) have been used. Study revealed that the thermo physical properties of base fluid significantly affects with the graphene nanoparticle suspension.

scholarly journals Dynamic Compression and Thermo-Physical Properties of Some Wood Particles in South Western Nigeria

2017 ◽  
Vol 60 (2) ◽  
pp. 79-84
Author(s):  
Mathew Adefusika Adekoya ◽  
Sunday Samuel Oluyamo ◽  
Olawale Ramon Bello
Keyword(s):  
Heat Capacity ◽  
Physical Properties ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Dynamic Compression ◽  
Dependent Model ◽  
Specific Heat Capacities ◽  
Temperature Dependent Model ◽  
Thermal Diffusivities ◽  
Thermo Physical Properties

This study examines the dynamic compression and thermo-physical properties of some woodparticles obtained from Akure, south local government area, Ondo State, South Western Nigeria. Thesewood particles are of the species of Celtis zenkeri and Celtis philippensis of the Ulmaceae family. Thesamples were possessed into different particle sizes (300, 600 and 850 µm) and subjected to variedcompacting pressures (2.6-3.0 MPa). The density and specific heat capacity of the wood samples weredetermined using weighing displacement methods and temperature dependent model while the thermaldiffusivity was estimated from other thermal properties. The results revealed significant variation in thevalues of the specific heat capacity as a result of change in pressure for all the wood samples considered.The density of wood samples lies between 4.51×102 -7.32×102 kg/m3 and the specific heat capacity valuesobtained for the samples fall within the range of 1.28×103-1.33×103 J/kg/K. It was also noted that thethermal diffusivity obtained falls within the range of 1.37×10-7-2.10×10-7 m2/s for the wood materialsconsidered. However, the values of the densities, specific heat capacities and thermal diffusivities of thesamples were found to change as the compacting pressure increased due to decreased in porosity. Theimplication of the study is that the mate

scholarly journals Investigation on Thermo-physical Properties of L-Valinium Picrate Single Crystal for Modern Applications

2021 ◽  
Author(s):  
M Manivannan ◽  
S. Balachandar ◽  
M. Jose ◽  
S A Martin Britto Dhas
Keyword(s):  
Heat Capacity ◽  
Thermal Diffusivity ◽  
Physical Properties ◽  
Single Crystal ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Thermal Effusivity ◽  
X Ray Diffraction ◽  
X Ray ◽  
Thermo Physical Properties

Abstract Good quality L-valinium picrate single crystal was grown by slow evaporation technique. The lattice parameters of the crystal were measured by single crystal X-ray diffraction analysis. The High resolution X-ray diffraction study reveals good crystalline perfection of the grown crystals. The thermal diffusivity and specific heat capacity were experimentally measured using photoacoustic technique and standard DSC technique, respectively. The thermo physical properties such as thermal conductivity, thermal diffusivity, specific heat capacity, volumetric specific heat capacity, and thermal effusivity of LVP are reported for the first time at ambient temperature.

Enhanced Specific Heat Capacity of Molten Salts Using Organic Nanoparticles

2011 ◽  
Author(s):  
Byeongnam Jo ◽  
Debjyoti Banerjee
Keyword(s):  
Heat Capacity ◽  
Physical Properties ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Organic Nanoparticles ◽  
Energy Applications ◽  
Energy Demands ◽  
Liquid Phases ◽  
Graphite Nanoparticles ◽  
Thermo Physical Properties

In this study we explore the material properties of carbonate salt eutectics that melt at high temperatures (exceeding 480 °C). These salt eutectics demonstrated anomalous enhancement in the specific heat capacity in both solid and liquid phases — when mixed with carious organic nanoparticles such as carbon nanotubes (CNT) and graphite nanoparticles. Theses experimental measurements are compared with previous reports in the literature for exploring the effect of the synthesis protocol on the resulting thermo-physical properties of these nanomaterials. The enhancement of the thermo-physical properties on mixing with nanoparticles is of significant interest in reducing the cost of thermal energy storage (TES) devices and systems. TES can be utilized for levelizing peaks in cyclical energy demands (or duties) that is typical of renewable energy applications where the input energy source may be intermittent (e.g., solar thermal); as well as in geothermal and nuclear energy applications.

Experimental Study of the Effect of Nanoparticle Concentration on Thermo-Physical Properties of Molten Salt Nanofluids

2019 ◽  
Author(s):  
Hani Tiznobaik ◽  
Donghyun Shin
Keyword(s):  
Heat Capacity ◽  
Physical Properties ◽  
Specific Heat ◽  
Molten Salt ◽  
Specific Heat Capacity ◽  
Molten Salts ◽  
Power Plants ◽  
Nanoparticles Concentration ◽  
Thermo Physical Properties

Abstract Increased in thermo-physical properties of molten salt nanofluids have been reported. These findings makes molten salts nanofluids one of the most promising thermal energy storage media. One of the main application of these types of materials are in concentrated solar power plants. In this study, an investigation is performed on nanofluids specific heat capacity mechanisms in order to provide a reasonable description of the specific heat capacity enhancement of nanofluids. Then, a comprehensive experiments are performed on the effects of nanoparticles concentration on the specific heat capacity and materials characterization of molten salt nanofluids. This study is performed to analyze the optimum amount of nanoparticle and find the way to maximize the effects of nanoparticle on thermophysical properties of molten slat. Different molten salts nanofluids with varying nanoparticles concentration were synthesized. The specific heat capacities of mixtures were measured by a modulated scanning calorimeter. Moreover, the material characterization analyses were performed using scanning electron microscopy to investigate the micro-structural characterization of different nanofluids.

scholarly journals Influence of alkaline modification on selected properties of banana fiber paperbricks

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Abayomi A. Akinwande ◽  
Adeolu A. Adediran ◽  
Oluwatosin A. Balogun ◽  
Oluwaseyi S. Olusoju ◽  
Olanrewaju S. Adesina
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Moisture Absorption ◽  
Water Volume ◽  
Banana Fiber ◽  
Fiber Loading ◽  
Banana Fibers ◽  
Alkaline Modification

AbstractIn a bid to develop paper bricks as alternative masonry units, unmodified banana fibers (UMBF) and alkaline (1 Molar aqueous sodium hydroxide) modified banana fibers (AMBF), fine sand, and ordinary Portland cement were blended with waste paper pulp. The fibers were introduced in varying proportions of 0, 0.5, 1.0 1.5, 2.0, and 2.5 wt% (by weight of the pulp) and curing was done for 28 and 56 days. Properties such as water and moisture absorption, compressive, flexural, and splitting tensile strengths, thermal conductivity, and specific heat capacity were appraised. The outcome of the examinations carried out revealed that water absorption rose with fiber loading while AMBF reinforced samples absorbed lesser water volume than UMBF reinforced samples; a feat occasioned by alkaline treatment of banana fiber. Moisture absorption increased with paper bricks doped with UMBF, while in the case of AMBF-paper bricks, property value was noted to depreciate with increment in AMBF proportion. Fiber loading resulted in improvement of compressive, flexural, and splitting tensile strengths and it was noted that AMBF reinforced samples performed better. The result of the thermal test showed that incorporation of UMBF led to depreciation in thermal conductivity while AMBF infusion in the bricks initiated increment in value. Opposite behaviour was observed for specific heat capacity as UMBF enhanced heat capacity while AMBF led to depreciation. Experimental trend analysis carried out indicates that curing length and alkaline modification of fiber were effective in maximizing the properties of paperbricks for masonry construction.

The Key Factors of Low-Frequency Electric Heating Assisted Depressurization Method in the Exploiting of Methane Hydrate Sediments

2021 ◽  
Author(s):  
Ermeng Zhao ◽  
Jian Hou ◽  
Yunkai Ji ◽  
Lu Liu ◽  
Yongge Liu ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Low Frequency ◽  
Electric Heating ◽  
Gas Production ◽  
Hydrate Decomposition ◽  
Hydrate Saturation ◽  
Production Behavior

Abstract Natural gas hydrate is widely distributed in the permafrost and marine deposits, and is regarded as an energy resource with great potential. The low-frequency electric heating assisted depressurization (LF-EHAD) has been proven to be an efficient method for exploiting hydrate sediments, which involves complex multi-physics processes, i.e. current conduction, multiphase flow, chemical reaction and heat transfer. The physical properties vary greatly in different hydrate sediments, which may profoundly affect the hydrate decomposition in the LF-EHAD process. In order to evaluate the influence of hydrate-bearing sediment properties on the gas production behavior and energy utilization efficiency of the LF-EHAD method, a geological model was first established based on the data of hydrate sediments in the Shenhu Area. Then, the influence of permeability, porosity, thermal conductivity, specific heat capacity, hydrate saturation and hydrate-bearing layer (HBL) thickness on gas production behavior is comprehensively analyzed by numerical simulation method. Finally, the energy efficiency ratio under different sediment properties is compared. Results indicate that higher gas production is obtained in the high-permeability hydrate sediments during depressurization. However, after the electric heating is implemented, the gas production first increases and then tends to be insensitive as the permeability decreases. With the increasing of porosity, the gas production during depressurization decreases due to the low effective permeability; while in the electric heating stage, this effect is reversed. High thermal conductivity is beneficial to enhance the heat conduction, thus promoting the hydrate decomposition. During depressurization, the gas production is enhanced with the increase of specific heat capacity. However, more heat is consumed to increase the reservoir temperature during electric heating, thereby reducing the gas production. High hydrate saturation is not conducive to depressurization because of the low effective permeability. After electric heating, the gas production increases significantly. High HBL thickness results in a higher gas production during depressurization, while in the electric heating stage, the gas production first increases and then remains unchanged with the increase of thickness, due to the limited heat supply. The comparison results of energy efficiency suggest that electric heating is more advantageous for hydrate sediments with low permeability, high porosity, high thermal conductivity, low specific heat capacity, high hydrate saturation and high HBL thickness. The findings in this work can provide a useful reference for evaluating the application of the LF-EHAD method in gas hydrate sediments.

Sign in / Sign up

Export Citation Format

Share Document