scholarly journals Effects of various processing parameters on the mechanical properties of sisal fiber/PES composites produced via selective laser sintering

BioResources ◽  
2020 ◽  
Vol 15 (3) ◽  
pp. 5710-5724
Author(s):  
Aboubaker I. B. Idriss ◽  
Jian Li ◽  
Yangwei Wang ◽  
Yanling Guo ◽  
Elkhawad A. Elfaki
Keyword(s):  
Mechanical Strength ◽  
Laser Power ◽  
Low Cost ◽  
Selective Laser Sintering ◽  
Scanning Speed ◽  
Processing Parameters ◽  
Laser Sintering ◽  
Sisal Fiber ◽  
Preheating Temperature ◽  
Scan Speed

A new type of sustainable material, i.e., a sisal fiber/poly-ether sulfone composite (SFPC), which is energy-efficient, environmentally friendly, and has a low cost, was developed for laser sintering additive manufacturing. This study was performed to explore the effects of the processing parameters on the SFPC composite parts produced via selective laser sintering (SLS). The effects of the laser sintering processing parameters, i.e., the preheating temperature, laser power, and scan speed, were studied. Bending and tensile testing of the SFPC specimens was successfully performed via SLS. The effect of the processing parameters on the SLS in terms of the mechanical strength of the laser-sintered parts was investigated. The results determined that the processing parameters had a significant effect on the mechanical strength of the sintered SFPC parts. When the preheating temperature and laser power were increased in the processing SLS system, the mechanical strength of the sintered SFPC parts was significantly increased. However, the scanning speed had an inverse proportional relationship to the mechanical strength of the SFPC SLS parts.

Sintering quality and parameters optimization of sisal fiber/PES composite fabricated by selective laser sintering (SLS)

2020 ◽  
pp. 089270572093917
Author(s):  
Aboubaker IB Idriss ◽  
Jian Li ◽  
Yanling Guo ◽  
Yangwei Wang ◽  
Xingdong Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Process Parameters ◽  
Laser Power ◽  
Selective Laser Sintering ◽  
Scanning Speed ◽  
Laser Sintering ◽  
Sisal Fiber ◽  
Optimum Parameters ◽  
Preheating Temperature

This article aims to improve the sintering quality of the sisal fiber/poly-(ether sulfone) (PES) composite (SFPC) part fabricated via selective laser sintering (SLS). The sisal fiber and PES powders were proposed as the feedstock of the SFPC powder bed for SLS. An orthogonal experimental methodology with four levels and five factors was applied to optimize the process parameters for the single-layer sintering experiment. The mechanical properties and accurate dimensions of the sintered part were tested using a universal testing machine and Vernier caliper. The preheating temperature, scanning speed, and laser power were selected as influencing factors on the mechanical properties and accuracy dimensions of the SFPC part. Furthermore, the influence factors on the quality of the sintered part were studied and analyzed. Additionally, the synthesis weighted scoring method was used to determine the optimum parameters of the SLS part. The results showed that the optimal parameters (factors) were preheating temperature of 82°C, scanning speed of 2 m s−1, laser power of 14 W, and laser wavelength of 10.6 μm. Thus, the quality of SFPC part was significantly enhanced when the optimum parameters were applied in SLS process. This article provided the main reference value for the choice of the process parameters of the biomass composite.

Indirect Selective Laser Sintering of 316L Powder and the Properties of the Parts

2015 ◽  
Vol 775 ◽  
pp. 209-213
Author(s):  
Nai Fei Ren ◽  
Ya Hui Hang ◽  
Yan Zhao ◽  
Qi Yu Yang
Keyword(s):  
Compressive Strength ◽  
Laser Power ◽  
Selective Laser Sintering ◽  
Influence Factors ◽  
Scanning Speed ◽  
Laser Sintering ◽  
Sintering Process ◽  
Range Analysis ◽  
Preheating Temperature ◽  
Molded Parts

During selective laser sintering process, different sintering parameters have great impact on the performance of the molded parts, and the degree of influence is different. Using orthogonal test, indirect sintered 316L stainless steel, the compressive strength and precision of the parts were measured and compared to study the influence of various sintering parameters (laser power, scanning speed, scan spacing, preheating temperature) on sintering. The greater degree of influence factors were got by range analysis. The results show that laser power, scanning speed and scan spacing have greater degree of influence on the compressive strength of the parts, and the preheating temperature have less impact. By comparison, the optimum set of parameters was concluded: the laser power is 15W, the scanning speed is 1900mm/s, the scan spacing is 0.125mm, and the preheating temperature is 60°C.

The Optimization Design Study of Selective Laser Sintering Process Parameters on the Pro-Coated Sand Mold

2011 ◽  
Vol 55-57 ◽  
pp. 853-858
Author(s):  
Rong Cheng ◽  
Xiao Yu Wu ◽  
Jian Ping Zheng
Keyword(s):  
Layer Thickness ◽  
Process Parameters ◽  
Laser Power ◽  
Selective Laser Sintering ◽  
Dimensional Accuracy ◽  
Processing Parameters ◽  
Laser Sintering ◽  
Process Variables ◽  
Scan Speed ◽  
Coated Sand

This paper presents experimental investigations on influence of important process parameters viz., laser power, scan speed, layer thickness, hatching space along with their interactions on dimensional accuracy of Selective Laser Sintering (SLS) processed pro-coated sand mold. It is observed that dimensional error is dominant along length and width direction of built mold. Optimum parameters setting to minimize percentage change in length and width of standard test specimen have been found out using Taguchi’s parameter design. Optimum process conditions are obtained by analysis of variance (ANOVA) is used to understand the significance of process variables affecting dimension accuracy. Scan speed and hatching space are found to be most significant process variables influencing the dimension accuracy in length and width. And laser power and layer thickness are less influence on the dimension accuracy. The optimum processing parameters are attained in this paper: laser power 11 W; scan speed 1200 mm/s; layer thickness 0.5 mm and hatching space 0.25 mm. It has been shown that, on average, the dimensional accuracy under this processing parameters combination could be improved by approximately up to 25% compared to other processing parameters combinations.

scholarly journals Selective laser sintering and post-processing of sisal fiber/ poly-(ether sulfone) composite powder

BioResources ◽  
2020 ◽  
Vol 15 (1) ◽  
pp. 1338-1353
Author(s):  
Jian Li ◽  
Aboubaker I. B. Idriss ◽  
Yanling Guo ◽  
Yangwei Wang ◽  
Zhiqiang Zhang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Strength ◽  
Composite Powder ◽  
Selective Laser Sintering ◽  
Testing Machine ◽  
Single Layer ◽  
Processing Parameters ◽  
Laser Sintering ◽  
Sisal Fiber ◽  
Post Processing

Selective Laser Sintering (SLS) technology can be utilized to recycle residues from forestry and agriculture, thereby alleviating shortages of materials and reducing energy consumption by producing wood-plastic pieces for industrial application. The mechanical strength of wood-plastic SLS parts is low, which restricts the application of this technology. In this study, a novel type of sisal fiber/poly-(ether sulfone) (PES) composite was prepared using a polymer mixing method in order to improve the mechanical properties of SLS parts. Single-layer sintering method was adopted to determine the proper processing parameters. The mechanical properties of the parts with different ingredient ratios and different particle sizes of sisal fiber before and after post-processing were tested using a universal testing machine. The morphology was examined using scanning electron microscopy (SEM). Results showed that the mechanical properties of the printed parts were relatively enhanced; when the mixing ratio of composite powder was 10/90 wt/wt. In addition, the part fabricated by powder of particles size less than 0.105 mm (0.125 mm ≥ PS < 0.105mm) had the best mechanical strength. Moreover, the post-wax treatment significantly improved the strength of the parts, and the surfaces became smoother.

Research on Warpage of Polystyrene in Selective Laser Sintering

2010 ◽  
Vol 43 ◽  
pp. 578-582 ◽  
Author(s):  
C.Y. Wang ◽  
Q. Dong ◽  
X.X. Shen
Keyword(s):  
Layer Thickness ◽  
Process Parameters ◽  
Laser Power ◽  
Selective Laser Sintering ◽  
Scanning Speed ◽  
Laser Sintering ◽  
Main Process ◽  
Influence Of Process Parameters ◽  
Temperature Changes ◽  
Hatch Spacing

Warpage is a crucial factor to accuracy of sintering part in selective laser sintering (SLS) process. In this paper, The influence of process parameters on warpage when sintering polystyrene(PS) materials in SLS are investigated. The laser power, scanning speed, hatch spacing, layer thickness as well as temperature of powder are considered as the main process parameters. The results showed that warpage increases with the increase of hatch space. Contary to it, warpage decreases with the increase of laser power. Warpage decreases with the increase of layer thickness between 0.16~0.18mm and changes little with increase of the thickness. Warpage increases along with the increase of scanning speed but decreases when the speed is over about 2000mm/s. When the temperature changes between 82°C-86°C, warpage decreases little with the increase of temperature. But further increase of temperature leads to warpage decreasing sharply when the temperature changes between 86°C-90°C.

Study on the Forming Accuracy and Density of Eucalyptus/PES Fabricated by Laser Sintering

2015 ◽  
Vol 667 ◽  
pp. 200-205
Author(s):  
Yan Ling Guo ◽  
Yue Qiang Yu ◽  
Kai Yi Jiang
Keyword(s):  
Layer Thickness ◽  
Laser Power ◽  
Dimensional Accuracy ◽  
Processing Parameters ◽  
Variable Density ◽  
Laser Sintering ◽  
Powder Size ◽  
Forming Accuracy ◽  
Preheating Temperature ◽  
Forming Precision

. Based on orthogonal test, the forming accuracy and density of laser sintering eucalyptus/PES blend is studied in this paper. It mainly analysed the effect of the powder size and process parameters (such as laser power, layer thickness, preheating temperature, etc) on the forming precision and density of sintered eucalyptus/PES parts, also the correlation analysis of molding error caused by the powder’s physical properties and machine is performed. By measuring the parts’ dimensions, the results show that the laser power and powder size are two main factors influencing parts’ density, and variable density, layer thickness and preheating temperature jointly affect the dimensional accuracy. The optimized processing parameters are obtained. The powder size, laser power, scanning rate, layers thickness and preheating temperature are 300 mesh, 43W, 2000mm/s, 0.1mm, 60°C respectively.

scholarly journals Parametric Study on In Situ Laser Powder Bed Fusion of Mo(Si1−x,Alx)2

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 4849
Author(s):  
T. Minasyan ◽  
S. Aydinyan ◽  
E. Toyserkani ◽  
I. Hussainova
Keyword(s):  
Parametric Study ◽  
Laser Power ◽  
Side Surface ◽  
Scanning Speed ◽  
Processing Parameters ◽  
Powder Bed ◽  
Good Surface ◽  
Melt Pool ◽  
Scan Speed ◽  
Good Surface Finish

Mo(Si1−x,Alx)2 composites were produced by a pulsed laser reactive selective laser melting of MoSi2 and 30 wt.% AlSi10Mg powder mixture. The parametric study, altering the laser power between 100 and 300 W and scan speed between 400 and 1500 mm·s−1, has been conducted to estimate the effect of processing parameters on printed coupon samples’ quality. It was shown that samples prepared at 150–200 W laser power and 400–500 mm·s−1 scan speed, as well as 250 W laser power along with 700 mm·s−1 scan speed, provide a relatively good surface finish with 6.5 ± 0.5 µm–10.3 ± 0.8 µm roughness at the top of coupons, and 9.3 ± 0.7 µm–13.2 ± 1.1 µm side surface roughness in addition to a remarkable chemical and microstructural homogeneity. An increase in the laser power and a decrease in the scan speed led to an apparent improvement in the densification behavior resulting in printed coupons of up to 99.8% relative density and hardness of ~600 HV1 or ~560 HV5. The printed parts are composed of epitaxially grown columnar dendritic melt pool cores and coarser dendrites beyond the morphological transition zone in overlapped regions. An increase in the scanning speed at a fixed laser power and a decrease in the power at a fixed scan speed prohibited the complete single displacement reaction between MoSi2 and aluminum, leading to unreacted MoSi2 and Al lean hexagonal Mo(Si1−x,Alx)2 phase.

Effects of the Processing Parameters on Porosity of Selective Laser Sintered Aliphatic Polycarbonate

2014 ◽  
Vol 915-916 ◽  
pp. 1000-1004 ◽  
Author(s):  
Xiao Hui Song ◽  
Yu Sheng Shi ◽  
Ping Hui Song ◽  
Qing Song Wei ◽  
Wei Li
Keyword(s):  
Mechanical Properties ◽  
Biomedical Engineering ◽  
Laser Power ◽  
Orthogonal Experiment ◽  
Selective Laser Sintering ◽  
Processing Parameters ◽  
Laser Sintering ◽  
Optimal Parameters ◽  
Micro Structure ◽  
Aliphatic Polycarbonate

Selective Laser Sintering (SLS) has been successfully and broadly applied in biomedical engineering to fabricated biomedical part. And the porosity and microstructure of part can be controlled by main sintered parameters. This research focused aliphatic Polycarbonate (PC) sintered with SLS. According to the orthogonal experiment, the effect of laser power energy and interaction between main sintered parameters on porosity has been studied. Then the micro structure and mechanical properties of specimens sintered with the best optimal parameters have been analyzed.

scholarly journals Selective Laser Sintering (SLS) and Post-Processing of Prosopis Chilensis/Polyethersulfone Composite (PCPC)

Materials ◽  
2020 ◽  
Vol 13 (13) ◽  
pp. 3034
Author(s):  
Aboubaker I. B. Idriss ◽  
Jian Li ◽  
Yangwei Wang ◽  
Yanling Guo ◽  
Elkhawad A. Elfaki ◽  
...  
Keyword(s):  
Mechanical Strength ◽  
Particle Distribution ◽  
Low Cost ◽  
Selective Laser Sintering ◽  
Single Layer ◽  
Dimensional Accuracy ◽  
Laser Sintering ◽  
Raw Material ◽  
Post Processing ◽  
Prosopis Chilensis

The range of selective laser sintering (SLS) materials is currently limited, and the available materials are often of high cost. Moreover, the mechanical strength of wood–plastic SLS parts is low, which restricts the application of a SLS technology. A new composite material has been proposed to address these issues, while simultaneously valorizing agricultural and forestry waste. This composite presents several advantages, including reduced pollution associated with waste disposal and reduced CO2 emission with the SLS process in addition to good mechanical strength. In this article, a novel and low-cost Prosopis chilensis/polyethersulfone composite (PCPC) was used as a primary material for SLS. The formability of PCPC with various raw material ratios was investigated via single-layer experiments, while the mechanical properties and dimensional accuracy of the parts produced using the various PCPC ratios were evaluated. Further, the microstructure and particle distribution in the PCPC pieces were examined using scanning electron microscopy. The result showed that the SLS part produced via 10/90 (wt/wt) PCPC exhibited the best mechanical strength and forming quality compared to other ratios and pure polyethersulfone (PES), where bending and tensile strengths of 10.78 and 4.94 MPa were measured. To improve the mechanical strength, post-processing infiltration was used and the PCPC-waxed parts were enhanced to 12.38 MPa and 5.73 MPa for bending and tensile strength.

Effect of processing parameters on forming defects during selective laser melting of AlSi10Mg powder

2020 ◽  
Vol 26 (5) ◽  
pp. 871-879 ◽  
Author(s):  
Haihua Wu ◽  
Junfeng Li ◽  
Zhengying Wei ◽  
Pei Wei
Keyword(s):  
Selective Laser Melting ◽  
Laser Power ◽  
Scanning Speed ◽  
Processing Parameters ◽  
Argon Pressure ◽  
Powder Layer ◽  
Laser Melting ◽  
Content Type ◽  
Scan Speed ◽  
Forming Defects

Purpose To fabricate a selective laser melting (SLM)-processed AlSi10Mg part with almost full density and free of any apparent pores, this study aims to investigate the effect of ambient argon pressure and laser scanning speed on the particles splash during the AlSi10Mg powder bed laser melting. Design/methodology/approach Based on the discrete element method (DEM), a 3D model of random distribution of powder particles was established, and the 3D free surface of SLM forming process was dynamically tracked by the volume of fluid, where a Gaussian laser beam acts as the energy source melting the powder bed. Through the numerical simulation and process experimental research, the effect of the applied laser power and scanning speed on the operating laser melting temperature was studied. Findings The process stability has a fundamental role in the porosity formation, which is process-dependent. The effect of the processing conditions on the process stability and the resultant forming defects were clarified. Research limitations/implications The results shows that the pores were the main defects present in the SLM-processed AlSi10Mg sample, which decreases the densification level of the sample. Practical implications The optimal processing parameters (argon pressure of 1,000 Pa, laser power of 180 W, scan speed of 1,000 mm/s, powder layer thickness of 35 µm and hatch spacing of 50 µm ) applied during laser melting can improve the quality of selective laser melting of AlSi10Mg, Social implications It can provide a technological support for 3D printing. Originality/value Based on the analysis of the pore and balling formation mechanisms, the optimal processing parameters have been obtained, which were argon pressure of 1,000 Pa, laser power of 180 W, scan speed of 1,000 mm/s, powder layer thickness of 35 µm and hatch spacing of 50 µm. Then, a near-fully dense sample free of any apparent pores on the cross-sectional microstructure was produced by SLM, wherein the relative density of the as-built samples is larger than 97.5%.

Sign in / Sign up

Export Citation Format

Share Document