scholarly journals Application of corrosion-resistant corning advanced-flow reactors for multiphase Bunsen reaction-part one: investigation on SO2 absorption 

2019 ◽  
Vol 4 (4) ◽  
pp. 123-136
Author(s):  
Armin Moniri ◽  
Hui Wang ◽  
Xinjun (Eric) Wu
Keyword(s):  
Flow Reactors ◽  
Corrosion Resistant ◽  
So2 Absorption

Physical, Chemical, and Crystallographic Characterization of Anodic Coatings on High Strength Aluminum Base Alloys

1976 ◽  
Vol 34 ◽  
pp. 636-637
Author(s):  
R. E. Herfert ◽  
N. T. McDevitt
Keyword(s):  
Sulfuric Acid ◽  
Salt Spray ◽  
High Strength ◽  
Environmental Stability ◽  
Anodic Films ◽  
Sodium Dichromate ◽  
Corrosion Resistant ◽  
Aerospace Applications ◽  
Bond Strengths ◽  
Adhesive Bonded Joints

Durability of adhesive bonded joints in moisture and salt spray environments is essential to USAF aircraft. Structural bonding technology for aerospace applications has depended for many years on the preparation of aluminum surfaces by a sulfuric acid/sodium dichromate (FPL etch) treatment. Recently, specific thin film anodizing techniques, phosphoric acid, and chromic acid anodizing have been developed which not only provide good initial bond strengths but vastly improved environmental durability. These thin anodic films are in contrast to the commonly used thick anodic films such as the sulfuric acid or "hard" sulfuric acid anodic films which are highly corrosion resistant in themselves, but which do not provide good initial bond strengths, particularly in low temperature peel.The objective of this study was to determine the characteristics of anodic films on aluminum alloys that make them corrosion resistant. The chemical composition, physical morphology and structure, and mechanical properties of the thin oxide films were to be defined and correlated with the environmental stability of these surfaces in humidity and salt spray. It is anticipated that anodic film characteristics and corrosion resistance will vary with the anodizing processing conditions.

Could biomass-fueled boilers be operated at higher steam temperatures? Part 3: Initial analysis of costs and benefits

TAPPI Journal ◽  
2014 ◽  
Vol 13 (8) ◽  
pp. 65-78 ◽  
Author(s):  
W.B.A. (SANDY) SHARP ◽  
W.J. JIM FREDERICK ◽  
JAMES R. KEISER ◽  
DOUGLAS L. SINGBEIL
Keyword(s):  
Flue Gas ◽  
Power Plants ◽  
Superheated Steam ◽  
Black Liquor ◽  
Simulation Software ◽  
Operating Conditions ◽  
Costs And Benefits ◽  
Steam Generation ◽  
Fireside Corrosion ◽  
Corrosion Resistant

The efficiencies of biomass-fueled power plants are much lower than those of coal-fueled plants because they restrict their exit steam temperatures to inhibit fireside corrosion of superheater tubes. However, restricting the temperature of a given mass of steam produced by a biomass boiler decreases the amount of power that can be generated from this steam in the turbine generator. This paper examines the relationship between the temperature of superheated steam produced by a boiler and the quantity of power that it can generate. The thermodynamic basis for this relationship is presented, and the value of the additional power that could be generated by operating with higher superheated steam temperatures is estimated. Calculations are presented for five plants that produce both steam and power. Two are powered by black liquor recovery boilers and three by wood-fired boilers. Steam generation parameters for these plants were supplied by industrial partners. Calculations using thermodynamics-based plant simulation software show that the value of the increased power that could be generated in these units by increasing superheated steam temperatures 100°C above current operating conditions ranges between US$2,410,000 and US$11,180,000 per year. The costs and benefits of achieving higher superheated steam conditions in an individual boiler depend on local plant conditions and the price of power. However, the magnitude of the increased power that can be generated by increasing superheated steam temperatures is so great that it appears to justify the cost of corrosion-mitigation methods such as installing corrosion-resistant materials costing far more than current superheater alloys; redesigning biomassfueled boilers to remove the superheater from the flue gas path; or adding chemicals to remove corrosive constituents from the flue gas. The most economic pathways to higher steam temperatures will very likely involve combinations of these methods. Particularly attractive approaches include installing more corrosion-resistant alloys in the hottest superheater locations, and relocating the superheater from the flue gas path to an externally-fired location or to the loop seal of a circulating fluidized bed boiler.

Droplet Factories: Synthesis and Assembly of Silver and Palladium Nanoparticles at the Liquid-Liquid Interface

2019 ◽  
Author(s):  
Suchanuch Sachdev ◽  
Rhushabh Maugi ◽  
Sam Davis ◽  
Scott Doak ◽  
Zhaoxia Zhou ◽  
...  
Keyword(s):  
Iron Oxide ◽  
Reaction Rate ◽  
Tertiary Structure ◽  
Flow Reactor ◽  
Pd Nanoparticles ◽  
Subsequent Removal ◽  
Immiscible Liquids ◽  
Flow Reactors ◽  
Droplet Flow ◽  
One Step

<div>The interface between two immiscible liquids represent an ideal substrate for the assembly of nanomaterials. The defect free surface provides a reproducible support for creating densely packed ordered materials. Here a droplet flow reactor is presented for the synthesis and/ or assembly of nanomaterials at the interface of the emulsion. Each droplet acts as microreactor for a reaction between decamethylferrocene (DmFc) within the hexane and metal salts (Ag+/ Pd2+) in the aqueous phase. The hypothesis was that a spontaneous, interfacial reaction would lead to the assembly of nanomaterials creating a Pickering emulsion. The subsequent removal of the solvents showed how the Ag nanoparticles were trapped at the interface and retain the shape of the droplet, however the Pd nanoparticles were dispersed with no tertiary structure. To further exploit this, a one-step process where the particles are synthesised and then assembled into core-shell materials was proposed. The same reactions were performed in the presence of oleic acid stabilise Iron oxide nanoparticles dispersed within the hexane. It was shown that by changing the reaction rate and ratio between palladium and iron oxide a continuous coating of palladium onto iron oxide microspheres can be created. The same reaction with silver, was unsuccessful and resulted in the silver particles being shed into solution, or incorporated within the iron oxide micro particle. These insights offer a new method and chemistry within flow reactors for the creation of palladium and silver nanoparticles. We use the technique to create metal coated iron oxide nanomaterials but the methodology could be easily transferred to the assembly of other materials.</div><div><br></div>

SANICRO 41

Alloy Digest ◽  
1995 ◽  
Vol 44 (1) ◽  
Keyword(s):  
Corrosion Resistance ◽  
Physical Properties ◽  
Oil And Gas ◽  
High Strength ◽  
Heat Treating ◽  
Gas Production ◽  
Oil And Gas Production ◽  
Corrosion Resistant ◽  
Corrosion Resistant Alloy ◽  
Nickel Base

Abstract SANDVIK SANICRO 41 is a nickel-base corrosion resistant alloy with a composition balanced to resist both oxidizing and reducing environments. A high-strength version (110) is available for oil and gas production. This datasheet provides information on composition, physical properties, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, and joining. Filing Code: Ni-475. Producer or source: Sandvik.

Sign in / Sign up

Export Citation Format

Share Document