scholarly journals Investigation of hydrogeomechanical parameters of loess massifs in conditions of technogenic underflooding and development of technical recommendations for strengthening of bases of foundations

2019 ◽  
Vol 28 (1) ◽  
pp. 173-179 ◽  
Author(s):  
I. O. Sadovenko ◽  
A. M. Puhach ◽  
N. I. Dereviahina
Keyword(s):  
Strain State ◽  
Quantitative Estimation ◽  
Residential Buildings ◽  
Finite Element Approximation ◽  
Element Approximation ◽  
Soil Base ◽  
Stress Strain ◽  
Elastic Mode ◽  
Stress Strain State ◽  
Water Saturated

Based on the analysis of actual data and the results of numerical modeling, dependencies of deformations of the investigated residential complex due to technogenic moistening of a loess massif of soils are investigated. It was established that a dynamics of subsidence of bench marks in time is closely correlated with a moistening mode. In order to form a picture of dynamics of development of moistening phases of the massif and a quantitative estimation of main factors of their formation, a numerical model of the loess massif was built, based on the finite element approximation of the section of built-up area of the residential complex. Stability of a soil massif was estimated by the character of development of plastic deformation zones. Analysis of a stress-strain state of a rock massif indicated that water-saturated soils are partially in a state of plastic flow in a base. The development of shear deformations is most characteristic within a zone of the main moistening, as well as a boundary of its front. Development of rupture disturbances at the edge of the contour of buildings corresponds with the formation of tear cracks. An intensification of subsidence of buildings with simultaneous frontal and subvertical technogenic moistening of loess soils can be noted. Model estimations of a stress-strain state of the pile foundation, considering the uneven subsidence that occurred along the perimeter of residential buildings, show that the elastic mode of their deformation has not been exhausted. Options of redistribution of loads from residential sections onto an additional pile field, regulated base moistening and grouting of soils are considered as engineering measures to prevent further deformation of the residential complex. Stabilization of a soil base by means of high-pressure cementation is the most acceptable in the present conditions. Technological scheme of cementation of the soil base is recommended, as well as measures after the base stabilization, such as monitoring of further deformations of the complex itself and parking structures, and possibilities of constructing auxiliary drainage.

scholarly journals Research of stress-strain state and stability of a rokfill dam under seismic actions

Vestnik MGSU ◽  
2015 ◽  
pp. 157-166
Author(s):  
Vyacheslav Valentinovich Orekhov
Keyword(s):  
Strain State ◽  
Initial Conditions ◽  
The Body ◽  
Cohesionless Soil ◽  
Soil Base ◽  
Stress Strain ◽  
Stress Strain State ◽  
Soil Skeleton ◽  
Water Saturated ◽  
Seismic Impacts

One of the main factors determining the safety of earth sea and river hydraulic structures erected on water-saturated grounds is the process of consolidation, manifested under the action of static and seismic loads. A feature of cohesionless soils located in the structure itself or in its base, is their potential ability to liquefaction under seismic impacts. This paper describes the method of calculating the saturated soil’s environments under seismic actions based on the numerical solution of differential equations of the theory of consolidation by finite element method. The results of the static problem solving for the phased construction of the installation are used as the initial conditions. In order to describe the deformability of soil materials mathematical model formed by the theory of plastic flow with hardening is used. The parameters of this model are determined by the results of triaxial testing of soils. As an example, we study the interaction of a sea rockfill dam with a sandy base under seismic impacts, determined by the synthetic accelerograms. The results of calculations of the stress-strain state of the two sections of the dam (shallow and deep) are presented, and assessment is made of the possibility of liquefaction of sandy soil base. It is shown that the pore pressure that occurs in water-saturated cohesionless soil base and the body of the dam under seismic impacts, unloads the soil skeleton, which leads to a decrease in local shear safety factors. And, in the less dense soil base of the shallow section of the dam, the soil skeleton is unloaded to a greater extent, which negatively affects its overall safety factor.

scholarly journals Settlement and bearing capacity of water-saturated soils of foundations of finite width under static impact

Vestnik MGSU ◽  
2021 ◽  
pp. 463-472
Author(s):  
Zaven G. Ter-Martirosyan ◽  
Armen Z. Ter-Martirosyan ◽  
Ahmad Othman
Keyword(s):  
Bearing Capacity ◽  
Strain State ◽  
Water Saturation ◽  
Strength Properties ◽  
Finite Width ◽  
Stress Strain ◽  
Linear Deformation ◽  
Stress Strain State ◽  
Linear And Nonlinear ◽  
Water Saturated

Introduction. In case of brief exposure to static loads or dynamic loads, in conditions of absence of drainage, distribution of total stresses between the skeleton of soil and pore gas-containing water should be taken in account. The situation of the stress-strain state of the base is further complicated when we consider the degree of water-saturation of soil of the foundation (0.8 < Sr ≤ 1). The aim of the study is to pose and solve problem of the stress-strain state of a water-saturated soil massif, Including settlement and bearing capacity of a water-saturated base of a foundation of finite width, depending on the degree of water saturation of soils, taking into account the linear and nonlinear properties of the skeleton of soil and the compressibility of pore gas-containing water. Materials and methods. Henckyʼs system of physical equations are used as a calculation model to describe the relationship between deformation and stresses of soil, which takes into account the influence of the average stress on the deformation and strength properties of the soil. This system allows us to represent the linear deformation of the soil as the sum of the volumetric and shear components of the soil of this deformation. In addition allows us too to determine the deformation of the layer of soil, as part of the compressible thickness of the base of foundation with finite width under conditions of free deformations. Results. Depending on the linear and nonlinear deformation parameters, the settlement can be developed with a damped curve (S – p) and stabilize, and can be developed with a non-damped curve (S – p) and moved to the stage of progressive settlement. Conclusions. Solutions have been made for cases when the water-saturation of the base soils changes in the range of 0.8 to 1.0. It is shown that the settlement and bearing capacity of a water-saturated base significantly depends on the degree of water saturation of soils.

scholarly journals Influence of house bearing construction rigidi-ty of precast reinforced concrete on stress-strain state Continuous Flight Auger (CFA) piles foundations

2020 ◽  
pp. 48-57
Author(s):  
Viktor Nosenko ◽  
Oleg Krivenko
Keyword(s):  
Reinforced Concrete ◽  
Strain State ◽  
Residential Buildings ◽  
Precast Concrete ◽  
Relative Deformation ◽  
Construction Time ◽  
Stress Strain ◽  
Stress Strain State ◽  
Basement Floor ◽  
The Difference

At present, the tendency to build multi-storey residential buildings has become widespread in Ukraine. This is due to a number of reasons: significant increase in land prices in cities, dense urban development and the availability of appropriate equipment for the construction of such structures. One of the most common materials for multi-storey buildings is monolithic reinforced concrete. The main advantage of monolithic structures is the possibility of free spatial planning and the possibility of uniform redistribution of forces in the elements of the frame - the house works as one rigid entire structure. On the other hand, such structures require a long construction time and appropriate highly qualified control of monolithic works. Therefore, as an alternative, prefabricated reinforced concrete structures are used to accelerate the pace of construction. In this work, the influence of the rigidity of a precast reinforced concrete house on the stress-strain state of CFA piles foundation is investigated. The stress-strain state of a precast reinforced concrete building with two basement options is analyzed: precast and monolithic.                                                 The numerical modeling of the interaction of the system elements is used as a research method: soil base - foundation - aboveground structure. It was found that the replacement in a prefabricated house only one basement floor of precast concrete on a monolithic one affects the redistribution of forces, so the self-supporting wall is loaded 2.6 times, and the busiest wall, which rests on both sides of the floor slab, is unloaded to 2.1 times.  It was found that in the case of a basement made of precast reinforced concrete with a precast basement the difference efforts in pile heads (under the load-bearing walls) can differ 1.98 times, and in the case of a monolithic one 1.17 times. So it is mean, the monolithic foundation redistributed of efforts between the piles is more uniform. It is established that the monolithic reinforced concrete basement, in comparison with the prefabricated one, reduces the uneven settlement of the foundation by 2.4 times. When designing large-panel houses, it is advisable to provide a basement floor monolithic - this will allow to load the fundamental constructions more evenly, which in its reduction reduces the relative deformation of buildings and reduces their cost.

scholarly journals Stress-strain state of the building foundations with taking into account the possible water saturation of loess soils

2020 ◽  
pp. 22-31
Author(s):  
Veronika Zhuk ◽  
Oleksandr Piatkov ◽  
Sergiy Tarambula
Keyword(s):  
Strain State ◽  
Water Saturation ◽  
Cost Effective ◽  
Loess Soil ◽  
Soil Base ◽  
Stress Strain ◽  
Engineering Structures ◽  
Load Bearing ◽  
Stress Strain State ◽  
Loess Soils

In Ukraine, the problem of construction on loess soils is relevant due to the widespread use of these soils and their negative property - the ability to give additional deformations of subsidence during water saturation. Flooding of territories by groundwater, emergency leaks from aquifers cause significant problems during the exploitation of buildings and engineering structures on such soils. Computer simulation of the interaction of the building with the soil base allows to investigate the influence of all negative factors on the change of the stress-strain state of both the soil base and the load-bearing structures of the building. The study of the interaction of the building with the foundation was performed using the software package LIRA-CAD. The interaction of the building with the soil base, the soils of which are able to reduce their mechanical properties with increasing humidity and give additional subsidence deformations, was studied. A variant design of the foundations was performed taking into account the occurrence of uneven deformations during subsidence of the loess soil due to its moistening in case of possible emergency losses from aquifers. The change of stress-strain state of the foundations of the building depending on the spatial rigidity of the foundation, the location of the soaking zone within the building spot, the shape and size of the zone of soil moisture is analyzed. It is shown that taking into account the possible water saturation of loess soils when calculating the collaborate of the building with the soil base, allows to obtain stress-strain state of foundations and load-bearing structures of the aboveground part of the building for the most unfavorable conditions that may occur. The search for the optimal variant of the foundation structures of the building, which, while remaining cost-effective, provides reliable operation of the building in conditions of possible occurrence of uneven deformations of subsidence of the soil base during water saturation of the layer of loess soils. According to the research results, a rational variant of the foundation structures has been designed taking into account the possible occurrence of non-uniform deformations.  

scholarly journals Influence of the sequence of erection of build-ings on the formation of the stress-strain state of the system «base-foundation-overhead structures»

2020 ◽  
pp. 32-44
Author(s):  
Liudmyla Skochko ◽  
Artem Shabaltun
Keyword(s):  
Strain State ◽  
Design Parameters ◽  
Soil Base ◽  
Stress Strain ◽  
High Rise ◽  
Stress Strain State ◽  
Subsequent Section ◽  
The Impact ◽  
Ground Structures ◽  
Formulation Of Problems

The influence of the order of construction of houses on the formation of the stress-strain state of the system "foundation-foundation-above-ground structures" is investigated For this purpose, several options for setting tasks for the phased construction of multi-section building sections are considered. With this in mind, it should be noted that the construction of each subsequent section has an impact on the built entirely or partially adjacent section. That is why this effect should be investigated to predict how serious this impact may be, and to draw appropriate constructive decisions. Thus, the main objectives of the study are: Creation of SEM without taking into account the stages of construction of the house; Calculation of a house with a phased loading of 5 floors. Taking into account changes in the order of construction of sections; Formation of SEM taking into account the sequence of erection of sections without including the sequence of erection of floors within the boundaries of the current section; Research of the impact of the calculation of sections of a multi-section building without and taking into account the summary of subsequent sections. The research of the impact of the sequence of construction and installation of the object will allow us to assess the stress-strain scheme at all stages of construction, so changes in the behavior of the scheme will be recorded at all stages of construction specified by the designers. To do this, the change in the stress-strain state (VAT) of the system "foundation - foundations - above-ground structures" must be modeled with different options for stages of construction, taking into account the real parameters of the soil base and so on. The interaction of piles in different zones of sections, the work of grids in the foundations of high-rise buildings are considered. The research was carried out with the help of numerical modeling of the system "foundation - foundations - aboveground constructions". The redistribution of forces in the piles depending on the formulation of problems on the stages of construction of sections and design parameters (location of piles in characteristic zones, the influence of the stiffness of the aboveground part on the redistribution of forces). Characteristic zones in the foundation are distinguished: they are central, lateral, angular and especially at the joints of adjacent sections. The redistribution of efforts between piles and a grid is revealed.  

scholarly journals The stressstrain state of low-head dams’ basis on stratified soil

2016 ◽  
Vol 3 ◽  
pp. 4-9
Author(s):  
Paluanov D.T.
Keyword(s):  
Hydrostatic Pressure ◽  
Strain State ◽  
Soil Base ◽  
Stress Strain ◽  
Stress Strain State ◽  
Low Head ◽  
Calculated Model

This article is considered stress-strain state of low-head dams’ basis on stratified soil. The peculiarities of construction of low-head dams on stratified soils are resulted. The calculated model for the solution of the stress-strain state of low-head dams’ basis is resulted. The calculations of the stress-strain state of soil base under the weight of the constructions and the hydrostatic pressure of water the upstream dam are established.

scholarly journals Experimental study of thermomechanical effects in water-saturated limestones during their deformation

2021 ◽  
Vol 247 ◽  
pp. 1-10
Author(s):  
Dmitry Blokhin ◽  
Pavel Ivanov ◽  
Oleg Dudchenko
Keyword(s):  
Thermal Radiation ◽  
Strain State ◽  
Water Saturation ◽  
Stability Control ◽  
Stress Strain ◽  
Stress Strain State ◽  
Water Saturated ◽  
Solid Bodies ◽  
Non Destructive ◽  
Stone Structures

Stability control of elements of stone constructions of various structures is a prerequisite for their safe operation. The use of modern methods of non-destructive diagnostics of the stress-strain state of such constructions is an effective, and in many cases the only way to control it. Studies of thermal radiation accompanying the processes of solid bodies deformation allowed to justify and develop a method that allows to obtain non-contact information about changes in the stress-strain state in various types of geomaterials, including limestones. However, studies of the water saturation influence of rocks on the thermal radiation parameters recorded in this way are currently superficial. Taking into account the water saturation degree of rocks is necessary when monitoring the mechanical condition of stone structures that are in direct contact with water. The main purpose of this work is to study the dependences of changes in the intensity of thermal radiation from the surface of limestone samples with different humidity under conditions of uniaxial compression. The obtained results showed the expected significant decrease in the mechanical properties (uniaxial compressive strength and elastic modulus) of water-saturated samples in comparison with dry ones. At the same time, a significant increase in the intensity of thermal radiation of limestone samples subjected to compression with an increase in their water saturation was recorded, which makes it necessary to take into account the revealed regularity when identifying changes in the stress state of stone structures established according to non-contact IR diagnostics in real conditions.

scholarly journals Calculation of large-span glulam structures as a soil base-foundation-above-ground structure system

ScienceRise ◽  
2021 ◽  
pp. 17-23
Author(s):  
Denys Mykhailovskyi ◽  
Tetіana Sklіarova
Keyword(s):  
Cross Section ◽  
Strain State ◽  
Soil Base ◽  
Ground Structure ◽  
Stress Strain ◽  
Large Span ◽  
Stress Strain State ◽  
Long Span ◽  
The Cross ◽  
Scientific Results

The object of research. Long-span glulam arches are widely used as coatings for public and sports buildings. The studies carried out concern double-hinged segmental arches with spans of 60 m and more. Description of the problem. The study of the peculiarities of the work of arches as a system "soil base - foundation - above-ground structure" is associated with the significant influence of uneven deformations of supports on the stress-strain state of the above-ground structure. A change in the stress-strain state in the structure itself, associated with uneven deformations of the foundations, can lead to a significant decrease up to the complete exhaustion of the bearing capacity Main scientific results. This article provides an analysis of the change in the stress-strain state of glulam arches when calculating the system "soil base-foundation-above-ground structure". It is noted that non-uniform deformations of supports have the greatest influence on the stress in the support zones of the structure. The range of critical non-uniform subsidence has been determined, which should be limited when calculating and designing the foundations of large-span arches. It has been confirmed that double-hinged glulam arches work well in conditions of uneven subsidence due to the peculiarities of the design scheme. The results of the studies carried out and the recommendations provided will significantly improve the reliability of large-span structures and require mandatory inclusion in the current practice of calculation and design. In addition, additional requirements for the distance between mine workings for large-span structures should be introduced when performing engineering and geological surveys. This distance should be reduced for a clearer account of the deformability of the foundations for columnar foundations, and the number of workings should be increased. The area of practical use of the research results. The cross-section of the glulam arches is selected taking into account additional deformations of the supports, making it possible to avoid unpredictable damage to the structure during operation. Innovative technological product. Glulam arches, the cross-section of which is determined taking into account additional deformations from uneven subsidence of the supports Scope of application. Glulam arches calculated in this way can be used as covering for public and sports buildings for various purposes.

Sign in / Sign up

Export Citation Format

Share Document