Reliability Studies on Ge High Density Interconnect (Hdi) Modules

1993 ◽  
Vol 323 ◽  
Author(s):  
Kyung W. Paik ◽  
Edward S. Bernard

ABSTRACTConsiderable mechanical and environmental reliability testing as defined by MIL-STD-883 has been performed on GE HDI modules in both hermetic and nonhermetic configurations. The tests involving temperature cycling, temperature bakes, thermal shock, power cycling by self-heating, vibration, centrifuge and drop shock showed no change in the overlay or in the performance of the underlaying chips on the substrate. As an additional reliability test, the effect of humidity cycling (45° - 95° relative humidity) on nonhermetic HDI substrates has been also investigated. Any noticeable failures and degradation of metallization were not observed by humidity cycling itself at room temperature. Both the 883 and humidity cycling test could lead to the conclusion that HDI is a robust MCM-D technology. In addition, extensive studies on the residual stress analysis of the thin film layers of metal and polymer during fabrication and thermal cycling have been performed using the Flexus laser beam bending instrument. The study results predicted that failure of overlay HDI such as delamination between layers is less likely because of lower in-plane stresses than in conventional spin-coated and cured polyimide.

Author(s):  
P. P. Fedirko ◽  
V. O. Krol ◽  
V. S. Bonchyk

The article presents the study results of the anaerobic materials effect on the strength of threaded connections in the repair of machinery and equipment. Their use is the simplest, most economical and reliable method of fixing and restoring threaded connections. The basis of the anaerobic compositions is polymerization compounds of the acrylic series, most often dimethacrylic and polyalkylene glycol ethers, which are characterized by a high conversion rate into spatially cross-linked polymers. Unlike mechanical methods of fixation and recovery, anaerobic materials completely fill the space between the threads of the spiral. This significantly increases the friction between the parts of the connection, improves the protection of the metal of the interface against corrosion, increases the torque when unscrewing in relation to the tightening torque, increases the resistance of the connection to the action of vibration, shock, shock loads. For the research, anaerobic thread locks were purchased, which were tested according to the same procedure and, after 24 hours at room temperature, each connection was clamped in a vice in turn so that the head of the torque wrench captures only the top nut, which had to be unscrewed. The rate of hardening of anaerobic adhesives is influenced by the size of the gaps between the combined surfaces, temperature, cleaning quality, the nature of the coating, etc. It has been established that the presence of polymerized anaerobic materials in the contact zone of parts significantly increases the strength of the joints. The conducted studies allowed to verify in practice the conformity of the tested anaerobic clamps of threaded connections to the stated parameters, to delineate the scope of their application. So, anaerobic adhesives for fixing threaded connections allow you to fix screws, nuts, bolts and pins to protect against loosening and loosening due to vibration


2013 ◽  
Vol 690-693 ◽  
pp. 1702-1706 ◽  
Author(s):  
Shuang Jun Nie ◽  
Hao Geng ◽  
Jun Bao Wang ◽  
Lai Sen Wang ◽  
Zhen Wei Wang ◽  
...  

NiZn-ferrite thin films were deposited onto silicon and glass substrates by radio frequency magnetron sputtering at room temperature. The effects of the relative oxygen flow ratio on the structure and magnetic properties of the thin films were investigated. The study results reveal that the films deposited under higher relative oxygen flow ratio show a better crystallinity. Static magnetic measurement results indicated that the saturation magnetization of the films was greatly affected by the crystallinity, grain dimension, and cation distribution in the NiZn-ferrite films. The NiZn-ferrite thin films with a maximum saturation magnetization of 151 emucm-3, which is about 40% of the bulk NiZn ferrite, was obtained under relative oxygen flow ratio of 60%.


2019 ◽  
Vol 19 (01) ◽  
pp. 1950003
Author(s):  
P. R. Ghutepatil ◽  
S. H. Pawar

In this paper, uniform and superparamagnetic nanoparticles have been prepared using one-step polyol synthesis method. Structural, morphological and magnetic properties of obtained MnFe2O4 nanoparticles have been investigated by using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), field emission scanning electron microscope (FE-SEM), transmission electron microscopy (TEM), vibrating sample magnetometry (VSM) and thermogravimetric analysis (TGA) techniques. Structural investigation showed that the average crystallite size of obtained nanoparticles was about 10[Formula: see text]nm. Magnetic study revealed that the nanoparticles were superparamagnetic at room temperature with magnetization 67[Formula: see text]emu/g at room temperature. The self-heating characteristics of synthesized MnFe2O4 nanoparticles were studied by applying external AC magnetic field of 167.6 to 335.2[Formula: see text]Oe at a fixed frequency of 265[Formula: see text]kHz. The SAR values of MnFe2O4 nanoparticles were calculated for 2, 5, 10[Formula: see text]mg[Formula: see text]mL[Formula: see text] concentrations and it is observed that the threshold hyperthermia temperature is achieved for all concentrations.


Author(s):  
Y. Yang ◽  
M. Asheghi

Giant Magnetoresistance (GMR) head technology is one of the latest advancement in hard disk drive (HDD) storage industry. The GMR head superlattice structure consists of alternating layers of extremely thin metallic ferromagnet and paramagnet films. A large decrease in the resistivity from antiparallel to parallel alignment of the film magnetizations can be observed, known as giant magnetoresistance (GMR) effect. The present work characterizes the in-plane electrical and thermal conductivities of Cu/CoFe GMR multilayer structure in the temperature range of 50 K to 340 K using Joule-heating and electrical resistance thermometry in suspended bridges. The thermal conductivity of the GMR layer monotonously increased from 25 Wm−1K−1 (at 55 K) to nearly 50 Wm−1K−1 (at room temperature). We also report the GMR ratio of 17% and a large negative magnetothermal resistance effect (GMTR) of 33% in Cu/CoFe superlattice structure. The Boltzmann transport equation (BTE) is used to estimate the GMR ratio, and to investigate the effect of repeats, as well as the spin-dependent interface and boundary scatting on the transport properties of the GMR structure. Aside from the interesting underlying physics, these data can be used in the predictions of the Electrostatic Discharge (ESD) failure and self-heating in GMR heads.


2013 ◽  
Vol 846-847 ◽  
pp. 587-591
Author(s):  
Jin Hui Wang ◽  
Jun Ai ◽  
Lin Zhi Huang

Embedded system is applied more and more extensively in the fields of national defense weapon equipment. With the increasing complexity of embedded systems, the combination of the hardware with software is more and closer. Because of the overall characteristic of hardware and software combination in embedded system, traditional reliability test can hardly accurately identify the reliability of embedded systems. The proposed combined reliability testing method, which combines software reliability test with system integrated environmental stress test to simulate the state of system running, provides the basis for the accurate validation and evaluation of reliability of embedded system.


Author(s):  
Xianjie Yang ◽  
Sayed A. Nassar ◽  
Zhijun Wu

This paper investigates the clamp load loss in threaded fittings with a collapsible metal gasket for elevated temperature application. Firstly, the joint is tested at room temperature to find the correlation between the joint clamp load, the tightening torque, and the angle of turn. Secondly, a mathematical model for clamp load loss of the bolted joints under temperature cycling is proposed for predicting the clamp load variation. Although the bolt and the joint would normally undergo linear elastic deformation at room temperature, they are more likely to exhibit nonlinear behavior at high temperature due to the reduced material strength. The plastic or creep deformation of the bolt, gasket, and joint would cause permanent clamp load loss that may lead to joint leakage, part separation, or plastic thread deformation that would significantly increase the cost of fitting replacement and/or maintenance. A non-linear finite element model is used with temperature dependent material properties. The FEA model is used to investigate the clamp load loss of the threaded fittings due to plastic and creep behavior. Some measures for enhancing the threaded fitting reliability at elevated temperature are proposed.


Blood ◽  
2011 ◽  
Vol 118 (21) ◽  
pp. 720-720
Author(s):  
Fei Xu ◽  
Monique Gelderman-Fuhrmann ◽  
John Farrell ◽  
Jaroslav Vostal

Abstract Abstract 720 Platelets are currently limited to 5 days of storage at room temperature to prevent growth of bacteria to high levels. Cold storage of platelets could reduce bacterial proliferation but platelets stored in cold for over 48 hours are cleared rapidly from circulation through the hepatocyte Ashwell-Morell (AM) receptor thus limiting the applicability of cold temperatures to platelet storage. We used a temperature cycling method to store human platelets in the cold without decreasing their in vivo recovery in an immunodeficient (SCID) animal model of transfusion. Temperature cycled (TC) apheresis human platelets were stored in the cold (4°C) for 12 hours and then incubated at 37°C for 30 minutes before returning back to cold storage. The TC (37°C pulses for 30 minutes at 12 hour intervals) was continued for 2, 5 and 7 days. Human platelets stored either at room temperature (RT), cold or TC for 2, 5 and 7 days were infused into 6 to 8 SCID mice per group and their in vivo recovery in circulation was determined at 5, 20 and 60 minutes after transfusion by flow cytometry. Carbohydrate exposure on the surface of the platelets was analyzed for galactose by Erythrina cristagalli agglutinin (ECA), and for β-GlnNAc by succinyl wheat germ agglutinin (sWGA) using flow cytometry. Involvement of the AM receptor was examined by monitoring clearance of cold stored platelets in the presence of asialofetuin, a competitive ligand for the receptor. In vivo recovery of human platelets stored for two-days in SCID mice circulation is shown in Figure 1. As expected, cold platelets had significantly decreased recovery compared to RT platelets, from 22.1±2.5% to 11.1±3.3% (P<0.01), 11.5±2.9% to 5.5±3.6% (P<0.01) and 11.2±1.4% to 6.2±1.8% (P<0.01) respectively at 5, 20 and 60 min post platelets injection. Compared to cold platelets, TC platelets recovery increased significantly from 11.1±3.3% to 15.9±4.4% (P<0.01), 5.5±3.6+% to 10.5±4.7% (P<0.01) and 6.2±1.8% to 9.5±2.2% (P<0.05) respectively at 5, 20 and 60 min post platelets injection. At 20 and 60 min post injection, the TC platelets have recovery of 10.5±4.7% and 9.5±2.2% respectively, that are comparable (P>0.05%) to RT platelet recoveries of 11.5±2.9% and 11.2±1.4% for the same time points. Similar increases of in vivo recovery for TC platelets as compared to cold platelets were obtained for at 5 and 7 days.Figure 1Human Platelet Recovery (% of total platelets circulating) * p< 0.05, ** p< 0.01, *** p< 0.001Figure 1. Human Platelet Recovery (% of total platelets circulating) * p< 0.05, ** p< 0.01, *** p< 0.001 Binding of the galactose specific lectin, ECA, was increased by 142±22% from RT to cold platelets (P<0.01) as previously reported. However, binding of ECA was also increased by 134±16% from RT to TC platelets (P<0.01). β-GlnNAc exposure, as measured by sWGA lectin binding, was increased after cold and TC storage by 222±65% (P<0.01) and 197±14% (P<0.01), respectively, when compared to RT platelets. Platelets stored in the cold for >48 hours have been reported to be cleared through the hepatic AM receptor which recognizes asialocarbohydrates. Co-injection of asialofetuin significantly improved the recovery of two-day cold stored platelets from 9.5±5.1% to 18.4±7.3% (P<0.05) and 4.8±3.7% to 12.1±4.9% (P<0.01), at 5 min and 20 min post injection, respectively. Native fetuin did not alter the clearance of cold platelets. However, there was no significant increase in the recovery of TC platelets in the presence of asialofetuin as compared to fetuin injection (P>0.28), even though the TC platelets, like cold platelets, have significantly increased β-galactose exposure. Our results indicate that ‘temperature cycling' during cold storage of platelets may be an effective method to store human platelets up to 7 days without loss of in vivo recovery after transfusion when compared to RT platelets. Temperature cycling does not alter the cold induced increases in β-gal or β-GlcNAc expression which suggests that there are other mechanisms besides binding to the AM receptor that mediate clearance of platelets stored in the cold for >48 hours. The findings and conclusions in this abstract have not been formally disseminated by the Food and Drug Administration and should not be construed to represent any Agency determination or policy. Disclosures: No relevant conflicts of interest to declare.


Sign in / Sign up

Export Citation Format

Share Document