Strain Tuned Magnetic Properties of Epitaxial Cobalt Ferrite Thin Films

1999 ◽  
Vol 603 ◽  
Author(s):  
G. Hu ◽  
J.H. Choi ◽  
C.B. Eom ◽  
Y. Suzuki
Keyword(s):  
Thin Films ◽  
Magnetic Properties ◽  
Cobalt Ferrite ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Ferrite Thin Films ◽  
Cation Redistribution ◽  
Structural Characterizations ◽  
Post Deposition

AbstractEpitaxial cobalt ferrite thin films have been fabricated on bare MgO substrates and compared to those grown on CoCr2O4 buffered MgAl2O4. Various structural characterizations, including x-ray diffraction, Rutherford backscattering spectroscopy and transmission electron microscopy, demonstrate excellent crystallinity of the films. Films grown under tension exhibit magnetic properties dominated by the stress anisotropy. In (110) oriented films grown on CoCr2O4 buffered MgAl2O4, post deposition annealing switched the in-plane easy and hard directions completely while no such behavior is observed in cobalt ferrite films grown on MgO. The anomalous behaviors observed in as-grown films and films after annealing can be explained in terms of lattice distortion and cation redistribution.

TEM Study of FePt and FePt:C/FePt Composite Double-Layered Thin Films

2013 ◽  
Vol 275-277 ◽  
pp. 1952-1955
Author(s):  
Ling Fang Jin ◽  
Xing Zhong Li
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Transmission Electron Microscopy ◽  
Grain Size ◽  
Magnetic Properties ◽  
Composite Layer ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron

New functional nanocomposite FePt:C thin films with FePt underlayers were synthesized by noneptaxial growth. The effect of the FePt layer on the ordering, orientation and magnetic properties of the composite layer has been investigated by adjusting FePt underlayer thickness from 2 nm to 14 nm. Transmission electron microscopy (TEM), together with x-ray diffraction (XRD), has been used to check the growth of the double-layered films and to study the microstructure, including the grain size, shape, orientation and distribution. XRD scans reveal that the orientation of the films was dependent on FePt underlayer thickness. In this paper, the TEM studies of both single-layered nonepitaxially grown FePt and FePt:C composite L10 phase and double-layered deposition FePt:C/FePt are presented.

Fine Tuning Magnetic Properties of FePt:C Thin Films by FePt UnderLayers

2013 ◽  
Vol 313-314 ◽  
pp. 254-257
Author(s):  
Ling Fang Jin ◽  
Hong Zhuang
Keyword(s):  
Thin Film ◽  
Electron Microscopy ◽  
Thin Films ◽  
Magnetic Properties ◽  
Fine Tuning ◽  
Nanocomposite Films ◽  
Nanocomposite Thin Film ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron

Nonepitaxially grown FePt (x)/FePt:C thin films were synthesized, where FePt (x) (x=2, 5, 8, 11, 14 nm) layers were served as underlayers and FePt:C layer was nanocomposite with thickness of 5 nm. The effect of FePt underlayer on the ordering, orientation and magnetic properties of FePt:C thin films has been investigated by adjusting FePt underlayer thicknesses from 2 nm to 14 nm. X-ray diffraction (XRD), together with transmission electron microscopy (TEM) confirmed that the desired L10 phase was formed and films were (001) textured with FePt underlayer thickness decreased less 5 nm. For 5 nm FePt:C nanocomposite thin film with 2 nm FePt underlayer, the coercivity was 8.2 KOe and the correlation length of FePt:C nanocomposite film was 67 nm. These results reveal that the better orientation and magnetic properties for FePt:C nanocomposite films can be tuned by decreasing FePt underlayer thickness.

Research on Structural Properties of FePt: C Thin Films with FePt Underlayers

2013 ◽  
Vol 385-386 ◽  
pp. 7-10
Author(s):  
Ling Fang Jin ◽  
Hong Zhuang
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Transmission Electron Microscopy ◽  
Magnetic Properties ◽  
Structural Properties ◽  
Composite Layer ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron

Nonepitaxially grown double-layered films were synthesized with a FePt: C composite layer on top of continuous FePt underlayer. The thickness of FePt was changed from 2 nm to 14 nm. Nanostructures, crystalline orientations and the effect of FePt underlayer on the ordering, orientation and magnetic properties of the thin films were investigated by transmission electron microscopy (TEM) and x-ray diffraction (XRD). XRD confirmed the formation of the ordered L10phase for 5 nm FePt: C film with FePt thickness decreased to 5 nm. TEM studies of FePt:C composite L10phase and double-layered deposition FePt:C/FePt were presented.

Structural and Magnetic Properties of CoFe2O4 / Si (001) Thin Films via Sol-Gel Method

2013 ◽  
Vol 744 ◽  
pp. 315-318
Author(s):  
Wei Rao ◽  
Ding Guo Li ◽  
Hong Chun Yan
Keyword(s):  
Thin Films ◽  
Magnetic Properties ◽  
Exchange Coupling ◽  
Cobalt Ferrite ◽  
Sol Gel ◽  
Magnetic Hysteresis ◽  
Vibrating Sample Magnetometer ◽  
X Ray Diffraction ◽  
X Ray ◽  
Calcined Temperature

Cobalt ferrite (CoFe2O4) thin films have been prepared on Si (001) substrates, with different calcined temperatures (Tcal=400°C~800°C). The films structure was studied by X-ray diffraction (XRD) and their surface was examined by scanning electron microscopy (SEM). The magnetic properties were measured with a vibrating sample magnetometer (VSM). For low calcined temperatures, the films presented a mixture of a CoFe2O4phase, with the cubic spinel structure, and cobalt and iron antiferromagnet oxides with CoO and FeO stoichiometries. As the calcined temperature increased, the CoO and FeO relative content strongly decreased, so that for Tcal=800°Cthe films were composed mainly by polycrystalline CoFe2O4. The magnetic hysteresis cycles measured in the films were horizontally shifted due to an exchange coupling field originated by the presence of the antiferromagnetic phases.

Effect of Sputtering Input Power of Co on Structure and Magnetic Properties of Fe-Co-N Thin Films

2009 ◽  
Vol 79-82 ◽  
pp. 635-638 ◽  
Author(s):  
Xin Wang ◽  
Hui Jia ◽  
Wei Tao Zheng ◽  
Wei Xu ◽  
Bei Hong Long
Keyword(s):  
Thin Films ◽  
Magnetic Properties ◽  
Photoelectron Spectroscopy ◽  
Quantum Interference ◽  
Input Power ◽  
Superconducting Quantum Interference Device ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Composition Structure

Fe-Co-N thin films with various Co content were synthesized on Si (111) substrate using facing-target magnetron sputtering by changing sputtering input power on Co target. During deposition, the input power on Fe target was kept at 160 W. The composition, structure, and magnetic properties were examined by X-ray photoelectron spectroscopy, X-ray diffraction (XRD), transmission electron microscopy (TEM), and superconducting quantum interference device. XRD and TEM investigations showed that at lower input power of 11.2 W on Co target, the phases in the film were -(Fe,Co)4N and Co3N. Increasing sputtering input power, the content of Co in the film increased. At input power of 14 W, film contained -(Fe,Co)8N phase was produced which exhibited higher saturation magnetization (252.85 Am2/kg) and lower value of coercivity (3.66 kAm-1), corresponded to the 12% content of Co in the film.

Structural and Magnetic Properties of Nanogranular BaTiO3-CoFe2O4 Thin Films Deposited by Laser Ablation on Si/Pt Substrates

2008 ◽  
Vol 587-588 ◽  
pp. 303-307
Author(s):  
J.G. Barbosa ◽  
Bernardo G. Almeida ◽  
João P. Araújo ◽  
João Bessa Sousa ◽  
Jorge A. Mendes
Keyword(s):  
Thin Films ◽  
Grain Size ◽  
Magnetic Properties ◽  
Laser Ablation ◽  
Barium Titanate ◽  
Cobalt Ferrite ◽  
Magnetic Measurements ◽  
X Ray Diffraction ◽  
Clear Trend ◽  
X Ray

Thin film nanocomposites of cobalt ferrite (CoFe2O4) dispersed in barium titanate (BaTiO3) matrix, have been deposited with different cobalt ferrite concentrations (from 20% to 70% CoFe2O4), as well as pure barium titanate and cobalt ferrite thin films (end members). The films were prepared by pulsed laser ablation on platinum covered Si(001) substrates. The films structure was studied by X-ray diffraction and their surface was examined by scanning electron microscopy (SEM). The magnetic properties were measured in a SQUID magnetometer. The results show that the deposited films are polycrystalline with a slight (111) barium titanate phase orientation and (311) CoFe2O4 phase orientation. The grain sizes measured from the X-ray diffraction peak widths, for both phases, are in the range 40nm to 100nm. However, as the concentration of the cobalt ferrite increases, the grain size of the BaTiO3 phase decreases, from 100nm to 30nm, up to 40% CoFe2O4 concentration beyond which the BaTiO3 grain size has an approximately constant value near 30nm. On the other hand the cobalt ferrite grain size does not show a clear trend with increasing cobalt ferrite concentration, fluctuating in the range 20nm to 30nm. The magnetic measurements show an increase of the magnetic moment from the low concentration region where the magnetic grains are more isolated and their magnetic interaction is small, towards the bulk value at higher CoFe2O4 concentrations. Also, a strong reduction of the magnetization with increasing temperature was observed, due to the corresponding decrease of the magnetocristalline anisotropy of the cobalt ferrite.

Structural and Magnetic Properties of CoFe2O4 Thin Films via Sol-Gel Method

2014 ◽  
Vol 716-717 ◽  
pp. 159-162 ◽  
Author(s):  
Shao Hua Yang ◽  
Ding Guo Li ◽  
Hai Bin Yang ◽  
Hong Chun Yan
Keyword(s):  
Thin Films ◽  
Magnetic Properties ◽  
Exchange Coupling ◽  
Cobalt Ferrite ◽  
Sol Gel ◽  
Magnetic Hysteresis ◽  
Vibrating Sample Magnetometer ◽  
X Ray Diffraction ◽  
X Ray ◽  
Calcined Temperature

Cobalt ferrite (CoFe2O4) thin films have been prepared on Si (001) substrates, with different calcined temperatures (Tcal=400°C~800°C). The films structure was studied by X-ray diffraction (XRD) and their surface was examined by scanning electron microscopy (SEM). The magnetic properties were measured with a vibrating sample magnetometer (VSM). For low calcined temperatures, the films presented a mixture of a CoFe2O4phase, with the cubic spinel structure, and cobalt and iron antiferromagnet oxides with CoO and FeO stoichiometries. As the calcined temperature increased, the CoO and FeO relative content strongly decreased, so that for Tcal=800°Cthe films were composed mainly by polycrystalline CoFe2O4. The magnetic hysteresis cycles measured in the films were horizontally shifted due to an exchange coupling field originated by the presence of the antiferromagnetic phases.

Palladium Nanowire Thin Films via Template Growth

2003 ◽  
Vol 775 ◽  
Author(s):  
Donghai Wang ◽  
David T. Johnson ◽  
Byron F. McCaughey ◽  
J. Eric Hampsey ◽  
Jibao He ◽  
...  
Keyword(s):  
Thin Film ◽  
Electron Microscopy ◽  
Thin Films ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Conductive Substrate ◽  
Palladium Nanowires ◽  
Efficient Route ◽  
Silica Thin Film

AbstractPalladium nanowires have been electrodeposited into mesoporous silica thin film templates. Palladium continually grows and fills silica mesopores starting from a bottom conductive substrate, providing a ready and efficient route to fabricate a macroscopic palladium nanowire thin films for potentially use in fuel cells, electrodes, sensors, and other applications. X-ray diffraction (XRD) and transmission electron microscopy (TEM) indicate it is possible to create different nanowire morphology such as bundles and swirling mesostructure based on the template pore structure.

Effect of Nitridation Magnetic Properties of Nanocrystalline Fe-Co Alloy Powders

2010 ◽  
Vol 654-656 ◽  
pp. 1106-1109
Author(s):  
Ya Qiong He ◽  
Chang Hui Mao ◽  
Jian Yang
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
Alloy Powder ◽  
High Energy ◽  
X Ray Diffraction ◽  
Powder Mixtures ◽  
X Ray ◽  
Transmission Electron ◽  
Nitridation Temperature ◽  
Microstructure And Magnetic Properties

Nanocrystalline Fe-Co alloy powders, which were prepared by high-energy mechanical milling, were nitrided under the mixing gas of NH3/H2 in the temperature range from 380°C to 510°C. X-ray diffraction (XRD) was used to analyze the grain size and reaction during the processing. The magnetic properties of the nitrided powders were measured by Vibrating Sample Magnetometer (VSM). The results show that with the appearance of Fe4N phase after nitride treatment, and the grain-size of FeCo phase decreases with the increase of nitridation temperature between 380°C to 450°C.The saturation magnetization of nitrided alloy powder treated at 480°C is about 18% higher than that of the initial Fe-Co alloy powder, accompanied by the reduction of the coercivity. Transmission electron microscope (TEM) was used, attempting to further analyze the effect of Fe4N phase on microstructure and magnetic properties of the powder mixtures.

Influence of Alloying Additions on Enhancement of Soft Magnetic Properties Effect and Crystallization in FeXSiB (X=Cu, V, Co, Zr, Nb) Amorphous Alloys

2007 ◽  
Vol 130 ◽  
pp. 171-174 ◽  
Author(s):  
Z. Stokłosa ◽  
G. Badura ◽  
P. Kwapuliński ◽  
Józef Rasek ◽  
G. Haneczok ◽  
...  
Keyword(s):  
Magnetic Properties ◽  
Amorphous Alloys ◽  
Crystallization Process ◽  
Annealing Temperature ◽  
Magnetic Measurements ◽  
X Ray Diffraction ◽  
Soft Magnetic ◽  
X Ray ◽  
Second Stage ◽  
Transmission Electron

The crystallization and optimization of magnetic properties effects in FeXSiB (X=Cu, V, Co, Zr, Nb) amorphous alloys were studied by applying X-ray diffraction methods, high resolution transmission electron microscopy (HRTEM), resistometric and magnetic measurements. The temperatures of the first and the second stage of crystallization, the 1h optimization annealing temperature and the Curie temperature were determined for different amorphous alloys. Activation energies of crystallization process were obtained by applying the Kissinger method. The influence of alloy additions on optimization effect and crystallization processes was carefully examined.

Sign in / Sign up

Export Citation Format

Share Document