Structural and Magnetic Properties of Nanogranular BaTiO3-CoFe2O4 Thin Films Deposited by Laser Ablation on Si/Pt Substrates

2008 ◽  
Vol 587-588 ◽  
pp. 303-307
Author(s):  
J.G. Barbosa ◽  
Bernardo G. Almeida ◽  
João P. Araújo ◽  
João Bessa Sousa ◽  
Jorge A. Mendes
Keyword(s):  
Thin Films ◽  
Grain Size ◽  
Magnetic Properties ◽  
Laser Ablation ◽  
Barium Titanate ◽  
Cobalt Ferrite ◽  
Magnetic Measurements ◽  
X Ray Diffraction ◽  
Clear Trend ◽  
X Ray

Thin film nanocomposites of cobalt ferrite (CoFe2O4) dispersed in barium titanate (BaTiO3) matrix, have been deposited with different cobalt ferrite concentrations (from 20% to 70% CoFe2O4), as well as pure barium titanate and cobalt ferrite thin films (end members). The films were prepared by pulsed laser ablation on platinum covered Si(001) substrates. The films structure was studied by X-ray diffraction and their surface was examined by scanning electron microscopy (SEM). The magnetic properties were measured in a SQUID magnetometer. The results show that the deposited films are polycrystalline with a slight (111) barium titanate phase orientation and (311) CoFe2O4 phase orientation. The grain sizes measured from the X-ray diffraction peak widths, for both phases, are in the range 40nm to 100nm. However, as the concentration of the cobalt ferrite increases, the grain size of the BaTiO3 phase decreases, from 100nm to 30nm, up to 40% CoFe2O4 concentration beyond which the BaTiO3 grain size has an approximately constant value near 30nm. On the other hand the cobalt ferrite grain size does not show a clear trend with increasing cobalt ferrite concentration, fluctuating in the range 20nm to 30nm. The magnetic measurements show an increase of the magnetic moment from the low concentration region where the magnetic grains are more isolated and their magnetic interaction is small, towards the bulk value at higher CoFe2O4 concentrations. Also, a strong reduction of the magnetization with increasing temperature was observed, due to the corresponding decrease of the magnetocristalline anisotropy of the cobalt ferrite.

Structural and Magnetic Properties of Nanogranular BaTiO3-CoFe2O4 Thin Films Deposited by Laser Ablation on Si/Pt Substrates

2006 ◽  
Vol 966 ◽  
Author(s):  
José Barbosa ◽  
Bernardo Almeida ◽  
Jorge A. Mendes ◽  
Anabela G. Rolo ◽  
João P. Araújo ◽  
...  
Keyword(s):  
Grain Size ◽  
Laser Ablation ◽  
Barium Titanate ◽  
Cobalt Ferrite ◽  
Magnetic Measurements ◽  
Lattice Parameter ◽  
Particle Agglomeration ◽  
Clear Trend ◽  
Tetragonal Batio ◽  
Ferrite Grain Size

ABSTRACTThin film nanogranular composites of cobalt ferrite (CoFe2O4) dispersed in a barium titanate (BaTiO3) matrix were deposited by laser ablation with different cobalt ferrite concentrations (x). The films were polycrystalline and composed by a mixture of tetragonal-BaTiO3 and CoFe2O4 with the cubic spinnel structure. A slight (111) barium titanate phase orientation and (311) CoFe2O4 phase orientation was observed. As the concentration of the cobalt ferrite increased, the grain size of the BaTiO3 phase decreased, from 91nm to 30nm, up to 50% CoFe2O4 concentration, beyond which the BaTiO3 grain size take values in the range 30-35nm. On the other hand the cobalt ferrite grain size did not show a clear trend with increasing cobalt ferrite concentration, fluctuating in the range 25nm to 30nm. The lattice parameter of the CoFe2O4 phase increased with increasing x. However, it was always smaller than the bulk value indicating that, in the films, the cobalt ferrite was under compressive stress that was progressively relaxed with increasing CoFe2O4 concentration. The magnetic measurements showed a decrease of coercive field with increasing x, which was attributed to the relaxation of the stress in the films and to the increase of particle agglomeration in bigger polycrystalline clusters with increasing cobalt ferrite concentration.

TEM Study of FePt and FePt:C/FePt Composite Double-Layered Thin Films

2013 ◽  
Vol 275-277 ◽  
pp. 1952-1955
Author(s):  
Ling Fang Jin ◽  
Xing Zhong Li
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Transmission Electron Microscopy ◽  
Grain Size ◽  
Magnetic Properties ◽  
Composite Layer ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron

New functional nanocomposite FePt:C thin films with FePt underlayers were synthesized by noneptaxial growth. The effect of the FePt layer on the ordering, orientation and magnetic properties of the composite layer has been investigated by adjusting FePt underlayer thickness from 2 nm to 14 nm. Transmission electron microscopy (TEM), together with x-ray diffraction (XRD), has been used to check the growth of the double-layered films and to study the microstructure, including the grain size, shape, orientation and distribution. XRD scans reveal that the orientation of the films was dependent on FePt underlayer thickness. In this paper, the TEM studies of both single-layered nonepitaxially grown FePt and FePt:C composite L10 phase and double-layered deposition FePt:C/FePt are presented.

scholarly journals Structural and Magnetic Properties of FePd Thin Film Synthesized by Electrodeposition Method

Materials ◽  
2020 ◽  
Vol 13 (6) ◽  
pp. 1454
Author(s):  
Gabriele Barrera ◽  
Federico Scaglione ◽  
Matteo Cialone ◽  
Federica Celegato ◽  
Marco Coïsson ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Magnetic Properties ◽  
Deposition Time ◽  
Magnetic Measurements ◽  
X Ray Diffraction ◽  
X Ray ◽  
Fundamental Properties ◽  
Magnetic Features ◽  
Application Fields

Bimetallic nanomaterials in the form of thin film constituted by magnetic and noble elements show promising properties in different application fields such as catalysts and magnetic driven applications. In order to tailor the chemical and physical properties of these alloys to meet the applications requirements, it is of great importance scientific interest to study the interplay between properties and morphology, surface properties, microstructure, spatial confinement and magnetic features. In this manuscript, FePd thin films are prepared by electrodeposition which is a versatile and widely used technique. Compositional, morphological, surface and magnetic properties are described as a function of deposition time (i.e., film thickness). Chemical etching in hydrochloric acid was used to enhance the surface roughness and help decoupling crystalline grains with direct consequences on to the magnetic properties. X-ray diffraction, SEM/AFM images, contact angle and magnetic measurements have been carried out with the aim of providing a comprehensive characterisation of the fundamental properties of these bimetallic thin films.

Structural, Mechanical and Magnetic Properties of Mechanically Alloyed Fe40Co60 Powders

2011 ◽  
Vol 312-315 ◽  
pp. 743-747 ◽  
Author(s):  
Fadhela Otmane ◽  
S. Bergheul ◽  
M. Zergoug ◽  
M. Azzaz
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
Magnetic Measurements ◽  
Lattice Parameter ◽  
Internal Strain ◽  
Morphological Aspect ◽  
Micro Hardness ◽  
X Ray Diffraction ◽  
Mechanically Alloyed ◽  
X Ray

In this work we report on the structural, mechanical and magnetic properties of mechanically alloyed Fe40Co60 powders. Alloying formation, grain size, lattice parameter and internal strain were investigated using X-Ray Diffraction (XRD) measurements. The morphological aspect of the nanostructured powders was analysed by means of the Scanning Electron Microscopy (SEM). Compacted pastilles with circular shape have been under Vickers test of micro Hardness and magnetic measurements of Hysterisis loops. Discussed results according to milling time show that after 60 h milling the grain refinement is about 15.59 nm with internal strain of around 0.5809 %. The micro hardness increases with the decrease of the grain size and the hysterisis loop at 60 h milling is enhanced in term of decreased coercivity.

Structural and Magnetic Properties of CoFe2O4 / Si (001) Thin Films via Sol-Gel Method

2013 ◽  
Vol 744 ◽  
pp. 315-318
Author(s):  
Wei Rao ◽  
Ding Guo Li ◽  
Hong Chun Yan
Keyword(s):  
Thin Films ◽  
Magnetic Properties ◽  
Exchange Coupling ◽  
Cobalt Ferrite ◽  
Sol Gel ◽  
Magnetic Hysteresis ◽  
Vibrating Sample Magnetometer ◽  
X Ray Diffraction ◽  
X Ray ◽  
Calcined Temperature

Cobalt ferrite (CoFe2O4) thin films have been prepared on Si (001) substrates, with different calcined temperatures (Tcal=400°C~800°C). The films structure was studied by X-ray diffraction (XRD) and their surface was examined by scanning electron microscopy (SEM). The magnetic properties were measured with a vibrating sample magnetometer (VSM). For low calcined temperatures, the films presented a mixture of a CoFe2O4phase, with the cubic spinel structure, and cobalt and iron antiferromagnet oxides with CoO and FeO stoichiometries. As the calcined temperature increased, the CoO and FeO relative content strongly decreased, so that for Tcal=800°Cthe films were composed mainly by polycrystalline CoFe2O4. The magnetic hysteresis cycles measured in the films were horizontally shifted due to an exchange coupling field originated by the presence of the antiferromagnetic phases.

Strain Tuned Magnetic Properties of Epitaxial Cobalt Ferrite Thin Films

1999 ◽  
Vol 603 ◽  
Author(s):  
G. Hu ◽  
J.H. Choi ◽  
C.B. Eom ◽  
Y. Suzuki
Keyword(s):  
Thin Films ◽  
Magnetic Properties ◽  
Cobalt Ferrite ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Ferrite Thin Films ◽  
Cation Redistribution ◽  
Structural Characterizations ◽  
Post Deposition

AbstractEpitaxial cobalt ferrite thin films have been fabricated on bare MgO substrates and compared to those grown on CoCr2O4 buffered MgAl2O4. Various structural characterizations, including x-ray diffraction, Rutherford backscattering spectroscopy and transmission electron microscopy, demonstrate excellent crystallinity of the films. Films grown under tension exhibit magnetic properties dominated by the stress anisotropy. In (110) oriented films grown on CoCr2O4 buffered MgAl2O4, post deposition annealing switched the in-plane easy and hard directions completely while no such behavior is observed in cobalt ferrite films grown on MgO. The anomalous behaviors observed in as-grown films and films after annealing can be explained in terms of lattice distortion and cation redistribution.

Structural and Magnetic Properties of CoFe2O4 Thin Films via Sol-Gel Method

2014 ◽  
Vol 716-717 ◽  
pp. 159-162 ◽  
Author(s):  
Shao Hua Yang ◽  
Ding Guo Li ◽  
Hai Bin Yang ◽  
Hong Chun Yan
Keyword(s):  
Thin Films ◽  
Magnetic Properties ◽  
Exchange Coupling ◽  
Cobalt Ferrite ◽  
Sol Gel ◽  
Magnetic Hysteresis ◽  
Vibrating Sample Magnetometer ◽  
X Ray Diffraction ◽  
X Ray ◽  
Calcined Temperature

Cobalt ferrite (CoFe2O4) thin films have been prepared on Si (001) substrates, with different calcined temperatures (Tcal=400°C~800°C). The films structure was studied by X-ray diffraction (XRD) and their surface was examined by scanning electron microscopy (SEM). The magnetic properties were measured with a vibrating sample magnetometer (VSM). For low calcined temperatures, the films presented a mixture of a CoFe2O4phase, with the cubic spinel structure, and cobalt and iron antiferromagnet oxides with CoO and FeO stoichiometries. As the calcined temperature increased, the CoO and FeO relative content strongly decreased, so that for Tcal=800°Cthe films were composed mainly by polycrystalline CoFe2O4. The magnetic hysteresis cycles measured in the films were horizontally shifted due to an exchange coupling field originated by the presence of the antiferromagnetic phases.

Nanocrystalline Solutions as Precursors to The Spray Deposition of Cdte Thin Films

1995 ◽  
Vol 382 ◽  
Author(s):  
Martin Pehnt ◽  
Douglas L. Schulz ◽  
Calvin J. Curtis ◽  
Helio R. Moutinho ◽  
Amy Swartzlander ◽  
...  
Keyword(s):  
Thin Films ◽  
Atomic Force Microscopy ◽  
Grain Size ◽  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Cdte Nanoparticles ◽  
Atomic Force ◽  
Vis Spectroscopy ◽  
Cdte Thin Films

ABSTRACTIn this article we report the first nanoparticle-derived route to smooth, dense, phase-pure CdTe thin films. Capped CdTe nanoparticles were prepared by injection of a mixture of Cd(CH3)2, (n-C8H17)3 PTe and (n-C8H17)3P into (n-C8H17)3PO at elevated temperatures. The resultant nanoparticles 32-45 Å in diameter were characterized by x-ray diffraction, UV-Vis spectroscopy, transmission electron microscopy, thermogravimetric analysis and energy dispersive x-ray spectroscopy. CdTe thin film deposition was accomplished by dissolving CdTe nanoparticles in butanol and then spraying the solution onto SnO2-coated glass substrates at variable susceptor temperatures. Smooth and dense CdTe thin films were obtained using growth temperatures approximately 200 °C less than conventional spray pyrolysis approaches. CdTe films were characterized by x-ray diffraction, UV-Vis spectroscopy, atomic force microscopy, and Auger electron spectroscopy. An increase in crystallinity and average grain size as determined by x-ray diffraction was noted as growth temperature was increased from 240 to 300 °C. This temperature dependence of film grain size was further confirmed by atomic force microscopy with no remnant nanocrystalline morphological features detected. UV-Vis characterization of the CdTe thin films revealed a gradual decrease of the band gap (i.e., elimination of nanocrystalline CdTe phase) as the growth temperature was increased with bulk CdTe optical properties observed for films grown at 300 °C.

Effect of Nitridation Magnetic Properties of Nanocrystalline Fe-Co Alloy Powders

2010 ◽  
Vol 654-656 ◽  
pp. 1106-1109
Author(s):  
Ya Qiong He ◽  
Chang Hui Mao ◽  
Jian Yang
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
Alloy Powder ◽  
High Energy ◽  
X Ray Diffraction ◽  
Powder Mixtures ◽  
X Ray ◽  
Transmission Electron ◽  
Nitridation Temperature ◽  
Microstructure And Magnetic Properties

Nanocrystalline Fe-Co alloy powders, which were prepared by high-energy mechanical milling, were nitrided under the mixing gas of NH3/H2 in the temperature range from 380°C to 510°C. X-ray diffraction (XRD) was used to analyze the grain size and reaction during the processing. The magnetic properties of the nitrided powders were measured by Vibrating Sample Magnetometer (VSM). The results show that with the appearance of Fe4N phase after nitride treatment, and the grain-size of FeCo phase decreases with the increase of nitridation temperature between 380°C to 450°C.The saturation magnetization of nitrided alloy powder treated at 480°C is about 18% higher than that of the initial Fe-Co alloy powder, accompanied by the reduction of the coercivity. Transmission electron microscope (TEM) was used, attempting to further analyze the effect of Fe4N phase on microstructure and magnetic properties of the powder mixtures.

Influence of Alloying Additions on Enhancement of Soft Magnetic Properties Effect and Crystallization in FeXSiB (X=Cu, V, Co, Zr, Nb) Amorphous Alloys

2007 ◽  
Vol 130 ◽  
pp. 171-174 ◽  
Author(s):  
Z. Stokłosa ◽  
G. Badura ◽  
P. Kwapuliński ◽  
Józef Rasek ◽  
G. Haneczok ◽  
...  
Keyword(s):  
Magnetic Properties ◽  
Amorphous Alloys ◽  
Crystallization Process ◽  
Annealing Temperature ◽  
Magnetic Measurements ◽  
X Ray Diffraction ◽  
Soft Magnetic ◽  
X Ray ◽  
Second Stage ◽  
Transmission Electron

The crystallization and optimization of magnetic properties effects in FeXSiB (X=Cu, V, Co, Zr, Nb) amorphous alloys were studied by applying X-ray diffraction methods, high resolution transmission electron microscopy (HRTEM), resistometric and magnetic measurements. The temperatures of the first and the second stage of crystallization, the 1h optimization annealing temperature and the Curie temperature were determined for different amorphous alloys. Activation energies of crystallization process were obtained by applying the Kissinger method. The influence of alloy additions on optimization effect and crystallization processes was carefully examined.

Sign in / Sign up

Export Citation Format

Share Document