Enzymes and Cells Confined in Silica Nanopores

2000 ◽  
Vol 651 ◽  
Author(s):  
Jacques Livage ◽  
Cécile Roux ◽  
Thibaud Coradin ◽  
Souad Fennouh ◽  
Stéphanie Guyon ◽  
...  

AbstractThe sol-gel process opens new possibilities in the field of biotechnologies. Sol-gel glasses are formed at room temperature via the polymerization of molecular precursors. Enzymes can be added to the solution of precursors and trapped within the growing silica network. Small substrate molecules can diffuse through the pores allowing reactions to be performed in-situ, within the silica gels. Enzyme are encased by the hydrated silica in a cage tailored to their size, they retain their biocatalytic activity and may even be stabilized within the sol-gel matrix.Whole cell bacteria have also been immobilized within sol-gel glasses. They behave as a "bag of enzymes" and their membrane protects enzymes against denaturation and leaching. The cellular organization of bacteria cells is preserved upon encapsulation. Experiments performed with Escherichia coli induced to β-galactosidase show that they still exhibit noticeable enzymatic activity. Some degradation of the cell walls may even occur increasing the “measured” activity. However silica gels made from aqueous precursors seem to prevent bacteria from natural degradation upon ageing.Antibody-antigen recognition has been shown to be feasible within sol-gel matrices. Trapped antibodies bind specifically the corresponding haptens and can be used for the detection of traces of chemicals. Even whole cell protozoa have been encapsulated without any alteration of their cellular organization. For medical applications, trapped parasitic protozoa have been used as antigens for blood tests with human sera. Antigen-antibody interactions were followed by the so-called Enzyme Linked ImmunoSorbent Assays (ELISA).

2019 ◽  
Author(s):  
Roberto Köferstein

We employed indirect rapid prototyping templating to fabricate bioactive and macroporous scaffolds for bone regeneration. This templating technique utilizes lost molds made of polycaprolactone by fused deposition modeling, in which the organic/ inorganic hybrid silica sol was filled and cured. Finally, the molds were dissolved and extracted, and the remaining macroporous hybrid glass constructs were recovered. The hybrid glass scaffolds offered a fully interconnected pore structure with 63–72% porosity measured by N2-pycnometry and Hg-intrusion. In bioactive sol–gel glasses one issue is the insufficient and inhomogeneous incorporation of calcium (II) ions. To address this problem we varied the curing conditions and tested the effect of the organic crosslinker on calcium retention. We strengthened the silica network by covalent crosslinking with trimethylolpropane ethoxylate which was functionalized with 3-(triethoxysilyl)propyl isocyanate. Those scaffolds showed compressive yield strengths of up to 12.7 MPa and compressive moduli between 18 and 288 MPa. Energy dispersive X-ray spectroscopy showed that a crosslinker content of 60% in the hybrids resulted in a homogeneous calcium distribution in the glass, in contrast to 40% where we found a layer of CaCl2 on the scaffold surface. The materials exhibited bioactivity in simulated body fluid which was monitored by scanning electron microscopy and X-ray powder diffraction.


2010 ◽  
Vol 2010 ◽  
pp. 1-11 ◽  
Author(s):  
Jyoti L. Gurav ◽  
In-Keun Jung ◽  
Hyung-Ho Park ◽  
Eul Son Kang ◽  
Digambar Y. Nadargi

Silica aerogels have drawn a lot of interest both in science and technology because of their low bulk density (up to 95% of their volume is air), hydrophobicity, low thermal conductivity, high surface area, and optical transparency. Aerogels are synthesized from molecular precursors by sol-gel processing. Special drying techniques must be applied to replace the pore liquid with air while maintaining the solid network. Supercritical drying is most common; however, recently developed methods allow removal of the liquid at atmospheric pressure after chemical modification of the inner surface of the gels, leaving only a porous silica network filled with air. Therefore, by considering the surprising properties of aerogels, the present review addresses synthesis of silica aerogels by the sol-gel method, as well as drying techniques and applications in current industrial development and scientific research.


2016 ◽  
Vol 689 ◽  
pp. 126-132
Author(s):  
Opeyemi Adetola ◽  
Leonid Golovko ◽  
Aleksey Vasiliev

Silica gels containing incorporated heteropolyacids (HPAs) were synthesized in acidic media by co-condensation of tetraethoxysilane (TEOS) with phosphotungstic or phosphomolybdic acids using the sol-gel technique. The effect of the synthesis conditions on their structure and morphology was studied. Yields of modified materials were somewhat lower compared to non-modified silica gels. All materials were mesoporous but contained micropores in their structures. Presence of bands of Keggin’s structures in FT-IR spectra along with absence of XRD patterns of crystalline HPAs confirmed their fine incorporation into silica network. Particle sizes of modified materials were 500-1100 nm except for the W-containing sample obtained with trimethylstearylammonium chloride, which was significantly lower. This unusual effect was attributed to stabilization of primary silica nanoparticles by interactions between the surfactant and HPA. High ratio HPA/TEOS resulted in partial loss of porosity. Obtained results might be used for optimization of synthesis of effective catalysts and adsorbents containing HPAs in mesoporous structure.


Author(s):  
George C. Ruben ◽  
Merrill W. Shafer

Traditionally ceramics have been shaped from powders and densified at temperatures close to their liquid point. New processing methods using various types of sols, gels, and organometallic precursors at low temperature which enable densificatlon at elevated temperatures well below their liquidus, hold the promise of producing ceramics and glasses of controlled and reproducible properties that are highly reliable for electronic, structural, space or medical applications. Ultrastructure processing of silicon alkoxides in acid medium and mixtures of Ludox HS-40 (120Å spheres from DuPont) and Kasil (38% K2O &62% SiO2) in basic medium have been aimed at producing materials with a range of well defined pore sizes (∼20-400Å) to study physical phenomena and materials behavior in well characterized confined geometries. We have studied Pt/C surface replicas of some of these porous sol-gels prepared at temperatures below their glass transition point.


2000 ◽  
Vol 628 ◽  
Author(s):  
Mark A. Clarner ◽  
Michael J. Lochhead

ABSTRACTOrganically modified silica gels and dye-doped silica gels have been patterned into micrometer-scale structures on a substrate using micro molding in capillaries (MIMIC). This approach is from a class of elastomeric stamping and molding techniques collectively known as soft lithography. Soft lithography and sol-gel processing share attractive features in that they are relatively benign processes performed at ambient conditions, which makes both techniques compatible with a wide variety of organic molecules, molecular assemblies, and biomolecules. The combination of sol-gel and soft lithography, therefore, holds enormous promise as a tool for microfabrication of materials with optical, chemical, or biological functionality that are not readily patterned with conventional methods. This paper describes our investigation of micro-patterned organic-inorganic hybrid materials containing indicator dyes for microfluidic sensor applications. Reversible colorimetric pH sensing via entrapped reagents is demonstrated in a prototype microfluidic sensor element. Patterned structures range from one to tens of micrometers in cross-section and are up to centimeters in length. Fundamental chemical processing issues associated with mold filling, cracking and sensor stability are discussed.


2004 ◽  
Vol 398 (1-3) ◽  
pp. 151-156 ◽  
Author(s):  
M. Feuillade ◽  
C. Croutxé-Barghorn ◽  
L. Mager ◽  
C. Carré ◽  
A. Fort

1998 ◽  
Vol 519 ◽  
Author(s):  
L. Bergogne ◽  
S. Fennouh ◽  
J. Livage ◽  
C. Roux

AbstractBioencapsulation in sol-gel materials has been widely studied during the past decade. Trapped species appear to retain their bioactivity in the porous silica matrix. Small analytes can diffuse through the pores allowing bioreactions to be performed in-situ, inside the sol-gel glass. A wide range of biomolecules and micro-organisms have been encapsulated. The catalytic activity of enzymes is used for the realization of biosensors or bioreactors. Antibody-antigen recognition has been shown to be feasible within sol-gel matrices. Trapped antibodies bind specifically the corresponding haptens and can be used for the detection of traces of chemicals. Even whole cells are now encapsulated without any alteration of their cellular organization. They can be used for the production of chemicals or as antigens for immunoassays.


2004 ◽  
Vol 30 (3) ◽  
pp. 205-214 ◽  
Author(s):  
Massimo Bottini ◽  
Almerinda Di Venere ◽  
Lutz Tautz ◽  
Alessandro Desideri ◽  
Paolo Lugli ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document