Preparation and Characterization of Cu-Ga-Se Films of Ordered Vacancy Compound

2003 ◽  
Vol 763 ◽  
Author(s):  
S. Nishiwaki ◽  
S. Siebentritt ◽  
M. Ch. Lux-Steiner
Keyword(s):  
Short Circuit ◽  
Short Circuit Current ◽  
Bottom Layer ◽  
Soda Lime ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Chalcopyrite Structure ◽  
Soda Lime Glass ◽  
Soda Lime Glass Substrate ◽  
Glass Substrates

AbstractCu-Ga-Se films with an orderd vacancy compound (OVC) structure were prepared at substrate temperature about 500 °C by thermal co-deposition. With a preparation under extremely Se excess condition, films of the OVC were synthesized within the compositional ratio of 0.73 ≤ [Ga]/([Cu]+[Ga]) ≤ 0.86 along Cu2Se-Ga2Se3 pseudo binary system. The growth on soda-lime glass substrates improves the crystallinity compared to that on alkali-free glass. An increase in the optical bandgaps of OVC films from 1.85 eV to 1.94 eV was observed with an increase in the Ga content of the films. The deposition of Cu and Se onto Ga2Se3 films resulted in a vertically inhomogeneous film: the bottom layer with the OVC structure and the top layer with the chalcopyrite structure. A solar cell using the CuGa5.0Se8.1 film within a ZnO/CdS/CuGa-Se/Mo/soda-lime glass substrate structure showed an open circuit voltage of 947 mV, an efficiency of 2.2 %, a short circuit current density of 4.5 mA/cm2, and a fill factor of 0.52 (Air Mass 1.5, 0.5 cm2, total area).

Chemically and Electrochemically Deposited Thin Films of Tin Sulfide for Photovoltaic Structures

2009 ◽  
Vol 1165 ◽  
Author(s):  
Nini Rose Mathews
Keyword(s):  
Thin Films ◽  
Short Circuit ◽  
Chemical Deposition ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Tin Sulfide ◽  
Orthorhombic Crystal ◽  
Orthorhombic Crystal Structure ◽  
Glass Substrates

AbstractThin films of tin sulfide (SnS) were deposited on TCO-coated glass substrates by pulse electrodeposition. Cyclic voltammetry showed that SnS deposition occurs in the -0.8 V to −1 V range. The films deposited using the potential pulses of -0.95V (Von) and +0.1V (Voff) are of orthorhombic crystal structure with lattice parameters and grain size similar to those of the thin films of orthorhombic structure obtained by chemical deposition. The optical band gap of the films was 1.3 eV. In CdS/SnS heterojunctions an open circuit voltage110 mV, short circuit current density 0.72 mA/cm2 and fill factor of 0.32 are reported here.

Sb2S3/SnSe thin film solar cells by thermal evaporation

2014 ◽  
Vol 1670 ◽  
Author(s):  
José Escorcia-García ◽  
Enue Barrios-Salgado ◽  
M.T.S. Nair ◽  
P.K. Nair
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Solar Cell ◽  
Thermal Evaporation ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Glass Substrates ◽  
Cell Structures

ABSTRACTWe report a stable CdS/Sb2S3/SnSe heterojunction thin film solar cell deposited on SnO2:F (FTO) – coated glass substrates. Thermal evaporation at 10-5 Torr with substrate temperature of 400 °C was used to deposit Sb2S3 and SnSe thin films of 450 nm and 160 nm, respectively. Thin film Sb2S3 has an optical band gap (Eg) of 1.48 eV and photoconductivity (σp) of 4x10-7 Ω-1 cm-1 and thin film SnSe has an Eg of 1.28 eV and σp of 2 Ω-1 cm-1. The chemically deposited CdS thin film heated at 400 °C shows an Eg of 2.34 eV and σp of 0.1 Ω-1 cm-1. Stabilized solar cell structures with these thin films, FTO/CdS/Sb2S3/SnSe/C-Ag, showed open circuit voltage (Voc) of 0.60 V, short circuit current density (Jsc) of 5.51 mA/cm2 and power conversion efficiency (η) of 0.96% with a fill factor FF of 0.29. In the absence of the SnSe layer, Jsc decreases to 4.77 mA/cm2.

scholarly journals CdTe-Based Thin Film Solar Cells: Past, Present and Future

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1684
Author(s):  
Alessandro Romeo ◽  
Elisa Artegiani
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
Solar Cell ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Early Years ◽  
Solar Cell Efficiency ◽  
Cell Efficiency

CdTe is a very robust and chemically stable material and for this reason its related solar cell thin film photovoltaic technology is now the only thin film technology in the first 10 top producers in the world. CdTe has an optimum band gap for the Schockley-Queisser limit and could deliver very high efficiencies as single junction device of more than 32%, with an open circuit voltage of 1 V and a short circuit current density exceeding 30 mA/cm2. CdTe solar cells were introduced at the beginning of the 70s and they have been studied and implemented particularly in the last 30 years. The strong improvement in efficiency in the last 5 years was obtained by a new redesign of the CdTe solar cell device reaching a single solar cell efficiency of 22.1% and a module efficiency of 19%. In this paper we describe the fabrication process following the history of the solar cell as it was developed in the early years up to the latest development and changes. Moreover the paper also presents future possible alternative absorbers and discusses the only apparently controversial environmental impacts of this fantastic technology.

scholarly journals Ultrathin Cu(In,Ga)Se2 Solar Cells with Ag/AlOx Passivating Back Reflector

Energies ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4268
Author(s):  
Jessica de Wild ◽  
Gizem Birant ◽  
Guy Brammertz ◽  
Marc Meuris ◽  
Jef Poortmans ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Solar Cells ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Electron Microscopic ◽  
Current Increase ◽  
Time Resolved ◽  
Cigs Solar Cells

Ultrathin Cu(In,Ga)Se2 (CIGS) absorber layers of 550 nm were grown on Ag/AlOx stacks. The addition of the stack resulted in solar cells with improved fill factor, open circuit voltage and short circuit current density. The efficiency was increased from 7% to almost 12%. Photoluminescence (PL) and time resolved PL were improved, which was attributed to the passivating properties of AlOx. A current increase of almost 2 mA/cm2 was measured, due to increased light scattering and surface roughness. With time of flight—secondary ion mass spectroscopy, the elemental profiles were measured. It was found that the Ag is incorporated through the whole CIGS layer. Secondary electron microscopic images of the Mo back revealed residuals of the Ag/AlOx stack, which was confirmed by energy dispersive X-ray spectroscopy measurements. It is assumed to induce the increased surface roughness and scattering properties. At the front, large stains are visible for the cells with the Ag/AlOx back contact. An ammonia sulfide etching step was therefore applied on the bare absorber improving the efficiency further to 11.7%. It shows the potential of utilizing an Ag/AlOx stack at the back to improve both electrical and optical properties of ultrathin CIGS solar cells.

Enhancement of the performance of CdS/CdTe heterojunction solar cell using TiO2/ZnO bi-layer ARC and V2O5 BSF layers: A simulation approach

2020 ◽  
Vol 92 (2) ◽  
pp. 20901
Author(s):  
Abdul Kuddus ◽  
Md. Ferdous Rahman ◽  
Jaker Hossain ◽  
Abu Bakar Md. Ismail
Keyword(s):  
Solar Cell ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Heterojunction Solar Cell ◽  
Back Surface ◽  
Heterojunction Solar Cells

This article presents the role of Bi-layer anti-reflection coating (ARC) of TiO2/ZnO and back surface field (BSF) of V2O5 for improving the photovoltaic performance of Cadmium Sulfide (CdS) and Cadmium Telluride (CdTe) based heterojunction solar cells (HJSCs). The simulation was performed at different concentrations, thickness, defect densities of each active materials and working temperatures to optimize the most excellent structure and working conditions for achieving the highest cell performance using obtained optical and electrical parameters value from the experimental investigation on spin-coated CdS, CdTe, ZnO, TiO2 and V2O5 thin films deposited on the glass substrate. The simulation results reveal that the designed CdS/CdTe based heterojunction cell offers the highest efficiency, η of ∼25% with an enhanced open-circuit voltage, Voc of 0.811 V, short circuit current density, Jsc of 38.51 mA cm−2, fill factor, FF of 80% with bi-layer ARC and BSF. Moreover, it appears that the TiO2/ZnO bi-layer ARC, as well as ETL and V2O5 as BSF, could be highly promising materials of choice for CdS/CdTe based heterojunction solar cell.

Preparation of CuInGaSe2 Absorber Layer by Nanoparticles-Based Spray Deposition

2004 ◽  
Vol 836 ◽  
Author(s):  
Ki-Hyun Kim ◽  
Young-Gab Chun ◽  
Byung-Ok Park ◽  
Kyung-Hoon Yoon
Keyword(s):  
Spray Deposition ◽  
Soda Lime ◽  
Inert Atmosphere ◽  
Absorber Layer ◽  
Step Motor ◽  
Soda Lime Glass ◽  
Soda Lime Glass Substrate ◽  
Glass Substrates ◽  
Spray System ◽  
Cigs Nanoparticles

ABSTRACTCIGS nanoparticles for the CIGS absorber layer have been synthesized by low temperature colloidal routes. The CIGS absorber layers for solar cells have been prepared by spray deposition of CIGS nanoparticle precursors (∼20 nm) in glove box under inert atmosphere. An automatic air atomizing nozzle spray system with computer controlled X-Y step motor system was used to spray. The nanoparticle precursor CIGS film was deposited onto molybdenum-coated soda-lime glass substrates (2.5 cm × 5.0 cm) heated to 160°C. The film thickness in the range of 2 μm ± 0.3 μm was attained by spraying of 3 mM colloidal over an area of 12.5 cm2. The coalescence between particles was observed in the CIGS absorber layer under post-treatment of over 550 °C. This is related to the reactive sintering among the nanoparticles to reduce surface energy of the particles. The CuxSe thin film, formed on Mo film by evaporation, improved adhesion between CIGS and Mo layers and enhanced the coalescence of the particles in the CIGS layer. These are closely related to the fluxing of Cu2Se phase which has relatively low melting temperature. The CdS buffer layer was deposited on the CIGS/Mo/soda-lime glass substrate by chemical bath deposition. The CIGS nanoparticles-based absorber layers were characterized by using energy dispersive spectroscopy (EDS), x-ray diffraction (XRD) and high-resolution scanning electron microscopy (HRSEM).

IMPROVING STABILITY OF CHLOROPHYLL AS NATURAL DYE FOR DYE-SENSITIZED SOLAR CELLS

2017 ◽  
Vol 80 (1) ◽  
Author(s):  
Zainal Arifin ◽  
Sudjito Soeparman ◽  
Denny Widhiyanuriyawan ◽  
Suyitno Suyitno ◽  
Argatya Tara Setyaji
Keyword(s):  
Current Density ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Natural Dyes ◽  
Dye Sensitized ◽  
Sensitized Solar Cells

Natural dyes have attracted much researcher’s attention due to their low-cost production, simple synthesis processes and high natural abundance. However the dye-sensitized solar cells (DSSCs) based natural dyes have higher tendency to degradation. This article reports on the enhancement of performance and stability of dye-sensitized solar cells (DSSCs) using natural dyes. The natural dyes were extracted from papaya leaves by ethanol solvent at a temperature of 50 °C. Then the extracted dyes were isolated and modified into Mg-chlorophyll using column chromatography. Mg-chlorophyll was then synthesized into Fe-chlorophyll to improve stability. The natural dyes were characterized using ultraviolet-visible spectrometry, Fourier transform infrared spectroscopy, and cyclic voltammetry. The performance of DSSCs was tested using a solar simulator. The results showed the open-circuit voltage, the short-circuit current density, and the efficiency of the extracted papaya leaves-based DSSCs to be 325 mV, 0.36 mA/cm2, and 0.07%, respectively. Furthermore, the DSSCs with purified chlorophyll provide high open-circuit voltage of 425 mV and short-circuit current density of 0.45 mA/cm2. The use of Fe-chlorophyll for sensitizing the DSSCs increases the efficiency up to 2.5 times and the stability up to two times. The DSSCs with Fe-chlorophyll dyes provide open-circuit voltage, short-circuit current density, and efficiency of 500 mV, 0.62 mA/cm2, and 0.16%, respectively. Further studies to improve the current density and stability of natural dye-based DSSCs along with an improvement in the anchor between dyes and semiconducting layers are required.

scholarly journals Effects of Different Doping Ratio of Cu Doped CdS on QDSCs Performance

2015 ◽  
Vol 2015 ◽  
pp. 1-4
Author(s):  
Xiaojun Zhu ◽  
Xiaoping Zou ◽  
Hongquan Zhou
Keyword(s):  
Solar Cells ◽  
Quantum Dot ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Photoelectric Conversion Efficiency ◽  
Photoelectric Conversion ◽  
Sensitized Solar Cells ◽  
Doping Ratio

We use the successive ionic layer adsorption and reaction (SILAR) method for the preparation of quantum dot sensitized solar cells, to improve the performance of solar cells by doping quantum dots. We tested the UV-Vis absorption spectrum of undoped CdS QDSCs and Cu doped CdS QDSCs with different doping ratios. The doping ratios of copper were 1 : 100, 1 : 500, and 1 : 1000, respectively. The experimental results show that, under the same SILAR cycle number, Cu doped CdS quantum dot sensitized solar cells have higher open circuit voltage, short circuit current density photoelectric conversion efficiency than undoped CdS quantum dots sensitized solar cells. Refinement of Cu doping ratio are 1 : 10, 1 : 100, 1 : 200, 1 : 500, and 1 : 1000. When the proportion of Cu and CdS is 1 : 10, all the parameters of the QDSCs reach the minimum value, and, with the decrease of the proportion, the short circuit current density, open circuit voltage, and the photoelectric conversion efficiency are all increased. When proportion is 1 : 500, all parameters reach the maximum values. While with further reduction of the doping ratio of Cu, the parameters of QDSCs have a decline tendency. The results showed that, in a certain range, the lower the doping ratio of Cu, the better the performance of quantum dot sensitized solar cell.

scholarly journals Photoactive Layer of DSSCS Based on Natural Dyes: A Study of Experiment and Theory

2015 ◽  
Vol 2015 ◽  
pp. 1-6 ◽  
Author(s):  
Yuanzuo Li ◽  
Huixing Li ◽  
Peng Song ◽  
Chaofan Sun
Keyword(s):  
Density Functional ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Natural Dyes ◽  
Pheophytin A ◽  
Charge Difference Density ◽  
Forsythia Suspensa

Three natural dyes (Forsythia suspensa, Herba Violae, and Corn leaf) have been investigated as potential sensitizers for dye-sensitized solar cells. UV-vis absorption spectra reveal that three natural dyes mainly contain the compound of pheophytin a. Among three DSSCs, the highest photo electronic conversion efficiencyηis 0.96% with open circuit voltage (VOC) of 0.66 V, short circuit current density (ISC ) of 1.97 mA cm−2, and fill factor (ff) of 0.74. Theoretical time-dependent density functional theory and charge difference density are used to explore the nature of excited states. Results demonstrate that the first state is an intramolecular charge transfer (ICT) state, and electron injection could occur owing to the thermodynamically driving force.

scholarly journals Simulation of a perovskite sandwich solar cell with the p-CZTS / p-CH3NH3PbCI3 / p-CZTS absorber layers

2021 ◽  
Vol 877 (1) ◽  
pp. 012001
Author(s):  
Marwah S Mahmood ◽  
N K Hassan
Keyword(s):  
Solar Cell ◽  
Conversion Efficiency ◽  
Current Density ◽  
Short Circuit ◽  
Perovskite Solar Cells ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Current Voltage ◽  
Cell Capacitance

Abstract Perovskite solar cells attract the attention because of their unique properties in photovoltaic cells. Numerical simulation to the structure of Perovskite on p-CZTS/p-CH3NH3PbCI3/p-CZTS absorber layers is performed by using a program solar cell capacitance simulator (SCAPS-1D), with changing absorber layer thickness. The effect of thickness p-CZTS/p-CH3NH3PbCI3/p-CZTS, layers at (3.2μm, 1.8 μm, 1.1 μm) respectively are studied. The obtained results are short circuit current density (Jsc ), open circuit voltage (V oc), fill factor (F. F) and power conversion efficiency (PCE) equal to (28 mA/cm2, 0.83 v, 60.58 % and 14.25 %) respectively at 1.1 μm thickness. Our findings revealed that the dependence of current - voltage characteristics on the thickness of the absorbing layers, an increase in the amount of short circuit current density with an increase in the thickness of the absorption layers and thus led to an increase in the conversion efficiency and improvement of the cell by increasing the thickness of the absorption layers.

Sign in / Sign up

Export Citation Format

Share Document