RF Magnetron Sputtered Ba0.96Ca0.04Ti0.84Zr0.16O3 Thin Films for High Frequency Applications

2004 ◽  
Vol 833 ◽  
Author(s):  
Ali Mahmud ◽  
T. S. Kalkur ◽  
N. Cramer
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Dielectric Constant ◽  
Substrate Temperature ◽  
High Frequency ◽  
Satellite Communications ◽  
Ferroelectric Thin Films ◽  
Paraelectric State ◽  
Deposited Films

ABSTRACTPerovskite ferroelectric thin films in the paraelectric state exhibit outstanding dielectric properties, even at high frequencies (>1 GHz). The tunable dielectric constant of ferroelectric thin films can be used to design frequency and phase agile components. High dielectric constant thin film ferroelectric materials in the paraelectric state have received enormous attention due to their feasibility in applications such as decoupling capacitors and tunable microwave capacitors; the latter application has been fueled by the recent explosion in wireless and satellite communications. This paper reportsBa0.96Ca 0.04Ti0.84Zr0.16O3 (BCTZ) thin films that were deposited on Pt electrodes using radio frequency magnetron sputtering at a low (450 °C) substrate temperature. Sputtered thin film BCTZ at low substrate temperature is compatible with conventional integrated circuit technology. The structural characterization of the deposited films was performed by x-ray diffraction. The electrical characterization of the films was achieved by capacitance-voltage, current-voltage, and S-parameter (via vector network analyzer) measurements. In addition, the effect of post annealing on the deposited films was investigated. A detailed understanding of both their processing and material properties is discussed for successful implementation in high frequency applications.

Preparation and Characterization of MFM and MFIS Structures Using Sr2(Ta1划x, Nbx)2O7 Thin Film by Pulsed Laser Deposition

2000 ◽  
Vol 655 ◽  
Author(s):  
Masanori Okuyama ◽  
Toshiyuki Nakaiso ◽  
Minoru Noda
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Pulsed Laser ◽  
Ferroelectric Thin Films ◽  
Laser Deposition ◽  
Polarization Reversal ◽  
Ambient Gas ◽  
Mfis Structure

AbstractSr2(Ta1划x, Nbx)2O7(STN) ferroelectric thin films have been prepared on SiO2/Si(100) substrates by the pulsed laser deposition (PLD) method. Preferential (110) and (151)-oriented STN thin films are deposited at a low temperature of 600°C in N2O ambient gas at 0.08 Torr. A counterclockwise C-V hysteresis was observed in the metal-ferroelectric-insulator-semiconductor (MFIS) structure using Sr2(Ta0.7, Nb0.3)2O7 on SiO2/Si deposited at 600°C. Memory window in the C-V curve spreads symmetrically towards both positive and negative directions when applied voltage increases and the window does not change in sweep rates ranging from 0.1 to 4.0×103 V/s. The C-V curve of the MFIS structure does not degrade after 1010 cycles of polarization reversal. The gate retention time is about 3.0×103 sec when the voltages and time of write pulse are ±15V and 1.0 sec, respectively, and hold bias was -0.5 V.

Optical Characterization of LaF3 by Variable Angle Purged UV Spectroscopic Ellipsometry

2013 ◽  
Vol 662 ◽  
pp. 243-248
Author(s):  
Wen Yuan Deng
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Substrate Temperature ◽  
Optical Characterization ◽  
Theory Model ◽  
Material Dispersion ◽  
Optical Index ◽  
Variable Angle ◽  
Selection Of

The optical characterization of LaF3 thin film in DUV spectral range was experimental investigated by using a variable angle purged UV spectroscopic ellipsometer. In order to take into account the inhomogeneity, a theory model that dividing the single thin film into several sublayers was adopted. Two kinds of LaF3 thin films fabricated on fused silicate substrate with different substrates temperature were tested. From the obtained optical index and the physical thickness of different sublayer in the two different kinds of LaF3 thin films, it was found that, the inhomogeneity of the LaF3 thin film deposited with substrate temperature at 300°C was stronger than that of the LaF3 thin film deposited with substrate temperature at 250°C, indicating that the substrate temperature has important influence on the optical index and inhomogeneity of LaF3 thin films. For both of the two kinds LaF3 thin films, the agreement between the measured transmittance and the simulated transmittance using the parameters from regression of SE was nice, indicating that the selection of the material dispersion law and regression procedure were successful.

Characterization of Ferroelectric Property of c-axis and non-c-axis Oriented Epitaxially Grown Bismuth Layer-Structured Ferroelectric Thin Films with Different m-numbers Prepared by MOCVD

2000 ◽  
Vol 655 ◽  
Author(s):  
Takayuki Watanabe ◽  
Tomohiro Sakai ◽  
Atsushi Saiki ◽  
Keisuke Saito ◽  
Toyohiko Chikyo ◽  
...  
Keyword(s):  
Thin Films ◽  
Dielectric Constant ◽  
Leakage Current ◽  
Ferroelectric Property ◽  
Metalorganic Chemical Vapor Deposition ◽  
Chemical Vapor ◽  
Epitaxial Thin Films ◽  
Oriented Film ◽  
Deposited Films

AbstractEpitaxial thin films of bismuth layer-structured ferroelectrics (BLSF) with different m-numbers, i.e., Bi2VO5.5 (BVO) (m=1), SrBi2Ta2O9 (SBT) (m=2), and Bi4Ti3O12 (BIT) (m=3), were grown by metalorganic chemical vapor deposition (MOCVD). (00l)-oriented films were deposited on (100)SrTiO3. (114)-oriented BVO, (116)-oriented SBT, and (118)-oriented BIT films were deposited on (110)SrTiO3. Moreover, (102)-oriented BVO, (103)-oriented SBT, and (104)-oriented BIT films were deposited on (111)SrTiO3. On (100), (110), and (111)SrTiO3 substrates, c-axis of the deposited films was tilted about 0°, 45°, and 56°, respectively, against perpendicular to the surface of the substrates irrespective of m-number. This suggests the growth of crystallographic equivalent orientation. The distinctive surface morphology originated to the feature of the film orientation was observed. The dielectric constant and the leakage current of c-axis-oriented film was smaller than that of non-c-axis-oriented one, indicating smaller dielectric constant and leakage current along c-axis than a- or b-axes. A larger ferroelectric anisotropy was ascertained for SBT and BIT films. Furthermore, the evaluated spontaneous polarization along a- and c- axes of BIT from the data of the epitaxially grown BIT films well agreed with the reported one for the single crystal. This suggests the ferroelectric property was not strongly affected by the strain in the films.

Recursive Image Charge Approach for Quantitative Characterization of Dielectric Thin Film Library Using Scanning Tip Microwave Near-field Microscopy

2003 ◽  
Vol 804 ◽  
Author(s):  
Chen Gao ◽  
Bo Hu ◽  
Mengming Huang ◽  
Pu Zhang ◽  
Wen-han Liu
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Dielectric Constant ◽  
Near Field ◽  
Image Charge ◽  
Film Library ◽  
Quantitative Characterization ◽  
Dielectric Thin Films ◽  
Dielectric Thin Film

ABSTRACTWe developed a recursive image charge approach for quantitative characterizations of dielectric thin films using the scanning tip microwave near-field microscope. With this method, frequency shift of the microscope as functions of the dielectric constant and the thickness of a film can be effectively computed in a recursive way. We believe that this approach can promote the high-throughput characterization of the dielectric libraries.

scholarly journals Characterization of Thermally Evaporated Ag-Ge-S Thin Films

2008 ◽  
Vol 1072 ◽  
Author(s):  
Fei Wang ◽  
William Porter Dunn ◽  
Mukul Jain ◽  
Carter De Leo ◽  
Nicholas Vicker ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Raman Spectroscopy ◽  
Film Thickness ◽  
Raman Line ◽  
Line Shapes ◽  
Thermal Evaporator ◽  
Bulk Glasses ◽  
Deposited Films

ABSTRACTThin films of ternary (GeS3)1−xAgx glasses (x=0.1 and 0.2) are studied in this work. Thin films are fabricated in a vacuum thermal evaporator at 3 different evaporation angles (0°, 30° and 45°). All thin film samples are examined in Raman spectroscopy. Raman results of both normally and obliquely deposited thin film samples reveal Ge-S CS modes (∼340cm−1) , Ge-S ES (∼360cm−1) modes, and thiogermanate modes Q1∼Q3 (390cm−1∼437cm−1). In addition, sharp peaks due to sulfur rings (S8) are observed at 218cm−1 and 470cm−1. Raman line-shapes of thin films are qualitatively consistent with their corresponding bulk glasses. However, the sharp peaks due to sulfur rings were not observed in bulk glasses. By comparing CS modes of thin films of three angles, we observe that normally deposited (0 degree) thin film shows a red-shift in center and a broadening in width. The film thickness of normally deposited films are significantly smaller comparing with that of corresponding obliquely deposited films.

The Microstructure and Giant Magnetoresistance of NiFeAg Thin Films

1993 ◽  
Vol 313 ◽  
Author(s):  
Michael A. Parker ◽  
K. R. Coffey ◽  
T. L. Hylton ◽  
J. K. Howard
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Grain Growth ◽  
Giant Magnetoresistance ◽  
Microstructural Characterization ◽  
Structure Property ◽  
Structure Property Relationships ◽  
Deposited Films

ABSTRACTAlthough Much has been published on giant Magnetoresistance (GMR) in co-deposited thin films [1–4], only little [5] has been published on the structure-property relationships limiting the effect. Here, we report the results of microstructural characterization of NiFeAg thin films that exhibit a GMR effect. The as-deposited films show a sizeable GMR effect. The Maximum GMR effect observed was 6.4% with -4k0e FWHM of the 6P/P peak. Upon annealing these films, the GMR at first increases, and then decreases. We present microstructural evidence from TEM and XRD, amongst other techniques, which shows that this is a consequence of the initial NiFeAg thin film agglomerating into NiFe grains in a predominantly Ag segregant Matrix. Upon extended annealing, excessive grain growth leads to a decrease in the GMR as predicted by the model of Berkowitz, et al. [1].

scholarly journals Fabrication, micro-structure characteristics and transport properties of co-evaporated thin films of Bi2Te3 on AlN coated stainless steel foils

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Aziz Ahmed ◽  
Seungwoo Han
Keyword(s):  
Thin Film ◽  
Crystal Structure ◽  
Thin Films ◽  
Stainless Steel ◽  
Substrate Temperature ◽  
Transport Properties ◽  
Structural Defects ◽  
Film Composition ◽  
High Substrate ◽  
Foil Substrate

AbstractN-type bismuth telluride (Bi2Te3) thin films were prepared on an aluminum nitride (AlN)-coated stainless steel foil substrate to obtain optimal thermoelectric performance. The thermal co-evaporation method was adopted so that we could vary the thin film composition, enabling us to investigate the relationship between the film composition, microstructure, crystal preferred orientation and thermoelectric properties. The influence of the substrate temperature was also investigated by synthesizing two sets of thin film samples; in one set the substrate was kept at room temperature (RT) while in the other set the substrate was maintained at a high temperature, of 300 °C, during deposition. The samples deposited at RT were amorphous in the as-deposited state and therefore were annealed at 280 °C to promote crystallization and phase development. The electrical resistivity and Seebeck coefficient were measured and the results were interpreted. Both the transport properties and crystal structure were observed to be strongly affected by non-stoichiometry and the choice of substrate temperature. We observed columnar microstructures with hexagonal grains and a multi-oriented crystal structure for the thin films deposited at high substrate temperatures, whereas highly (00 l) textured thin films with columns consisting of in-plane layers were fabricated from the stoichiometric annealed thin film samples originally synthesized at RT. Special emphasis was placed on examining the nature of tellurium (Te) atom based structural defects and their influence on thin film properties. We report maximum power factor (PF) of 1.35 mW/m K2 for near-stoichiometric film deposited at high substrate temperature, which was the highest among all studied cases.

Al1-x ScxN Thin Film Structures for Pyroelectric Sensing Applications

MRS Advances ◽  
2016 ◽  
Vol 1 (39) ◽  
pp. 2711-2716 ◽  
Author(s):  
V. Vasilyev ◽  
J. Cetnar ◽  
B. Claflin ◽  
G. Grzybowski ◽  
K. Leedy ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Pyroelectric Coefficient ◽  
X Ray Diffraction ◽  
Ir Detectors ◽  
Pyroelectric Properties ◽  
X Ray ◽  
Sensing Applications ◽  
Pyroelectric Material ◽  
Deposited Films

ABSTRACTAlN thin film structures have many useful and practical piezoelectric and pyroelectric properties. The potential enhancement of the AlN piezo- and pyroelectric constants allows it to compete with more commonly used materials. For example, combination of AlN with ScN leads to new structural, electronic, and mechanical characteristics, which have been reported to substantially enhance the piezoelectric coefficients in solid-solution AlN-ScN compounds, compared to a pure AlN-phase material.In our work, we demonstrate that an analogous alloying approach results in considerable enhancement of the pyroelectric properties of AlN - ScN composites. Thin films of ScN, AlN and Al1-x ScxN (x = 0 – 1.0) were deposited on silicon (004) substrates using dual reactive sputtering in Ar/N2 atmosphere from Sc and Al targets. The deposited films were studied and compared using x-ray diffraction, XPS, SEM, and pyroelectric characterization. An up to 25% enhancement was observed in the pyroelectric coefficient (Pc = 0.9 µC /m2K) for Sc1-xAlxN thin films structures in comparison to pure AlN thin films (Pc = 0.71 µC/m2K). The obtained results suggest that Al1-x ScxN films could be a promising novel pyroelectric material and might be suitable for use in uncooled IR detectors.

The Ferroelectric and Electrical Properties of CaBi4Ti4O15 Thin Films Prepared by Sol-Gel Technology

2011 ◽  
Vol 239-242 ◽  
pp. 891-894 ◽  
Author(s):  
Tsung Fu Chien ◽  
Jen Hwan Tsai ◽  
Kai Huang Chen ◽  
Chien Min Cheng ◽  
Chia Lin Wu
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Sol Gel ◽  
Morphological Characterization ◽  
Experimental Result ◽  
X Ray Diffraction ◽  
Solution Deposition ◽  
Capacitance Voltage ◽  
Preferential Crystal Orientation

In this study, thin films of CaBi4Ti4O15with preferential crystal orientation were prepared by the chemical solution deposition (CSD) technique on a SiO2/Si substrate. The films consisted of a crystalline phase of bismuth-layer-structured dielectric. The as-deposited CaBi4Ti4O15thin films were crystallized in a conventional furnace annealing (RTA) under the temperature of 700 to 800°C for 1min. Structural and morphological characterization of the CBT thin films were investigated by X-ray diffraction (XRD) and field-emission scanning electron microscope (FE-SEM). The impedance analyzer HP4294A and HP4156C semiconductor parameters analyzer were used to measurement capacitance voltage (C-V) characteristics and leakage current density of electric field (J-E) characteristics by metal-ferroelectric-insulator- semiconductor (MFIS) structure. By the experimental result the CBT thin film in electrical field 20V, annealing temperature in 750°C the CBT thin film leaks the electric current is 1.88x10-7A/cm2and the memory window is 1.2V. In addition, we found the strongest (119) peak of as-deposited thin films as the annealed temperature of 750°C

Sign in / Sign up

Export Citation Format

Share Document