scholarly journals Diffusion-mediated chemical concentration variation and void evolution in ion-irradiated NiCoFeCr high-entropy alloy

2021 ◽  
Vol 36 (1) ◽  
pp. 298-310
Author(s):  
Zhe Fan ◽  
Weicheng Zhong ◽  
Ke Jin ◽  
Hongbin Bei ◽  
Yuri N. Osetsky ◽  
...  

AbstractHigh-entropy alloys (HEAs) are proposed as potential structural materials for advanced nuclear systems, but little is known about the response of matrix chemistry in HEAs upon irradiation. Here, we reveal a substantial change of matrix chemical concentration as a function of irradiation damage (depth) in equiatomic NiCoFeCr HEA irradiated by 3 MeV Ni ions. After ion irradiation, the matrix contains more Fe/Cr in depth shallower than ~900–1000 nm but more Ni/Co from ~900–1000 nm to the end of the ion-damaged region due to the preferential diffusion of vacancies through Fe/Cr. Preferential diffusion also facilitates migration of vacancies from high radiation damage region to low radiation damage region, leading to no void formation below ~900–1000 nm and void formation around the end of the ion-damaged region at a fluence of 5 × 1016 cm−2 (~123 dpa, displacements per atom, peak dose under full cascade mode). As voids grow significantly at an increased fluence (8 × 1016 cm−2, 196 dpa), the matrix concentration does not change dramatically due to new voids formed below ~900–1000 nm.

2022 ◽  
Vol 892 ◽  
pp. 162043
Author(s):  
Shengyuan Peng ◽  
Ke Jin ◽  
Xin Yi ◽  
Zhaohui Dong ◽  
Xun Guo ◽  
...  

2021 ◽  
Vol 871 ◽  
pp. 3-8
Author(s):  
Rui Zhi Jian ◽  
Shang Cheng Zhou ◽  
Yun Fei Xue

To improve the mechanical properties of a sintered WHA using high entropy alloy as the matrix (W-HEA), investigations were carried out to apply deformation strengthening method of hot swaging on the W-HEA. The W-HEA samples were swaged around 1300°C with the 10%, 15% and 20% of reduction in area. The results show that the strength and hardness of the W-HEA composite increased with the increasing degree of deformation. And the aspect ratio of tungsten grains increases along the axial direction in the swaged alloys. The hardness of W-HEA with a 20% reduction in area reaches 448 HV, and the dynamic compression yield strength is about 1911 MPa. After hot swaging, the hardness and strength of the W-HEA are greatly improved compared with the sintered W-HEA.


2020 ◽  
Vol 25 ◽  
pp. 100813 ◽  
Author(s):  
M. Aizenshtein ◽  
Z. Ungarish ◽  
K.B. Woller ◽  
S. Hayun ◽  
M.P. Short

2016 ◽  
Vol 113 ◽  
pp. 230-244 ◽  
Author(s):  
N.A.P. Kiran Kumar ◽  
C. Li ◽  
K.J. Leonard ◽  
H. Bei ◽  
S.J. Zinkle

2019 ◽  
Vol 35 (3) ◽  
pp. 300-305 ◽  
Author(s):  
Lixin Yang ◽  
Hualong Ge ◽  
Jian Zhang ◽  
Ting Xiong ◽  
Qianqian Jin ◽  
...  

2020 ◽  
pp. 1-13 ◽  
Author(s):  
Zhe Fan ◽  
Weicheng Zhong ◽  
Ke Jin ◽  
Hongbin Bei ◽  
Yuri N. Osetsky ◽  
...  

Abstract


Entropy ◽  
2019 ◽  
Vol 21 (5) ◽  
pp. 448 ◽  
Author(s):  
Cui Zhang ◽  
Bin Liu ◽  
Yong Liu ◽  
Qihong Fang ◽  
Wenmin Guo ◽  
...  

A CoCrFeNiMo0.2 high entropy alloy (HEA) was prepared through powder metallurgy (P/M) process. The effects of annealing on microstructural evolution and mechanical properties of P/M HEAs were investigated. The results show that the P/M HEA exhibit a metastable FCC single-phase structure. Subsequently, annealing causes precipitation in the grains and at the grain boundaries simultaneously. As the temperature increases, the size of the precipitates grows, while the content of the precipitates tends to increase gradually first, and then decrease as the annealing temperature goes up to 1000 °C. As the annealing time is prolonged, the size and content of the precipitates gradually increases, eventually reaching a saturated stable value. The mechanical properties of the annealed alloys have a significant correspondence with the precipitation behavior. The larger the volume fraction and the size of the precipitates, the higher the strength and the lower the plasticity of the HEA. The CoCrFeNiMo0.2 high entropy alloy, which annealed at 800 °C for 72 h, exhibited the most excellent mechanical properties with the ultimate tensile strength of about 850 MPa and an elongation of about 30%. Nearly all of the annealed HEAs exhibit good strength–ductility combinations due to the significant precipitation enhancement and nanotwinning. The separation of the coarse precipitation phase and the matrix during the deformation process is the main reason for the formation of micropores. Formation of large volume fraction of micropores results in a decrease in the plasticity of the alloy.


2020 ◽  
Vol 531 ◽  
pp. 152005 ◽  
Author(s):  
Dhinisa Patel ◽  
Mark D. Richardson ◽  
Bethany Jim ◽  
Shavkat Akhmadaliev ◽  
Russell Goodall ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document