scholarly journals Corn crop performance in an Ultisol compacted by tractor traffic

2018 ◽  
Vol 53 (4) ◽  
pp. 464-477 ◽  
Author(s):  
Moacir Tuzzin de Moraes ◽  
Renato Levien ◽  
Carlos Ricardo Trein ◽  
João de Andrade Bonetti ◽  
Henrique Debiasi

Abstract: The objective of this work was to determine whether compaction by tractor traffic in areas managed under controlled traffic can be limiting to corn crop, under different tillage systems, in a Typic Paleudult of medium texture. Two experiments were carried out, one in the field over two crop seasons and another in a greenhouse. The treatments consisted of minimum tillage with chiselling; no-tillage subjected to one, three, or six passes of a tractor weighing 3.8 Mg; and an area without traffic. Evaluations were performed for soil physico-hydraulic parameters (soil bulk density, penetration resistance, and water retention curve), root and shoot growth, and grain yield. The agricultural traffic increased bulk density, soil penetration resistance, and water content at field capacity. The highest values for soil penetration resistance (1,600 kPa) and bulk density (1.67 g cm-3) in the trafficked soil were not limiting to corn development and increased grain yield for both crop seasons. Tractor traffic of up to six passes is beneficial to corn cultivation, and it increases water availability and corn grain yield.

2015 ◽  
Vol 29 (4) ◽  
pp. 441-447 ◽  
Author(s):  
Michel Keisuke Sato ◽  
Herdjania Veras de Lima ◽  
Pedro Daniel de Oliveira ◽  
Sueli Rodrigues

Abstract The aim of this study was to evaluate the critical soil bulk density from the soil penetration resistance measurements for soybean root growth in Brazilian Amazon Oxisols. The experiment was carried out in a greenhouse using disturbed soil samples collected from the northwest of Para characterized by different texture. The treatments consisted of a range of soil bulk densities for each soil textural class. Three pots were used for soybean growth of and two for the soil penetration resistance curve. From the fitted model, the critical soil bulk density was determined considering the penetration resistance values of 2 and 3 MPa. After sixty days, plants were cut and root length, dry mass of root, and dry mass of shoots were determined. At higher bulk densities, the increase in soil water content decreased the penetration resistance, allowing unrestricted growth of soybean roots. Regardless of soil texture, the penetration resistance of 2 and 3 MPa had a slight effect on root growth in soil moisture at field capacity and a reduction of 50% in the soybean root growth was achieved at critical soil bulk density of 1.82, 1.75, 1.51, and 1.45 Mg m-3 for the sandy loam, sandy clay loam, clayey, and very clayey soil.


2011 ◽  
Vol 91 (6) ◽  
pp. 957-964 ◽  
Author(s):  
C. Halde ◽  
A. M. Hammermeister ◽  
N. L. Mclean ◽  
K. T. Webb ◽  
R. C. Martin

Halde, C., Hammermeister, A. M., McLean, N. L., Webb, K. T. and Martin, R. C. 2011. Soil compaction under varying rest periods and levels of mechanical disturbance in a rotational grazing system. Can. J. Soil Sci. 91: 957–964. In Atlantic Canada, data are limited regarding the effect of grazing systems on soil compaction. The objective of the study was to determine the effect of intensive and extensive rotational pasture management treatments on soil bulk density, soil penetration resistance, forage productivity and litter accumulation. The study was conducted on a fine sandy loam pasture in Truro, Nova Scotia. Each of the eight paddocks was divided into three rotational pasture management treatments: intensive, semi-intensive and extensive. Mowing and clipping were more frequent in the intensive than in the semi-intensive treatment. In the extensive treatment, by virtue of grazing in alternate rotations, the rest period was doubled than that of the intensive and semi-intensive treatments. Both soil bulk density (0–5 cm) and penetration resistance (0–25.5 cm) were significantly higher in the intensive treatment than in the extensive treatment, for all seasons. Over winter, bulk density decreased significantly by 6.8 and 3.8% at 0–5 and 5–10 cm, respectively. A decrease ranging between 40.5 and 4.0% was observed for soil penetration resistance over winter, at 0–1.5 cm and 24.0–25.5 cm, respectively. The intensive and semi-intensive treatments produced significantly more available forage for grazers annually than the extensive treatment. Forage yields in late May to early June were negatively correlated with spring bulk density.


2016 ◽  
Vol 36 (3) ◽  
pp. 449-459 ◽  
Author(s):  
Wininton M. da Silva ◽  
Aloísio Bianchini ◽  
Cesar A. da Cunha

ABSTRACT This study aimed to describe the behavior of models for adjusting data of soil penetration resistance for variations in soil moisture and soil bulk density. The study was carried out in Lucas do Rio Verde, MT, Brazil in a typic dystrophic red-yellow Latosol (Oxisol) containing 0.366 kg kg−1 of clay. Soil penetration resistance measurements were conducted in the soil moistures of 0.33 kg kg−1, 0.28 kg kg−1, 0.25 kg kg−1 and 0.22 kg kg−1. Soil penetration resistance behavior due to variations in soil moisture and soil bulk density was assessed by estimating the soil resistance values by non-linear models. There was an increase of the soil penetration resistance values as soil was losing moisture. For the same edaphic condition studied, small differences in the data of soil bulk density affect differently the response of soil resistance as a function of moisture. Both soil bulk density and soil moisture are essential attributes to explain the variations in soil penetration resistance in the field. The good representation of the critical soil bulk density curve as a limiting compression indicator requires the proper choice of the restrictive soil resistance value for each crop.


Bragantia ◽  
2014 ◽  
Vol 73 (2) ◽  
pp. 171-177 ◽  
Author(s):  
Daniel Dias Valadão Junior ◽  
Aloísio Biachini ◽  
Franciele Caroline Assis Valadão ◽  
Rodrigo Pengo Rosa

This study aimed to evaluate the effect of penetration rate and the size of the cone base on the resistance to penetration under different soil moistures and soil bulk density. The experimental design was completely randomized in a 4x2x2x2 factorial arrangement, with the factors, soil bulk density of 1.0; 1.2; 1.4 and 1.6 Mg m-3, soil moisture at the evaluation of 0.16 and 0.22 kg kg-1, penetration rates of 0.166 and 30 mm s-1 and areas of the cone base of 10.98 and 129.28 mm² resulting in 32 treatments with 8 replicates. To ensure greater uniformity and similarity to field conditions, samples passed through cycles of wetting and drying. Only the interaction of the four factors was not significant. Resistance values varied with the density of the soil, regardless of moisture and penetration rate. Soil penetration resistance was influenced by the size of the cone base, with higher values for the smallest base independent of moisture and soil bulk density. The relationship between resistance to penetration and moisture is not always linear, once it is influenced by soil bulk density. Reduction in the area of the cone leads to an increase in the soil resistance to penetration.


2019 ◽  
Vol 49 (2) ◽  
pp. 164-178 ◽  
Author(s):  
Eric R. Labelle ◽  
Benjamin J. Poltorak ◽  
Dirk Jaeger

Forest soils often exhibit low bearing capacities and as a result are often incapable of withstanding high axle loads. In New Brunswick, Canada, five different brush amounts (0, 5, 10, 15, and 20 kg·m–2) were applied as brush mats on machine operating trails during a cut-to-length harvesting operation in a softwood stand to analyze soil disturbance as a result of off-road forest harvesting machine traffic. Soil absolute and relative bulk density and soil penetration resistance measurements were completed below the varying brush mats both before and after forwarding. The mean differences between pre- and post-impact absolute soil dry bulk density values recorded on track areas were 0.24 g·cm–3 for 5–20 kg·m–2 of brush and 0.33 g·cm–3 for 0 kg·m–2 of brush. On average, 40.5%, 17.9%, 14.3%, 15.5%, and 3.6% of all post-forwarding measurements exceeded the threshold for growth-impeding soil bulk density (80% standard Proctor density) for 0, 5, 10, 15 and 20 kg·m–2 of brush, respectively. Soil penetration values >3.0 MPa represented 23.7%, 15.0%, 9.4%, 4.6%, and 0.7% of all post-forwarding test plots with 0, 5, 10, 15, and 20 kg·m–2 of brush, respectively. The results suggest that softwood brush mats of 10 to 20 kg·m–2 placed on machine operating trails play a considerable role in reducing forwarder-induced soil compaction and penetration resistance.


Soil Research ◽  
2012 ◽  
Vol 50 (6) ◽  
pp. 455 ◽  
Author(s):  
V. P. Pereira ◽  
M. E. Ortiz-Escobar ◽  
G. C. Rocha ◽  
R. N. Assis Junior ◽  
T. S. Oliveira

Concern about soil physical quality has grown in recent years, particularly in view of serious problems caused by intensive soil use. We hypothesised that improper soil management in irrigated areas damages the structure of sensitive soils in some regions in North-eastern Brazil. The aim of the study was to evaluate the physical quality of irrigated soils planted with annual and perennial crops, compared with soils under natural vegetation in Ceará State, Brazil. Measurements were made of least limiting water range (LLWR), the S index, and relative density. Undisturbed soil samples were collected at two depths (5–10 and 20–25 cm) in four cultivated areas (banana, guava, pasture, and maize/bean in succession) and two natural vegetation areas (NV1, NV2) adjacent to the cultivated areas. All sites were in the Jaguaribe-Apodi Irrigated District, Limoeiro do Norte, Ceará, Brazil. The LLWR was determined using the water retention curve, soil resistance to penetration, and soil bulk density, which are parameters needed to obtain the upper and lower limits of LLWR. The S index was obtained from the water retention curve. The relative density was obtained from the relationship between bulk density and maximum density obtained from the Proctor test. The S index varied as a function of soil management. The variation in LLWR differed between the studied areas as a function of soil bulk density. The relative densities for NV1 and NV2 were lower than for cultivated areas, showing that intensive soil use has caused compaction. The studied parameters seem to be good indicators of soil physical quality, and it was noticed that soils under cultivation suffer an alteration of their structure relative to soils under natural vegetation.


Soil Research ◽  
1988 ◽  
Vol 26 (2) ◽  
pp. 391 ◽  
Author(s):  
C Henderson ◽  
A Levett ◽  
D Lisle

Quantitative models to predict the effects of soil compaction on wheat yields are being developed for the northern sandplains of Western Australia. An understanding of the relationships between soil water content (W), bulk density (p), compactibility and soil penetration resistance (P) is required. Thirteen subsoils from W.A. sandplain soils were tested for compactibility. As the amounts of very coarse sand or clay in the soil increased, the maximum density (�max.) achieved with a standard compactive effort also increased, while the critical soil water content (Wcrit,.) for maximum compactibility declined. The effects of p and W on P were investigated for five of the soils. The value of P was only slightly affected as W was reduced to less than 70% of the field capacity water content. As the soils were dried further, P increased exponentially. At all water contents, an increase in p was found to markedly increase P. Particle size distribution could be used to predict �max. and Wcrit., but could not be related to the effects of changes in p and W on P. The implications for the measurement and effects of soil compaction in the field are discussed.


Agronomy ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 578
Author(s):  
Dariusz Błażejczak ◽  
Jan Jurga ◽  
Jarosław Pytka

The aim of this work was to develop a method of data grouping (DGM) that enables the selection of regression equations for forecasting soil penetration resistance based on an easily available and small set of input data: soil moisture content, soil bulk density and the grain size distribution of the soil. Models for forecasting the penetration resistance were created by selecting regression equations for specific intervals of granulometric variability of soil fractions. A field measurements campaign was conducted and soil samples were taken from the subsoil on 43 profiles, at depths of 25–30, 35–40, 45–50 and 55–60 cm. It was found that the dry bulk density is much less useful for predicting the penetration resistance of plastic soils than soil moisture. The study also showed that it is possible to forecast the soil penetration resistance on the basis of the gravimetric moisture content and the soil specific surface.


Soil Research ◽  
2014 ◽  
Vol 52 (6) ◽  
pp. 521 ◽  
Author(s):  
O. Guedes Filho ◽  
A. P. da Silva ◽  
N. F. B. Giarola ◽  
C. A. Tormena

Physical quality of the soil seedbed affects germination, seedling emergence and crop establishment. The aim of this work was to determine the least-limiting water range (LLWR) of a soil seedbed cultivated for 18 consecutive years under no-till (NT) and submitted to mechanical chiselling (NT-M) and biological chiselling by a forage radish cover crop (NT-B). The study was carried out in Ponta Grossa, Paraná, Brazil. The experimental design was randomised complete blocks with four replications. Soil samples at 0–5 and 5–10 cm depths were collected at 6 and 18 months after the start of the experiment which corresponded to maize (October 2009) and soybean (November 2010) planting. Water-retention curve, penetration-resistance curve, soil and relative bulk density, and LLWR were determined. Bulk density did not differ among treatments at 0–5 cm depth for both evaluation periods. At 5–10 cm soil depth, the NT-M treatment showed the lowest bulk density at the first sampling (2009), whereas NT-B showed the highest bulk density at the second sampling (2010). Soil penetration resistance was the most limiting factor of the LLWR, which was greater in NT-M for both soil layers at the first sampling. At the second sampling, the NT treatment had the greatest LLWR at 0–5 cm, but at 5–10 cm soil depth, both NT and NT-M had higher LLWR than NT-B. The efficiency of mechanical chiselling in improving soil seedbed physical quality lasted 18 months after its application. Biological chiselling was efficient in improving soil air-filled porosity in both periods as evaluated by the LLWR.


Sign in / Sign up

Export Citation Format

Share Document