The role of brush mats in mitigating machine-induced soil disturbances: an assessment using absolute and relative soil bulk density and penetration resistance

2019 ◽  
Vol 49 (2) ◽  
pp. 164-178 ◽  
Author(s):  
Eric R. Labelle ◽  
Benjamin J. Poltorak ◽  
Dirk Jaeger

Forest soils often exhibit low bearing capacities and as a result are often incapable of withstanding high axle loads. In New Brunswick, Canada, five different brush amounts (0, 5, 10, 15, and 20 kg·m–2) were applied as brush mats on machine operating trails during a cut-to-length harvesting operation in a softwood stand to analyze soil disturbance as a result of off-road forest harvesting machine traffic. Soil absolute and relative bulk density and soil penetration resistance measurements were completed below the varying brush mats both before and after forwarding. The mean differences between pre- and post-impact absolute soil dry bulk density values recorded on track areas were 0.24 g·cm–3 for 5–20 kg·m–2 of brush and 0.33 g·cm–3 for 0 kg·m–2 of brush. On average, 40.5%, 17.9%, 14.3%, 15.5%, and 3.6% of all post-forwarding measurements exceeded the threshold for growth-impeding soil bulk density (80% standard Proctor density) for 0, 5, 10, 15 and 20 kg·m–2 of brush, respectively. Soil penetration values >3.0 MPa represented 23.7%, 15.0%, 9.4%, 4.6%, and 0.7% of all post-forwarding test plots with 0, 5, 10, 15, and 20 kg·m–2 of brush, respectively. The results suggest that softwood brush mats of 10 to 20 kg·m–2 placed on machine operating trails play a considerable role in reducing forwarder-induced soil compaction and penetration resistance.

Forests ◽  
2022 ◽  
Vol 13 (1) ◽  
pp. 109
Author(s):  
Michal Allman ◽  
Zuzana Dudáková ◽  
Martin Jankovský ◽  
Mária Vlčková ◽  
Vladimír Juško ◽  
...  

Soil disturbance and compaction are inherent in ground-based harvesting operations. These changes are affected by numerous factors, related mainly to the technical parameters of the machines, soil conditions, and the technology used. This study aimed to analyze the changes of surface layers of soil caused by skidder traffic without loads on the Cambisols of Western Carpathians. We observed changes in the soil bulk density and penetration resistance. The results showed that only machine traffic caused a 0.32 to 0.35 (g cm−3) increase in soil bulk density. Besides machine traffic, bulk density was affected by soil moisture content. Penetration resistance of soil increased by 0.15 to 1.04 (MPa) after traffic of 40 machines. Penetration resistance showed a lower increase after traffic, and regression and correlation analysis proved a relationship between penetration resistance, skeleton content, and penetration depth, besides the number of machine passes (r = 0.33–0.55). Observing the changes in the physical properties of soils caused by machine traffic allows for a more detailed view of the effects of forest harvesting machinery on forest soils.


2011 ◽  
Vol 91 (6) ◽  
pp. 957-964 ◽  
Author(s):  
C. Halde ◽  
A. M. Hammermeister ◽  
N. L. Mclean ◽  
K. T. Webb ◽  
R. C. Martin

Halde, C., Hammermeister, A. M., McLean, N. L., Webb, K. T. and Martin, R. C. 2011. Soil compaction under varying rest periods and levels of mechanical disturbance in a rotational grazing system. Can. J. Soil Sci. 91: 957–964. In Atlantic Canada, data are limited regarding the effect of grazing systems on soil compaction. The objective of the study was to determine the effect of intensive and extensive rotational pasture management treatments on soil bulk density, soil penetration resistance, forage productivity and litter accumulation. The study was conducted on a fine sandy loam pasture in Truro, Nova Scotia. Each of the eight paddocks was divided into three rotational pasture management treatments: intensive, semi-intensive and extensive. Mowing and clipping were more frequent in the intensive than in the semi-intensive treatment. In the extensive treatment, by virtue of grazing in alternate rotations, the rest period was doubled than that of the intensive and semi-intensive treatments. Both soil bulk density (0–5 cm) and penetration resistance (0–25.5 cm) were significantly higher in the intensive treatment than in the extensive treatment, for all seasons. Over winter, bulk density decreased significantly by 6.8 and 3.8% at 0–5 and 5–10 cm, respectively. A decrease ranging between 40.5 and 4.0% was observed for soil penetration resistance over winter, at 0–1.5 cm and 24.0–25.5 cm, respectively. The intensive and semi-intensive treatments produced significantly more available forage for grazers annually than the extensive treatment. Forage yields in late May to early June were negatively correlated with spring bulk density.


2016 ◽  
Vol 36 (3) ◽  
pp. 449-459 ◽  
Author(s):  
Wininton M. da Silva ◽  
Aloísio Bianchini ◽  
Cesar A. da Cunha

ABSTRACT This study aimed to describe the behavior of models for adjusting data of soil penetration resistance for variations in soil moisture and soil bulk density. The study was carried out in Lucas do Rio Verde, MT, Brazil in a typic dystrophic red-yellow Latosol (Oxisol) containing 0.366 kg kg−1 of clay. Soil penetration resistance measurements were conducted in the soil moistures of 0.33 kg kg−1, 0.28 kg kg−1, 0.25 kg kg−1 and 0.22 kg kg−1. Soil penetration resistance behavior due to variations in soil moisture and soil bulk density was assessed by estimating the soil resistance values by non-linear models. There was an increase of the soil penetration resistance values as soil was losing moisture. For the same edaphic condition studied, small differences in the data of soil bulk density affect differently the response of soil resistance as a function of moisture. Both soil bulk density and soil moisture are essential attributes to explain the variations in soil penetration resistance in the field. The good representation of the critical soil bulk density curve as a limiting compression indicator requires the proper choice of the restrictive soil resistance value for each crop.


Bragantia ◽  
2014 ◽  
Vol 73 (2) ◽  
pp. 171-177 ◽  
Author(s):  
Daniel Dias Valadão Junior ◽  
Aloísio Biachini ◽  
Franciele Caroline Assis Valadão ◽  
Rodrigo Pengo Rosa

This study aimed to evaluate the effect of penetration rate and the size of the cone base on the resistance to penetration under different soil moistures and soil bulk density. The experimental design was completely randomized in a 4x2x2x2 factorial arrangement, with the factors, soil bulk density of 1.0; 1.2; 1.4 and 1.6 Mg m-3, soil moisture at the evaluation of 0.16 and 0.22 kg kg-1, penetration rates of 0.166 and 30 mm s-1 and areas of the cone base of 10.98 and 129.28 mm² resulting in 32 treatments with 8 replicates. To ensure greater uniformity and similarity to field conditions, samples passed through cycles of wetting and drying. Only the interaction of the four factors was not significant. Resistance values varied with the density of the soil, regardless of moisture and penetration rate. Soil penetration resistance was influenced by the size of the cone base, with higher values for the smallest base independent of moisture and soil bulk density. The relationship between resistance to penetration and moisture is not always linear, once it is influenced by soil bulk density. Reduction in the area of the cone leads to an increase in the soil resistance to penetration.


2015 ◽  
Vol 29 (4) ◽  
pp. 441-447 ◽  
Author(s):  
Michel Keisuke Sato ◽  
Herdjania Veras de Lima ◽  
Pedro Daniel de Oliveira ◽  
Sueli Rodrigues

Abstract The aim of this study was to evaluate the critical soil bulk density from the soil penetration resistance measurements for soybean root growth in Brazilian Amazon Oxisols. The experiment was carried out in a greenhouse using disturbed soil samples collected from the northwest of Para characterized by different texture. The treatments consisted of a range of soil bulk densities for each soil textural class. Three pots were used for soybean growth of and two for the soil penetration resistance curve. From the fitted model, the critical soil bulk density was determined considering the penetration resistance values of 2 and 3 MPa. After sixty days, plants were cut and root length, dry mass of root, and dry mass of shoots were determined. At higher bulk densities, the increase in soil water content decreased the penetration resistance, allowing unrestricted growth of soybean roots. Regardless of soil texture, the penetration resistance of 2 and 3 MPa had a slight effect on root growth in soil moisture at field capacity and a reduction of 50% in the soybean root growth was achieved at critical soil bulk density of 1.82, 1.75, 1.51, and 1.45 Mg m-3 for the sandy loam, sandy clay loam, clayey, and very clayey soil.


Agronomy ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 578
Author(s):  
Dariusz Błażejczak ◽  
Jan Jurga ◽  
Jarosław Pytka

The aim of this work was to develop a method of data grouping (DGM) that enables the selection of regression equations for forecasting soil penetration resistance based on an easily available and small set of input data: soil moisture content, soil bulk density and the grain size distribution of the soil. Models for forecasting the penetration resistance were created by selecting regression equations for specific intervals of granulometric variability of soil fractions. A field measurements campaign was conducted and soil samples were taken from the subsoil on 43 profiles, at depths of 25–30, 35–40, 45–50 and 55–60 cm. It was found that the dry bulk density is much less useful for predicting the penetration resistance of plastic soils than soil moisture. The study also showed that it is possible to forecast the soil penetration resistance on the basis of the gravimetric moisture content and the soil specific surface.


2015 ◽  
Vol 39 (3) ◽  
pp. 763-766
Author(s):  
Carolina Fernandes ◽  
Roniram Pereira da Silva ◽  
Adolfo Valente Marcelo

Soil quality indicators such as penetration resistance (PR) and bulk density (BD) are traditionally determined in a single undisturbed soil sample. The aim of this study was to assess the effect of PR measurements of undisturbed samples on the determination of BD in the same sample of two soils differing in clay contents. To this end, samples were collected from the 0.00-0.10 and 0.10-0.20 m layers of two soils of clayey and very clayey texture. Volumetric rings were used to collect a total of 120 undisturbed soil samples from each soil layer that were divided into two subsets containing 60 units each. One sample set, designated “perforated samples”, was used to determine PR and BD in the same undisturbed sample; the other, named “intact samples”, was used to determine BD only. Bulk density values for perforated and intact samples were compared by analysis of variance, using a completely randomized experimental design. Means were compared by the t-test at 5 %. The BD values for the clayey soil were similar in perforated and intact samples from the two layers. However, BD of the very clayey soil was lower in the perforated than in the intact samples at both depths. Therefore, PR and BD in clayey soils can be accurately determined in the same undisturbed sample whereas in very clayey soils, different samples are required for this purpose.


2018 ◽  
Vol 53 (4) ◽  
pp. 464-477 ◽  
Author(s):  
Moacir Tuzzin de Moraes ◽  
Renato Levien ◽  
Carlos Ricardo Trein ◽  
João de Andrade Bonetti ◽  
Henrique Debiasi

Abstract: The objective of this work was to determine whether compaction by tractor traffic in areas managed under controlled traffic can be limiting to corn crop, under different tillage systems, in a Typic Paleudult of medium texture. Two experiments were carried out, one in the field over two crop seasons and another in a greenhouse. The treatments consisted of minimum tillage with chiselling; no-tillage subjected to one, three, or six passes of a tractor weighing 3.8 Mg; and an area without traffic. Evaluations were performed for soil physico-hydraulic parameters (soil bulk density, penetration resistance, and water retention curve), root and shoot growth, and grain yield. The agricultural traffic increased bulk density, soil penetration resistance, and water content at field capacity. The highest values for soil penetration resistance (1,600 kPa) and bulk density (1.67 g cm-3) in the trafficked soil were not limiting to corn development and increased grain yield for both crop seasons. Tractor traffic of up to six passes is beneficial to corn cultivation, and it increases water availability and corn grain yield.


2019 ◽  
Vol 66 (2) ◽  
pp. 230-241
Author(s):  
Daniel DeArmond ◽  
João B S Ferraz ◽  
Fabiano Emmert ◽  
Adriano José Nogueira Lima ◽  
Niro Higuchi

Abstract In the forests of the Amazon Basin, there are still few studies on soil compaction caused by logging activities. This study evaluated an operation located on the property of a timber company in Central Amazonia, which uses harvesting techniques based on the harvesting system developed by the Centre for Agricultural Research in Suriname. The timber-extraction method employed by the timber company consists of three activities: (1) skid trail construction with a track-type tractor, (2) log winching with a winch attached to the tractor, and (3) log skidding with a rubber-tired skidder. Soil bulk density and soil penetration resistance were quantified to 20 cm in depth. After a single tractor ingress and egress for trail construction, the soil incurred an increased root growth-limiting bulk density and penetration resistance. However, log winching did not cause significant soil compaction. The conclusions of the study were: (1) the greatest impact from this harvesting system came from the skid trail construction, (2) the technique of log winching limited forest floor compaction and disturbance that damages forest regeneration, and (3) log skidding during dry soil conditions limited increases in compaction and track formation.


CERNE ◽  
2017 ◽  
Vol 23 (2) ◽  
pp. 193-200 ◽  
Author(s):  
Cristina Gouvêa Redin ◽  
Solon Jonas Longhi ◽  
José Miguel Reichert ◽  
Kelen Pureza Soares ◽  
Miriam Fernanda Rodrigues ◽  
...  

ABSTRACT Despite being prominent in flora, the region of the Parque Estadual do Espinilho located in the Pampas of southern Brazil, where dense herbaceous stratum and isolated trees make this region suitable for livestock farming, has received little attention. The objective of the study was to analyze floristic and edaphic changes imposed by livestock farming in two areas of the park, the first under livestock grazing and the second protected from grazing (livestock-excluded) for five years. We evaluated soil physical properties of and the herbaceous aboveground biomass in order to investigate relationships with key regenerating tree species. A sampling unit of 2ha was installed in both areas, each composed of 200 subunits. Inventory of regenerating trees and herbaceous aboveground biomass, soil sampling, and soil penetration resistance tests were done in 50 subunits. The results, which were evaluated by Student’s t-test, exhibited variations between the two areas in regards to floristic and environmental factors. The abundance of the P. affinis and V. caven species and the variables of soil penetration resistance, soil bulk density, gravimetric moisture and herbaceous aboveground biomass differ significantly between the two areas. Principal coordinates analysis (PCoA) allows to infer that variables such as soil bulk density, penetration resistance and the abundance of V. caven species exhibit higher values in the area under gazing, while gravimetric moisture, aboveground biomass and abundance of P. affinis are higher in the area under livestock-excluded, showing that significant changes occur over just five years of livestock-excluded from the area.


Sign in / Sign up

Export Citation Format

Share Document