scholarly journals Bond strength between fiber posts and composite resin core: influence of temperature on silane coupling agents

2012 ◽  
Vol 23 (1) ◽  
pp. 08-14 ◽  
Author(s):  
Veridiana Resende Novais ◽  
Paulo Cézar Simamotos Júnior ◽  
Regina Maria Puppin Rontani ◽  
Lourenço Correr-Sobrinho ◽  
Carlos José Soares
Keyword(s):  
Bond Strength ◽  
Coupling Agent ◽  
Silane Coupling Agent ◽  
Composite Resin ◽  
Coupling Agents ◽  
Silane Coupling Agents ◽  
Air Drying ◽  
Drying Temperature ◽  
Resin Core ◽  
Silane Coupling

This study evaluated the effect of air drying temperature and different silane coupling agents on the bond strength between glass fiber posts and composite resin core. The post surface was cleaned with alcohol and treated with different silane coupling agents, being three prehydrolyzed silanes [Silano (Angelus), Prosil (FGM), RelyX Ceramic Primer (3M ESPE)] and one two-component silane [Silane Coupling Agent (Dentsply)]. Two post-silanization air drying temperatures, 23ºC and 60ºC, were applied. A cylindrical plastic matrix was placed around the silanized post and filled with composite resin. Each bonded post provided 7 slices for push-out testing. Each slice was loaded to failure under compression at a cross-head speed of 0.5 mm/min. Data were analyzed by two-way ANOVA and Scott-Knott tests (α=0.05). Dunnett's test was used to compare the mean of the control group with that of each experimental group. Scanning electron microscopy (SEM) was used to evaluate the interface of the fractured slices. For the 23ºC air drying temperature, the use of RelyX Ceramic Primer resulted in significantly lower bond strength than the other silane coupling agents, while the bond strength with Silane Coupling Agent was the highest of all groups. Only with Silane Coupling Agent, the bond strength for the 23ºC air drying temperature was significantly higher than that for 60ºC air drying. In conclusion, the use of warm air drying after silane application produced no increase in the bond strength between the fiber-reinforced composite post and the composite core. The two-component silane produced higher bond strength than all prehydrolyzed silanes when it was used with air drying at room temperature.

scholarly journals Effect of Silane Type and Air-Drying Temperature on Bonding Fiber Post to Composite Core and Resin Cement

2014 ◽  
Vol 25 (3) ◽  
pp. 217-224 ◽  
Author(s):  
Camila Maria Peres de Rosatto ◽  
Marina Guimarães Roscoe ◽  
Veridiana Resende Novais ◽  
Murilo de Sousa Menezes ◽  
Carlos José Soares
Keyword(s):  
Bond Strength ◽  
Coupling Agent ◽  
Silane Coupling Agent ◽  
Room Temperature ◽  
Composite Resin ◽  
Resin Cement ◽  
Air Drying ◽  
Drying Temperature ◽  
Silane Coupling ◽  
Push Out

This study evaluated the influence of silane type and temperature of silane application on push-out bond strength between fiberglass posts with composite resin core and resin cement. One hundred and sixty fiberglass posts (Exacto, Angelus) had the surface treated with hydrogen peroxide 24%. Posts were divided in 8 groups according to two study factors: air-drying temperature after silane application (room temperature and 60 ºC) and silane type: three pre-hydrolyzed - Silano (Angelus), Prosil (FGM), RelyX Ceramic Primer (3M ESPE) and one two-component silane - Silane Coupling Agent (Dentsply). The posts (n=10) for testing the bond strength between post and composite core were centered on a cylindrical plastic matrix and composite resin (Filtek Z250 XT, 3M ESPE) that was incrementally inserted and photoactivated. Eighty bovine incisor roots (n=10) were prepared for testing the bond strength between post and resin cement (RelyX U100, 3M ESPE) and received the fiberglass posts. Push-out test was used to measure the bond strength. Data were analyzed by two-way ANOVA followed by Tukey's test (a=0.05). ANOVA revealed that temperature and silane had no influence on bond strength between composite core and post. However, for bond strength between post and resin cement, the temperature increase resulted in a better performance for Silane Coupling Agent, Silano and RelyX Ceramic Primer. At room temperature Silane Coupling Agent showed the lowest bond strength. Effect of the warm air-drying is dependent on the silane composition. In conclusion, the use of silane is influenced by wettability of resinous materials and pre-hydrolyzed silanes are more stable compared with the two-bottle silane.

scholarly journals Composite resin repairs: What is the most effective protocol?

2017 ◽  
Vol 20 (1) ◽  
pp. 99
Author(s):  
Alessandra Pereira Andrade ◽  
Angela Mayumi Shimaoka ◽  
Rubens Corte Real de Carvalho
Keyword(s):  
Bond Strength ◽  
Coupling Agent ◽  
Silane Coupling Agent ◽  
Composite Resin ◽  
Surface Treatments ◽  
Bonding Agent ◽  
Etch And Rinse ◽  
Silane Coupling ◽  
One Step ◽  
Self Etch

Objective: The objective of this study was to evaluate the combination effect of surface treatments and bonding agents on bond strength of repairs on aged composite resin. Materials and Methods: One hundred twenty microhybrid composite units (Filtek Z250) aged in distilled at 37ºC water for six months were submitted to different surface treatment prior to resin repairs. Ten specimens were randomly divided into 12 groups: non-treated/no bonding agent (negative control), sandblasting /no bonding agent, silane/no bonding agent, non-treated/ etch-and-rinse; non-treated/one-step self-etch; non-treated/ two-step self-etch; sandblasting/etch-and-rinse; sandblasting/one-step self-etch; sandblasting/two-step self-etch; silane coupling agent/etch-and-rinse; silane coupling agent/ one-step self-etch; silane coupling agent/two-step self-etch. Microshear testing was performed to bond strength assessment. Results: Two-way ANOVA and Tukey’s test (α=0.05) demonstrated significant difference between the surface treatments and adhesive systems. Only no treated surface/etch-and-rinse group showed lower bond strength values when compared to other groups. Conclusion: The considered surface treatments were capable to increase the effectiveness of the repair in composite resin when using the adhesive etch-and-rinse.

Surface Functionalization of Zirconia Nanocrystals with Silane Coupling Agent and its Dispersion Behavior in O-Phenylphenoxyethyl Acrylate

2018 ◽  
Vol 922 ◽  
pp. 20-25 ◽  
Author(s):  
Hee Seon Lee ◽  
Jeong Min Park ◽  
Kyu Hong Hwang ◽  
Hyung Mi Lim
Keyword(s):  
Coupling Agent ◽  
Silane Coupling Agent ◽  
Coupling Agents ◽  
Solvothermal Reaction ◽  
Silane Coupling Agents ◽  
Propyl Methacrylate ◽  
Silane Coupling ◽  
Ft Ir ◽  
Surface Modified ◽  
Dispersion Of Nanoparticles

Highly crystalline and dispersible zirconia, synthesized by solvothermal reaction of zirconium (IV) isopropoxide isopropanol complex in benzyl alcohol, were functionalized with silane coupling agent and dispersed with o-phenylphenoxyethyl acrylate (OPPEA). Silane coupling agents such as 3-aminopropyltriethoxysilane (APTES) of amino functional silane, decyltrimethoxysilane (DTMS) of alkyl functional silane and 3-(trimethoxysilyl) propyl methacrylate (MPS) of acrylate functional silane have been used to modify nanoparticle surfaces and obtain dispersion of nanoparticles within OPPEA. The surface modified zirconia was compared according to silane coupling agent, FT-IR and TGA demonstrated that APTES, DMTS and MPS are chemically attached to the surface of the zirconia. The MPS-zirconia is dispersed as about 5 nm sized, whereas the APTES-zirconia, DTMS-zirconia are agglomerated. The MPS-zirconia/tetrahydrofuran (THF) sol at 15wt% loading shows high transmittance of 68 % at 550 cm-1 and the 50wt% surface modified-zirconia/OPPEA sol show refractive index of 1.657.

scholarly journals Acid Etching and Surface Coating of Glass-Fiber Posts: Bond Strength and Interface Analysis

2016 ◽  
Vol 27 (2) ◽  
pp. 228-233 ◽  
Author(s):  
Doglas Cecchin ◽  
Ana Paula Farina ◽  
Rafael Pino Vitti ◽  
Rafael Ratto Moraes ◽  
Ataís Bacchi ◽  
...  
Keyword(s):  
Phosphoric Acid ◽  
Bond Strength ◽  
Glass Fiber ◽  
Coupling Agent ◽  
Surface Coating ◽  
Silane Coupling Agent ◽  
Failure Modes ◽  
Composite Resin ◽  
Silane Coupling ◽  
Unfilled Resin

Abstract The aim of this study was to evaluate the bond strength of a composite resin to glass-fiber post (GFP) treated or not with phosphoric acid, silane coupling agent, and unfilled resin. GFPs were etched or not with 37% phosphoric acid and different surface coating applied: silane coupling agent, unfilled resin, or both. Composite resin blocks were built around a 4-mm height on the GFP. Unfilled resin (20 s) and composite resin (40 s) were light activated by a light-emitting diode unit. The specimens were stored in distilled water at 37 °C for 24 h. Microtensile bond test was performed using a mechanical testing machine until failure (n=10). The data were analyzed using two-way ANOVA followed by Student-Newman-Keuls' test (p<0.05). Failure modes were classified as adhesive, mixed, or cohesive failures. Additional specimens (n=3) were made to analyze the bonded interfaces by scanning electron microscopy. The statistical analysis showed the factor 'surface coating' was significant (p<0.05), whereas the factor 'HP etching' (p=0.131) and interaction between the factors (p=0.171) were not significant. The highest bond strength was found for the silane and unfilled resin group (p<0.05). A predominance of adhesive and cohesive failures was found. Differences regarding the homogeneity and thickness of the unfilled resin layer formed by different GFP surface treatments were observed. The application of silane and unfilled resin can improve the bond strength between GFP and resin composite.

scholarly journals Effect of Silane Coupling Agent on Modification of Areca Fiber/Natural Latex

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 4896
Author(s):  
Yiren Pan ◽  
Meng Zhang ◽  
Jian Zhang ◽  
Xiaoyao Zhu ◽  
Huiguang Bian ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Coupling Agent ◽  
Silane Coupling Agent ◽  
Natural Rubber Latex ◽  
Physical And Mechanical Properties ◽  
Coupling Agents ◽  
Silane Coupling Agents ◽  
Swelling Properties ◽  
Silane Coupling ◽  
Physical And Chemical

In this paper, the areca fiber was extracted by physical and chemical treatment, and then the areca fiber/natural latex composite was prepared by natural latex impregnation technology. In order to combine areca fiber and natural rubber latex better, three silane coupling agents with different action mechanism were selected: Si−69, KH550, and KH570 which were used to treat the areca fiber/natural latex compound. The results show that the silane coupling agent can change the surface of the fiber from hydrophilic surface to organophilic surface, making the bonding of areca fiber to natural latex more closely. At the same time, the mechanical properties, physical and mechanical properties, swelling properties, and dynamic viscoelastic properties of the tightly bonded areca fiber/nature latex composites were improved. After observing the micro-structure through a scanning electron microscope, it was found that the three silane coupling agents could effectively bind areca fiber and natural latex to enhance the performance of the composite material, of which Si−69 performed best, and the tensile strength and tear strength of the composite increased by 21.19% and 12.90% respectively.

scholarly journals Treatment of hollow glass bubbles with silane coupling agent. sem on hollow glass bubbles, before and after treatment with silane coupling agent

2021 ◽  
Vol 2 (2) ◽  
pp. 1-7
Author(s):  
Andrei-Ionut Perdum
Keyword(s):  
Coupling Agent ◽  
Silane Coupling Agent ◽  
Hollow Spheres ◽  
Coupling Agents ◽  
Silane Coupling Agents ◽  
Hollow Glass ◽  
Glass Spheres ◽  
Silane Coupling ◽  
Before And After ◽  
Glass Bubble

In this study will be presented, how 20 millilitres of Silane Coupling Agent, adhered on 5 grams of Hollow Glass Bubbles (HGB), how the micro bubbles are looking before and after mixing, how to filter the hollow spheres from the agent and what needed to be taken in consideration when using coupling agents in processes. This paper will show how Silane Coupling Agent (3-Aminopropyl) triethoxysilane, adhered on the Hollow Glass Bubble (HGB). It is expected to observe at HR-SEM (High- Resolution Scanning Electron Microscopy) how the Hollow Glass Bubbles looks when the Silane Coupling Agent (KH-550) is applied on the filler vs when is not. During the process will be concluded, what risks should be taken in consideration, when using Silane Coupling Agents on Hollow Glass Spheres and what important information/ steps are needed to be taken in consideration before and after coupling treatment.

scholarly journals The Investigation of the Silica-Reinforced Rubber Polymers with the Methoxy Type Silane Coupling Agents

Polymers ◽  
2020 ◽  
Vol 12 (12) ◽  
pp. 3058
Author(s):  
Sang Yoon Lee ◽  
Jung Soo Kim ◽  
Seung Ho Lim ◽  
Seong Hyun Jang ◽  
Dong Hyun Kim ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Coupling Agent ◽  
Silane Coupling Agent ◽  
Testing Machine ◽  
Styrene Butadiene Rubber ◽  
Coupling Agents ◽  
Butadiene Rubber ◽  
Silane Coupling Agents ◽  
Rubber Composites ◽  
Silane Coupling

The methoxy-type silane coupling agents were synthesized via the modification of the hydrolyzable group and characterized to investigate the change in properties of silica/rubber composites based on the different silane coupling agent structures and the masterbatch fabrication methods. The prepared methoxy-type silane coupling agents exhibited higher reactivity towards hydrolysis compared to the conventional ethoxy-type one which led to the superior silanization to the silica filler surface modified for the reinforcement of styrene-butadiene rubber. The silica/rubber composites based on these methoxy-type silane coupling agents had the characteristics of more developed vulcanization and mechanical properties when fabricated as masterbatch products for tread materials of automobile tire surfaces. In particular, the dimethoxy-type silane coupling agent showed more enhanced rubber composite properties than the trimethoxy-type one, and the environmentally friendly wet masterbatch fabrication process was successfully optimized. The reactivity of the synthesized silane coupling agents toward hydrolysis was investigated by FITR spectroscopic analysis, and the mechanical properties of the prepared silica-reinforced rubber polymers were characterized using a moving die rheometer and a universal testing machine.

scholarly journals Synergistic effects of zwitterionic segments and a silane coupling agent on zwitterionic shape memory polyurethanes

RSC Advances ◽  
2017 ◽  
Vol 7 (67) ◽  
pp. 42320-42328 ◽  
Author(s):  
Zaochuan Ge ◽  
Huanhuan Ren ◽  
Shuqin Fu ◽  
Shaojun Chen
Keyword(s):  
Shape Memory ◽  
Coupling Agent ◽  
Silane Coupling Agent ◽  
Synergistic Effects ◽  
Coupling Agents ◽  
Silane Coupling Agents ◽  
Structure Morphology ◽  
Silane Coupling ◽  
Shape Memory Properties ◽  
Novel Strategy

A novel strategy to improve shape memory properties of ZSMPUs by using a silane coupling agent. The synergistic effects of zwitterionic segments and silane coupling agents on the structure, morphology, properties were carefully investigated.

Sign in / Sign up

Export Citation Format

Share Document