scholarly journals The novel design of an energy efficient superconductor-based series reactor for installation at a grid connected research site

2020 ◽  
Vol 31 (2) ◽  
pp. 19-33
Author(s):  
Mohamed F. Khan ◽  
A.L. Leigh Jarvis ◽  
Edward A. Young ◽  
Andrew G. Swanson ◽  
Jonathan C. Archer ◽  
...  
Keyword(s):  
Power System ◽  
Energy Efficient ◽  
Power Loss ◽  
Power Efficiency ◽  
Simulation Software ◽  
Calorimetric Method ◽  
Design Parameters ◽  
Fault Current ◽  
Research Site ◽  
Loss Determination

This paper proposes the development of a superconducting series reactor (SSR) as an alternative to traditionally employed technologies and superconducting fault current limiters when managing fault levels on the electrical power grid. By utilizing superconducting tape, which has negligible resistance, in the construction of a series reactor, it is proposed that fault level mitigation could be achieved in a more energy efficient manner. Once constructed the SSR will be installed and tested at a grid-connected power engineering research site, and the proposed impact of this installation is firstly simulated using Reticmaster® power system simulation software. Design parameters for the prototype SSR are then calculated enabling the total cost of the modifications and prototype SSR to be determined. A desktop SSR was also constructed and tested as a pre-cursor to the prototype construction to confirm functionality and design and was found to be up to four times more energy efficient as the equivalent copper reactor. Finally, the calorimetric method of power loss determination was investigated and experimentally shown to be a viable alternative to the traditional electrical method of power loss determination. In the past, the relatively cheap cost of electricity in South Africa had favoured the installation of poor power efficiency devices that required a lower initial capital investment. With increasing energy costs and a focus on carbon emission reductions, the development of the SSR augurs a new era in power system engineering in which designs are proposed considering both total lifecycle costs and energy efficiency. Design proposal for the first superconducting power device in Africa Alternative to less efficient fault current management technologies currently employed Construction and testing of a desktop superconducting series reactor Verification of the calorimetric method for power loss determination.

TRIPLEPR-MAC: A Triple Queue Priority Based Medium Access Control Protocol for Wireless Sensor Network

2019 ◽  
Vol 09 ◽  
Author(s):  
Rinkuben N. Patel ◽  
Nirav V. Bhatt
Keyword(s):  
Sensor Network ◽  
Data Transmission ◽  
Energy Efficient ◽  
Power Efficiency ◽  
Mac Protocol ◽  
Medium Access Control Protocol ◽  
Quality Factors ◽  
Medium Access ◽  
Critical Fields ◽  
Storage Unit

Background: WSN is a network of smart tiny electromechanical devices named as sensors. Sensors perform various tasks like sensing the environment as per its range, transmit the data using transmission units, store the data in the storage unit and perform an action based on captured data. As they are installed in an unfriendly environment, to recharge the sensors are not possible every time which leads to a limited lifetime of a network. To enhance the life of a sensor network, the network required energy-efficient protocols. Various energy-efficient MAC protocols are developed by Research community, but very few of them are integrated with the priority-based environment which performs the priority-based data transmission. Another challenge of WSN is, most of the WSN areas are delay-sensitive because it is implemented in critical fields like military, disaster management, and health monitoring. Energy, Delay, and throughput are major quality factors that affect the sensor network. Objective: In this paper, the aim is to design and develop a MAC Protocol for a field like the military where the system requires energy efficiency and priority-based data transmission. Method: In the proposed model, the cluster-based network with priority queues are formed that can achieve higher power efficiency and less delay for sensitive data. Results: In this research simulation of Proposed MAC, TMAC and SMAC are done with different numbers of nodes, same inter-packet intervals, and variant inter-packet intervals. Based on the script simulation, result graphs are generated. Conclusion: The proposed work achieves greater lifetime compared to TMAC and SMAC using priority-based data transmission.

scholarly journals Solid-State DC Circuit Breakers and their Comparison in Modular Multilevel Converter Based-HVDC Transmission System

Electronics ◽  
2021 ◽  
Vol 10 (10) ◽  
pp. 1204
Author(s):  
Gul Ahmad Ludin ◽  
Mohammad Amin Amin ◽  
Hidehito Matayoshi ◽  
Shriram S. Rangarajan ◽  
Ashraf M. Hemeida ◽  
...  
Keyword(s):  
Solid State ◽  
High Voltage ◽  
Direct Current ◽  
Circuit Breaker ◽  
Transmission System ◽  
Simulation Software ◽  
Fault Current ◽  
Circuit Breakers ◽  
Hvdc Transmission ◽  
Dc Circuit Breakers

This paper proposes a new and surge-less solid-state direct current (DC) circuit breaker in a high-voltage direct current (HVDC) transmission system to clear the short-circuit fault. The main purpose is the fast interruption and surge-voltage and over-current suppression capability analysis of the breaker during the fault. The breaker is equipped with series insulated-gate bipolar transistor (IGBT) switches to mitigate the stress of high voltage on the switches. Instead of conventional metal oxide varistor (MOV), the resistance–capacitance freewheeling diodes branch is used to bypass the high fault current and repress the over-voltage across the circuit breaker. The topology and different operation modes of the proposed breaker are discussed. In addition, to verify the effectiveness of the proposed circuit breaker, it is compared with two other types of surge-less solid-state DC circuit breakers in terms of surge-voltage and over-current suppression. For this purpose, MATLAB Simulink simulation software is used. The system is designed for the transmission of 20 MW power over a 120 km distance where the voltage of the transmission line is 220 kV. The results show that the fault current is interrupted in a very short time and the surge-voltage and over-current across the proposed breaker are considerably reduced compared to other topologies.

Influence of a Flux-Coupling Type Superconducting Fault Current Limiter on Power System Transient Stability

2012 ◽  
Vol 588-589 ◽  
pp. 632-637
Author(s):  
Ge Fei Qiu ◽  
Jun Hao Cao ◽  
Zi Qing Xu ◽  
Meng Song ◽  
Lei Chen ◽  
...  
Keyword(s):  
Power System ◽  
Transient Stability ◽  
Fault Current ◽  
Fault Current Limiter ◽  
Stability Calculation ◽  
Superconducting Fault Current Limiter ◽  
Flux Coupling ◽  
Calculation Results ◽  
Current Limiter ◽  
Coupling Type

In this paper, the influence of superconducting fault current limiter (SFCL, flux-coupling type) on power system transient stability is studied in detail. The influence of SFCL to transient stability of power system is studied using a model of single generator infinite bus system, different transient stability calculation results gotten with and without SFCL and with model system in different fault conditions are compared. The results show that the SFCL can effectively reduce the transient swing amplitude of rotor and extend the critical clearance time, and the application of SFCL in the power system can help to enhance its transient stability.

scholarly journals An Improved Particle Swarm Optimization Algorithm Using Eagle Strategy for Power Loss Minimization

2017 ◽  
Vol 2017 ◽  
pp. 1-11 ◽  
Author(s):  
Hamza Yapıcı ◽  
Nurettin Çetinkaya
Keyword(s):  
Genetic Algorithm ◽  
Particle Swarm Optimization ◽  
Power System ◽  
Power Loss ◽  
Particle Swarm Optimization Algorithm ◽  
Reactive Power ◽  
Particle Swarm ◽  
Power Losses ◽  
Swarm Optimization ◽  
Eagle Strategy

The power loss in electrical power systems is an important issue. Many techniques are used to reduce active power losses in a power system where the controlling of reactive power is one of the methods for decreasing the losses in any power system. In this paper, an improved particle swarm optimization algorithm using eagle strategy (ESPSO) is proposed for solving reactive power optimization problem to minimize the power losses. All simulations and numerical analysis have been performed on IEEE 30-bus power system, IEEE 118-bus power system, and a real power distribution subsystem. Moreover, the proposed method is tested on some benchmark functions. Results obtained in this study are compared with commonly used algorithms: particle swarm optimization (PSO) algorithm, genetic algorithm (GA), artificial bee colony (ABC) algorithm, firefly algorithm (FA), differential evolution (DE), and hybrid genetic algorithm with particle swarm optimization (hGAPSO). Results obtained in all simulations and analysis show that the proposed method is superior and more effective compared to the other methods.

scholarly journals Combined Vapor Permeation and Continuous Solid-State Distillation for Energy-Efficient Bioethanol Production

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2266
Author(s):  
Hongshen Li ◽  
Hongrui Liu ◽  
Yufang Li ◽  
Jilin Nan ◽  
Chen Shi ◽  
...  
Keyword(s):  
Solid State ◽  
Energy Efficient ◽  
Simulation Software ◽  
Separation Performance ◽  
Flow Sheet ◽  
Bioethanol Production ◽  
Permeate Flux ◽  
Rectification Column ◽  
Vapor Permeation ◽  
Wide Range

Extracting ethanol by steam directly from fermented solid-state bagasse is an emerging technology of energy-efficient bioethanol production. With continuous solid-state distillation (CSSD) approach, the vapor with more than 25 wt% ethanol flows out of the column. Conventionally, the vapor was concentrated to azeotrope by rectification column, which contributes most of the energy consumption in ethanol production. As an alternative, a process integrating CSSD and vapor permeation (VP) membrane separation was tested. In light of existing industrial application of NaA zeolite hydrophilic membrane for dehydration, the prospect of replacing rectification operation with hydrophobic membrane for ethanol enriching was mainly analyzed in this paper. The separation performance of a commercial PDMS/PVDF membrane in a wide range of ethanol–water-vapor binary mixture was evaluated in the experiment. The correlation of the separation factor and permeate flux at different transmembrane driving force was measured. The mass and energy flow sheet of proposed VP case and rectification case were estimated respectively with process simulation software based on experimental data. Techno-economic analysis on both cases was performed. The results demonstrated that the additional VP membrane cost was higher than the rectification column, but a lower utilities cost was required for VP. The discount payback period of supplementary cost for VP case was determined as 1.81 years compared with the membrane service lifetime of 3 years, indicating that the hybrid CSSD-VP process was more cost effective and energy efficient.

ENHANCING THERMAL COMFORT OF RESIDENTIAL BUILDINGS THROUGH A DUAL FUNCTIONAL PASSIVE SYSTEM (SOLAR-WALL)

2021 ◽  
Vol 16 (3) ◽  
pp. 155-177
Author(s):  
Shouib Mabdeh ◽  
Tamer Al Radaideh ◽  
Montaser Hiyari
Keyword(s):  
Thermal Comfort ◽  
Residential Buildings ◽  
Simulation Software ◽  
Design Parameters ◽  
Base Case ◽  
Passive System ◽  
Efficient System ◽  
Dual Functional ◽  
Solar Wall ◽  
New System

ABSTRACT Thermal comfort has a great impact on occupants’ productivity and general well-being. Since people spend 80–90% of their time indoors, developing the tools and methods that enhance the thermal comfort for building are worth investigating. Previous studies have proved that using passive systems like Trombe walls and solar chimneys significantly enhanced thermal comfort in inside spaces despite that each system has a specific purpose within a specific climate condition. Hence, the main purpose of this study is to design and configure a new, dual functional passive system, called a solar wall. The new system combines the Trombe wall and solar chimney, and it can cool or heat based on building needs. Simulation software, DesignBuilder, has been used to configure the Solar Wall, and study its impact on indoor operative temperature for the base case. Using the new system, the simulation results were compared with those obtained in the base case and analyzed to determine the most efficient system design parameters and implementation method. The case that gave the best results for solar wall configuration was triple glazed glass and 0.1 cm copper as an absorber (case 11). The results show that using four units (case D) achieves longer thermal comfort levels: 15 to 24 thermal hours during winter (compared to five hours maximum) and 10 to 19 comfort hours in summer (compared to zero).

ENHANCING THERMAL COMFORT OF RESIDENTIAL BUILDINGS THROUGH DUAL FUNCTIONAL PASSIVE SYSTEM (SOLAR-WALL)

2021 ◽  
Vol 16 (1) ◽  
pp. 139-161
Author(s):  
Shouib Mabdeh ◽  
Tamer Al Radaideh ◽  
Montaser Hiyari
Keyword(s):  
Thermal Comfort ◽  
Residential Buildings ◽  
Simulation Software ◽  
Design Parameters ◽  
Base Case ◽  
Passive System ◽  
Efficient System ◽  
Dual Functional ◽  
Solar Wall ◽  
New System

ABSTRACT Thermal comfort has a great effect on occupants’ productivity and general well-being. Since people spend 80–90% of their time indoors, developing the tools and methods that help in enhancing the thermal comfort for buildings are worth investigating. Previous studies have proved that using passive systems like Trombe walls and solar chimneys significantly enhanced thermal comfort in inside spaces despite that each system has a specific purpose within a specific climate condition. Hence, the main purpose of this study is to design and configure a new dual functional passive system, called a solar wall. The new system combines the Trombe wall and solar chimney, and it can cool or heat based on building needs. Simulation software, DesignBuilder, has been used to configure the Solar Wall and study its impact on indoor operative temperature for the base case. Using the new system, the simulation results were compared with those obtained in the base case and analyzed to determine the most efficient system design parameters and implementation method. The case that gave the best results for solar wall configuration was triple glazed glass and 0.1 cm copper as an absorber (case 11). The results show that using four units (case D) achieves longer thermal comfort levels: 15 to 24 thermal hours during winter (compared to five hours maximum) and 10 to 19 comfort hours in summer (compared to zero).

Sign in / Sign up

Export Citation Format

Share Document