On the issue of selecting and optimizing parameters of continuous laser welding of cast iron

2021 ◽  
Vol 23 (3) ◽  
pp. 20-30
Author(s):  
Dmitry Ilyushkin ◽  
◽  
Valery Soldatov ◽  
Oleg Petrakov ◽  
Irina Kotlyarova ◽  
...  
Keyword(s):  
Cast Iron ◽  
Laser Welding ◽  
Weld Pool ◽  
Process Parameters ◽  
Welding Speed ◽  
Optimization Problem ◽  
Radiation Power ◽  
Geometric Parameters ◽  
Continuous Laser ◽  
Passive Experiment

Introduction. Cast iron extremely poorly tolerate thermal welding cycles, and therefore it is necessary to choose carefully the technological parameters. The main parameters of continuous laser welding are: the power of laser radiation, the welding speed, the parameters of the focusing system. The aim of the work is to determine the optimal power and speed of continuous laser welding of cast iron, depending on the geometry of the weld. In this paper, the welding seams obtained on samples of gray alloyed cast iron with a pearlitic metal base, using an LS-1 ytterbium fiber laser, are studied. Research methods. The geometric parameters of the joints were quantified in the program for quantitative analysis and image processing ImageJ. The obtained data were processed by regression analysis. To optimize the process parameters, an orthogonal plan of the passive experiment was developed, including nine experiments in which the factors varied at three equally spaced levels. The quality parameters in the passive experiment were the geometric dimensions of the weld pool and the size of the quenched zone. To solve the optimization problem, we used the methods of gray relational analysis and linear programming. Results and Discussions. The obtained regression models explain a significant proportion of the variance of the dependent variables, the regression coefficients, as well as the models themselves, are statistically significant, which indicates a close linear relationship between the seam geometry and the process parameters. The calculated shape of the weld pool depending on the radiation power and welding speed shows that the required welding seam of the required dimensions can be obtained at various process parameters which allow solving a multi-criteria optimization problem. The gray relational evaluation of the geometric parameters of the seam shows that the most correct parameters in terms of obtaining the seam of the maximum depth with the minimum width, convexity (concavity) and the quenched zone are the minimum power and maximum welding speed. The calculation of the optimal radiation power and welding speed depending on the seam depth showed that welding of small thicknesses is optimally carried out with minimal power, and the seam depth is adjusted by changing the beam speed. Welding of large thicknesses is optimal at high speed, and to increase the depth of the seam, the power must increase.

Characterization of Fusion Lines Obtained with Laser Welding on Ductile Iron Plates

2016 ◽  
Vol 254 ◽  
pp. 33-42
Author(s):  
Ioan Catalin Mon ◽  
Mircea Horia Tierean ◽  
Eugen Cicala ◽  
Michel Pilloz ◽  
Iryna Tomashchuk ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Laser Welding ◽  
Welding Speed ◽  
Ductile Iron ◽  
Continuous Laser ◽  
Welding Defects ◽  
Criteria For Selection ◽  
Selection Of ◽  
Melted Metal

This paper studies the ductile iron (DI) weldability using laser welding. For performing an Yb:YAG continuous laser was used, with a maximum power of 6 kW. The parametrical window power (P) - welding speed (S) was explored by carrying out the fusion lines on ductile iron plates without preheating, to determinate areas of weldability (complete penetration, correct geometry) to allow further characterization. The criteria for selection of focus areas were the geometry of the fusion lines and the absence of the welding defects. The unsatisfactory domains were characterized by: collapse of the melted metal, incomplete penetration, low fusion lines quality (geometry, compactness). In present study, several values of power and welding speed have been tested to identify their influence on geometry, compactness of the joints and mechanical properties. As result, the power-welding speed diagram for feasible domains of laser welding was generated.

Numerical Analysis of Solidification Behavior during Laser Welding Nickel-Based Single-Crystal Superalloy Part: II Crystallography-Dependent Supersaturation of Liquid Aluminum

2021 ◽  
Vol 1018 ◽  
pp. 13-22
Author(s):  
Zhi Guo Gao
Keyword(s):  
Laser Welding ◽  
Single Crystal ◽  
Weld Pool ◽  
Welding Speed ◽  
Heat Input ◽  
Laser Power ◽  
Liquid Aluminum ◽  
Dendrite Growth ◽  
Solidification Cracking ◽  
Solid Liquid Interface

The thermal metallurgical modeling of liquid aluminum supersaturation was further developed through couple of heat transfer model, dendrite selection model, multicomponent dendrite growth model and nonequilibrium solidification model during three-dimensional nickel-based single-crystal superalloy weld pool solidification. The welding configuration plays more important role in supersaturation of liquid aluminum, morphology instability and nonequilibrium partition behavior. The bimodal distribution of liquid aluminum supersaturation along the solid/liquid interface is crystallographically symmetrical about the weld pool centerline in (001) and [100] welding configuration. The distribution of liquid aluminum supersaturation along the solid/liquid interface is crystallographically asymmetrical throughout the weld pool in (001) and [110] welding configuration. Optimum low heat input (low laser power and high welding speed) with (001) and [100] welding configuration is more favored to predominantly promote epitaxial [001] dendrite growth to reduce the metallurgical factors for solidification cracking than that of high heat input (high laser power and slow welding speed) with (001) and [110] welding configuration. The lower the heat input is used, the lower supersaturation of liquid aluminum is imposed, and the smaller size of vulnerable [100] dendrite growth region is incurred to ameliorate solidification cracking susceptibility and vice versa. The overall supersaturation of liquid aluminum in (001) and [100] welding configuration is beneficially smaller than that of (001) and [110] welding configuration regardless of heat input, and is not thermodynamically relieved by gamma prime γˊ phase. (001) and [110] welding configuration is detrimental to weldability and deteriorates the solidification cracking susceptibility because of unfavorable crystallographic orientations and alloying aluminum enrichment. The mechanism of asymmetrical solidification cracking because of crystallography-dependent supersaturation of liquid aluminum is proposed. The eligible solidification cracking location is particularly confined in [100] dendrite growth region. Moreover, the theoretical predictions agree well with the experiment results. The useful modeling is also applicable to other single-crystal superalloys with similar metallurgical properties for laser welding or laser cladding. The thorough numerical analyses facilitate the understanding of weld pool solidification behavior, microstructure development and solidification cracking phenomena in the primary γ phase, and thereby optimize the welding conditions (laser power, welding speed and welding configuration) for successful crack-free laser welding.

Modeling of Weld Lap-Shear Strength for Laser Transmission Welding of Thermoplastic Using Artificial Neural Network

2012 ◽  
Vol 445 ◽  
pp. 454-459 ◽  
Author(s):  
M.R. Nakhaei ◽  
N.B. Mostafa Arab ◽  
F. Kordestani
Keyword(s):  
Neural Network ◽  
Artificial Neural Network ◽  
Shear Strength ◽  
Laser Welding ◽  
Process Parameters ◽  
Welding Speed ◽  
Laser Power ◽  
Laser Transmission Welding ◽  
Lap Shear Strength ◽  
Lap Shear

Laser welding of plastic materials has a wide range of applications in the packaging, medical, electronics and automobile industries provided it can predict high quality welds compared with other joining methods. Laser welding process parameters can affect the quality of welds. In this paper, Artificial Neural Network (ANN) is used to model the effects of laser power, welding speed, clamp pressure and stand-off distance on weld lap-shear strength in laser transmission welding (LTW) of acrylic (polymathy methacrylate). A set of experimental data on diode laser weld lap-shear strengths was used to train and test the ANN from which the neurons relations were gradually extracted to develop a model. The developed ANN model can be used for the analysis and prediction of the complex relationships between the above mentioned process parameters and weld lap-shear strength. The results indicated that increase in laser power and clamp pressure increases the weld lap-shear strength whereas welding speed and stand off distance had a decreasing affect on shear strength at high value.

A study of laser welding modes with varying beam energy levels

2008 ◽  
Vol 223 (5) ◽  
pp. 1141-1156 ◽  
Author(s):  
G Buvanashekaran ◽  
Siva N Shanmugam ◽  
K Sankaranarayanasamy ◽  
R Sabarikanth
Keyword(s):  
Finite Element ◽  
Stainless Steel ◽  
Laser Welding ◽  
Weld Pool ◽  
Welding Speed ◽  
Laser Power ◽  
Beam Energy ◽  
Energy Levels ◽  
Three Dimensional ◽  
Laser Source

The energy of a laser beam is generally calculated based on the laser power and its processing speed. In this work, the laser welding modes such as conduction, conduction—penetration, and keyhole welding of thickness 1.6, 2, and 2.5 mm AISI304 stainless steel sheets, respectively, are studied at different beam energy levels. A series of bead-on-plate trials are conducted using a 500 W continuous wave Nd:YAG laser source to study the beam—material interaction and the influence of laser power and welding speed on the formation of weld pool. In addition to the experimental study, a three-dimensional finite-element model is developed to analyse the transient heat flow and to predict the formation of the weld pool. The correlation among the parameters including laser power, welding speed, beam incident angle, and the characteristic geometry of weld pool are established. Temperature-dependent thermal properties of AISI304 stainless steel, the effect of latent heat of fusion, and the convective and radiative aspects of boundary conditions are considered in the model. The heat input to the developed model is assumed to be a three-dimensional conical Gaussian heat source. Finite-element simulations are carried out by using finite-element code, SYSWELD, and FORTRAN subroutines available within the code are used to obtain the numerical results. The result of the numerical analysis provides the shape of the molten pool with different beam energy levels, which is then compared with the results obtained through experimentation. It is observed that the results obtained from finite-element simulation and the experimental trials are in good agreement.

Dual Process Welding of Steel Plate

2002 ◽  
Author(s):  
Clint Wildash ◽  
Steve Webster
Keyword(s):  
Laser Welding ◽  
Weld Pool ◽  
Welding Speed ◽  
Welded Joint ◽  
Laser Beam Welding ◽  
Dual Process ◽  
Dual Processing ◽  
Laser Weld ◽  
Stage 1 ◽  
Welding Processes

Large scale fabrication and welding industries, such as those involved in offshore construction, are continuously striving to improve productivity, while maintaining quality levels required by the applicable design codes and standards. To achieve this, new improved welding technologies are regularly being evaluated. One area of development is to combine different welding processes to produce a welded joint exhibiting properties and productivity benefits that neither process could achieve individually. One promising combination is the use of both arc and laser beam welding for products such as pipeline. The welding procedure development work described, was carried out in two stages. Stage 1 (discrete dual processing) investigated the production of a welded joint using both arc and laser welding at separate times. The welds produced for this work, demonstrate that significant increases in welding speed are achievable in comparison to using either process individually. Stage 2 (simultaneous dual processing) investigated arc and laser welding of the joint at the same time from opposing plate faces, with the laser weld pool trailing the arc weld pool so that the former was positioned in the area of highest preheat temperature. The use of arc preheat significantly reduced the hardness of the laser welds to more acceptable levels. The main disadvantage identified for both stages of work was that fit up of the laser welded part of the joint needed to be good to accommodate the autogenous laser weld. Both Stages were shown to be capable of producing full penetration welds at higher productivity than using either process individually. It has been demonstrated that for 19 mm thick plate, an overall doubling of welding speed could be achieved using dual process as opposed to submerged arc welding, which is currently widely used to weld fabricated products such as pipeline. Future work to be carried will include extensive destructive testing on the welds to assess the benefits of Stage 1 and 2, which will be reported in another paper.

scholarly journals Features of the process of laser welding of cast iron with steel

2021 ◽  
Vol 1870 (1) ◽  
pp. 012020
Author(s):  
V V Zvezdin ◽  
R R Rakhimov ◽  
R M Khisamutdinov ◽  
S M Portnov ◽  
R R Saubanov
Keyword(s):  
Cast Iron ◽  
Laser Welding

Procedure to find out the optimal ranges of process parameters for friction stir welding

2021 ◽  
pp. 146442072199314
Author(s):  
Shubham Verma ◽  
Joy Prakash Misra ◽  
Meenu Gupta
Keyword(s):  
Friction Stir Welding ◽  
Process Parameters ◽  
Tilt Angle ◽  
Welding Speed ◽  
Rotational Speed ◽  
Optical Microscope ◽  
Graphical Analysis ◽  
Friction Stir ◽  
Steepest Ascent ◽  
Vertical Milling Machine

The present study deals with the application of sequential procedure (i.e. steepest ascent) to obtain the optimum values of process parameters for conducting friction stir welding (FSW) experiments. A vertical milling machine is modified by fabricating fixture and tool ( H13 material) for performing FSW operation to join AA7039 plates. The steepest ascent technique is employed to design the experiments at different rotational speed, welding speed, and tilt angle. The ultimate tensile strength is considered as a performance characteristic for deciding the optimal levels. The mechanical and metallurgical characteristics of the joints are studied by executing tensile and microhardness tests. It is concluded from the graphical analysis of the steepest ascent technique that the optimal maximum and minimum values are 1812–1325 r/min for rotational speed, 43–26 mm/min for welding speed, and 2°–1.3° for tilt angle, respectively. Besides, optical microscope and scanning electron microscope are utilized for microstructural and fractographic analyses for a better understanding of the process.

Theory of the oscillations of an ellipsoidal weld pool in laser welding

1991 ◽  
Vol 24 (8) ◽  
pp. 1288-1292 ◽  
Author(s):  
N Postacioglu ◽  
P Kapadia ◽  
J Dowden
Keyword(s):  
Laser Welding ◽  
Weld Pool
Sign in / Sign up

Export Citation Format

Share Document