scholarly journals Evaluation of Strength of Plain Cement Concrete with Partial Replacement of Cement by Meta Kaolin Fly Ash

2015 ◽  
Vol V4 (05) ◽  
Author(s):  
Nikhil K. Kulkarni ◽  
Ajay A. Hamane ◽  
Keyword(s):  
Fly Ash ◽  
Partial Replacement ◽  
Cement Concrete

scholarly journals INVESTIGATION OF MECHANICAL PROPERTIES OF PAVER BLOCK MADE WITH EVA POLYMERS AND FLY ASH

2021 ◽  
Vol 9 (02) ◽  
pp. 694-702
Author(s):  
K. Hariharan ◽  
◽  
A. Krishna Moorthy ◽  
Keyword(s):  
Fly Ash ◽  
Coarse Aggregate ◽  
Block Design ◽  
Mix Design ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Curing Process ◽  
Cement Concrete ◽  
Ethyl Vinyl ◽  
Water Absorption Test

The aim of the project is to replace cement with fly ash and course aggregate with Ethyl Vinyl Acetate (EVA) in paver block. In this thesis paver block design is by using cement concrete mixture of mix design M30 which is composed of 10mm coarse aggregate cement and fine aggregate (M-sand).In this thesis the cement is partially replaced with fly ash and partial replacement of EVA with coarse aggregate in paver block at various level of 5, 10, 15, and 20 percentage of its weight. The paver block curing process is done for 7days and 28days. After curing it is checked for its compression strength, water absorption test and densitytest.

Effect of Accelerated Curing on Strength of Quaternary Blended Cement Concrete with Recycled Aggregate

2021 ◽  
Vol 882 ◽  
pp. 247-253
Author(s):  
Vishal Akula ◽  
M.V.S.S. Sastri ◽  
P. Mahender ◽  
K. Jagannadha Rao
Keyword(s):  
Fly Ash ◽  
Blended Cement ◽  
Recycled Concrete ◽  
Recycled Aggregate ◽  
Partial Replacement ◽  
Concrete Aggregate ◽  
Cement Concrete ◽  
Design Strength ◽  
Accelerated Curing ◽  
Micro Silica

This paper presents the results of an experimental investigation carried out on accelerated curing of Quaternary Blended Cement (QBC) Concrete with and without recycled aggregate. Cement is partially replaced with fly ash, micro silica and nanosilica to produce QBC Concrete. The variables of study include the grade of concrete, powder content and percentage of recycled aggregate. Two grades of concrete M-40 and M-60 were used in this investigation. Based on the earlier studies, fly ash and micro silica are kept constant as 20% and 10% respectively while nanosilica is varied as 2% and 3%. Three percentages of recycled aggregate as partial replacement of natural aggregate (0%, 50% and 75%) were used. Two methods of curing were employed; boiling water method and hot air curing. The test results are encouraging and it is observed that 90% of the design strength could be achieved in one day for both the grades of concrete by curing at 100°C for a period of 3 hours. Keywords: Quaternary Blended Cement Concrete (QBCC), Fly ash (FA), Micro silica (SF), nanosilica (NSF), Recycled Concrete Aggregate (RCA), Accelerated Curing.

Review on Experimental Study on Effect of Corrosion In Reinforced Concrete Fly-Ash Beam

2020 ◽  
pp. 92-96
Author(s):  
Shubham N. Dadgal ◽  
Shrikant Solanke
Keyword(s):  
Fly Ash ◽  
Bond Strength ◽  
Structural Damage ◽  
Pullout Test ◽  
Partial Replacement ◽  
Structural Members ◽  
Accelerated Corrosion ◽  
Resistivity Method ◽  
Electrical Resistivity Method ◽  
Structural Failures

In modern days for structures in coastal areas it has been observed that the premature structural failures are occurs due to corrosion of the reinforcements of the designed structural member. The corrosion causes the structural damage which in turn leads to reduction in the bearing capacity of the concerned structural members. The aim of this study was to study the effect of partial replacement of fly ash to minimize the corrosion effect. Beams were designed and corroded by using artificial method known accelerated corrosion method. The beams were then tested for flexural and bond strength. Also the weight loss of the reinforced bars was been determined using electrical resistivity method. The fly ash will replace by 10% and 15%.The strength will calculate at varying percentage of corrosion at 10% and 15%. Beams will cast at M25 grade concrete. The flexural strength will test by using UTM and the bond strength will calculate using pullout test.

A Review on Utilization of Fly- Ash and Pond-Ash as a Partial Replacement of Cement in Concrete Mix Design

2018 ◽  
pp. 413-418
Author(s):  
Harshkumar Patel ◽  
Yogesh Patel
Keyword(s):  
Fly Ash ◽  
Electricity Generation ◽  
Power Plants ◽  
Renewable Energy Sources ◽  
Thermal Power ◽  
Strength Test ◽  
Partial Replacement ◽  
Pond Ash ◽  
Research Activities ◽  
Ash Disposal

Now-a-days energy planners are aiming to increase the use of renewable energy sources and nuclear to meet the electricity generation. But till now coal-based power plants are the major source of electricity generation. Disadvantages of coal-based thermal power plants is disposal problem of fly ash and pond ash. It was earlier considered as a total waste and environmental hazard thus its use was limited, but now its useful properties have been known as raw material for various application in construction field. Fly ash from the thermal plants is available in large quantities in fine and coarse form. Fine fly ash is used in construction industry in some amount and coarse fly ash is subsequently disposed over land in slurry forms. In India around 180 MT fly is produced and only around 45% of that is being utilized in different sectors. Balance fly ash is being disposed over land. It needs one acre of land for ash disposal to produce 1MW electricity from coal. Fly ash and pond ash utilization helps to reduce the consumption of natural resources. The fly ash became available in coal based thermal power station in the year 1930 in USA. For its gainful utilization, scientist started research activities and in the year 1937, R.E. Davis and his associates at university of California published research details on use of fly ash in cement concrete. This research had laid foundation for its specification, testing & usages. This study reports the potential use of pond-ash and fly-ash as cement in concrete mixes. In this present study of concrete produced using fly ash, pond ash and OPC 53 grade will be carried. An attempt will be made to investigate characteristics of OPC concrete with combined fly ash and pond ash mixed concrete for Compressive Strength test, Split Tensile Strength test, Flexural Strength test and Durability tests. This paper deals with the review of literature for fly-ash and pond-ash as partial replacement of cement in concrete.

GGBS as Partial Replacement of OPC in Cement Concrete – An Experimental Study

2012 ◽  
Vol 2 (11) ◽  
pp. 189-191 ◽  
Author(s):  
Yogendra O Patil ◽  
◽  
P.N.Patil P.N.Patil ◽  
Dr. Arun Kumar Dwivedi
Keyword(s):  
Experimental Study ◽  
Partial Replacement ◽  
Cement Concrete

scholarly journals Behavior of Quarry Rock Dust, Fly Ash and Slag Based Geopolymer Concrete Columns Reinforced with Steel Fibers under Eccentric Loading

2021 ◽  
Vol 11 (15) ◽  
pp. 6740
Author(s):  
Rana Muhammad Waqas ◽  
Faheem Butt
Keyword(s):  
Fly Ash ◽  
Concrete Cover ◽  
Steel Fibers ◽  
Structural Behavior ◽  
Partial Replacement ◽  
Geopolymer Concrete ◽  
Fiber Reinforced ◽  
Conventional Concrete ◽  
Source Materials ◽  
Rock Dust

Geopolymer concrete, also known as an earth-friendly concrete, has been under continuous study due to its environmental benefits and a sustainable alternative to conventional concrete construction. The supplies of many source materials, such as fly ash (FA) or slag (SG), to produce geopolymer concrete (GPC) may be limited; however, quarry rock dust (QRD) wastes (limestone, dolomite, or silica powders) formed by crushing rocks appear virtually endless. Although significant experimental research has been carried out on GPC, with a major focus on the mix design development, rheological, durability, and mechanical properties of the GPC mixes; still the information available on the structural behavior of GPC is rather limited. This has implications in extending GPC application from a laboratory-based technology to an at-site product. This study investigates the structural behavior of quarry-rock-dust-incorporated fiber-reinforced GPC columns under concentric and eccentric loading. In this study, a total of 20 columns with 200 mm square cross-section and 1000 mm height were tested. The FA and SG were used as source materials to produce GPC mixtures. The QRD was incorporated as a partial replacement (20%) of SG. The conventional concrete (CC) columns were prepared as the reference specimens. The effect of incorporating quarry rock dust as a replacement of SG, steel fibers, and loading conditions (concentric and eccentric loading) on the structural behavior of GPC columns were studied. The test results revealed that quarry rock dust is an adequate material that can be used as a source material in GPC to manufacture structural concrete members with satisfactory performance. The general performance of the GPC columns incorporating QRD (20%) is observed to be similar to that of GPC columns (without QRD) and CC columns. The addition of steel fibers considerably improves the loading capacity, ductility, and axial load–displacement behavior of the tested columns. The load capacities of fiber-reinforced GPC columns were about 5–7% greater in comparison to the CC columns. The spalling of concrete cover at failure was detected in all plain GPC columns, whereas the failure mode of all fiber-reinforced GPC columns is characterized with surface cracking leading to disintegration of concrete cover.

Physical and Mechanical Properties of Cement Paste Were Used Partially with Fly Ash and Kaolin Waste

2017 ◽  
Vol 866 ◽  
pp. 199-203
Author(s):  
Chidchanok Chainej ◽  
Suparut Narksitipan ◽  
Nittaya Jaitanong
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Room Temperature ◽  
Physical And Mechanical Properties ◽  
Partial Replacement ◽  
X Ray Diffraction ◽  
X Ray ◽  
Lime Water ◽  
Diffraction Patterns ◽  
Iron Mold

The aims of this research were study the microstructures and mechanical properties for partial replacement of cement with Fly ash (FA) and kaolin waste (KW). Ordinary Portland cement were partially replaced with FA and KW in the range of 25-35% and 10-25% by weight of cement powder. The kaolin waste was ground for 180 minutes before using. The specimen was packing into an iron mold which sample size of 5×5×5 cm3. Then, the specimens were kept at room temperature for 24 hours and were moist cured in the incubation lime water bath at age of 3 days. After that the specimens were dry cured with plastic wrap at age of 3, 7, 14 and 28 days. After that the compounds were examined by x-ray diffraction patterns (XRD) and the microstructures were examined by scanning electron microscopy (SEM). The compressive strength was then investigated.

Sign in / Sign up

Export Citation Format

Share Document