scholarly journals Ultra High Performance Concrete Reinforced with Short Steel and Carbon Fibers

2015 ◽  
Vol 1 ◽  
pp. 193 ◽  
Author(s):  
Genadijs Šahmenko ◽  
Andrejs Krasnikovs ◽  
Artūrs Lukašenoks ◽  
Māris Eiduks
Keyword(s):  
Carbon Fibers ◽  
High Performance ◽  
Bending Strength ◽  
High Performance Concrete ◽  
Steel Fibers ◽  
Cement Matrix ◽  
Cracking Behavior ◽  
Combined Application ◽  
Pull Out ◽  
Bearing Stress

<p class="R-AbstractKeywords"><span lang="EN-US">Fibers are usually used in High Performance Concrete with a purpose to increase bending strength and ductility. Important properties are the peak value of bearing stress (strength) and post-cracking behavior of bended element. In the framework of an experimental part, Ultra High Performance mix compositions were prepared using intensive mixer. Short steel fibers and carbon micro fibers in amount of 1% by volume, as well as its combination were used for cement matrix reinforcing. Results of compressive and bending tests proved an increase of strength value in the case of use both steel and carbon fibers. Carbon fibers were decreased the effect of explosive collapse of the UHPC cement matrix, at the same time still brittle bending behavior was take place. Steel fibers considerably improved bending ductility thanks to a pull-out mechanism of steel fibers. The best results were achieved in the case of combined application of both carbon and steel fibers.</span></p>

scholarly journals On enhancing the mechanical behavior of ultra-high performance concrete through multi-scale fiber reinforcement

2021 ◽  
Author(s):  
Ketan Ragalwar ◽  
William Heard ◽  
Brett Williams ◽  
Dhanendra Kumar ◽  
Ravi Ranade
Keyword(s):  
Mechanical Properties ◽  
High Performance ◽  
High Performance Concrete ◽  
Underlying Mechanism ◽  
Steel Fibers ◽  
Flexural Behavior ◽  
Steel Wool ◽  
Multi Scale ◽  
Pull Out ◽  
Fiber Matrix

Steel fibers are typically used in ultra-high performance concretes (UHPC) to impart flexural ductility and increase fracture toughness. However, the mechanical properties of the steel fibers are underutilized in UHPC, as evidenced by the fact that most of the steel fibers pull out of a UHPC matrix largely undamaged during tensile or flexural tests. This research aims to improve the bond between steel fibers and a UHPC matrix by using steel wool. The underlying mechanism for fiber-matrix bond improvement is the reinforcement of the matrix tunnel, surrounding the steel fibers, by steel wool. Single fiber pullout tests were performed to quantify the effect of steel wool content in UHPC on the fiber-matrix bond. Microscopic observations of pulled-out fibers were used to investigate the fiber-matrix interface. Compared to the control UHPC mixture with no steel wool, significant improvement in the flexural behavior was observed in the UHPC mixtures with steel wool. Thus, the addition of steel wool in steel fiber-reinforced UHPC provides multi-scale reinforcement that leads to significant improvement in fiber-matrix bond and mechanical properties of UHPC.

scholarly journals Pullout Response of Ultra-High-Performance Concrete with Twisted Steel Fibers

2019 ◽  
Vol 9 (4) ◽  
pp. 658 ◽  
Author(s):  
Judong Ye ◽  
Guohua Liu
Keyword(s):  
High Performance ◽  
High Performance Concrete ◽  
Concrete Surface ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Theoretical Formula ◽  
Element Analysis ◽  
Pullout Force ◽  
Pull Out ◽  
Before And After

This paper aims to develop a pullout force formula and increase the understanding of the damage mechanisms of ultra-high-performance fiber reinforced concrete (UHPFRC) with twisted steel fibers (TSFs) through a pull-out test and finite element analysis (FEA). The formula was first obtained through a theoretical force analysis with model assumptions that are based on the experimental data in the literature. A microscale in-situ X-ray computed tomography (µXCT) was used to prepare 3D images of the cross-section of concrete before and after TSFs with three embedment lengths were pulled out. The tested pullout force values were used for comparison with the developed formula values. The µXCT images show the concrete matrix was preserved after the TSF was pulled out, indicating the stable pullout force values at the strain hardening stage was mainly caused by the fiber untwisting. FEA results show this untwisting behavior occurs on the effective untwisting length of TSF close to the exterior concrete surface. The theoretical formula values were found match well with the testing data. The developed formula is potentially used to analyze the pullout behavior of TSF with different geometries; thus, the design of the UHPFRC with TSFs can be optimized in the field.

scholarly journals Resistance of an Optimized Ultra-High Performance Fiber Reinforced Concrete to Projectile Impact

Buildings ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 63
Author(s):  
Anna L. Mina ◽  
Michael F. Petrou ◽  
Konstantinos G. Trezos
Keyword(s):  
Reinforced Concrete ◽  
High Performance ◽  
High Performance Concrete ◽  
High Strength ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Fiber Reinforced ◽  
Depth Of Penetration ◽  
Projectile Impact ◽  
High Performance Fiber

The scope of this paper is to investigate the performance of ultra-high performance fiber reinforced concrete (UHPFRC) concrete slabs, under projectile impact. Mixture performance under impact loading was examined using bullets with 7.62 mm diameter and initial velocity 800 m/s. The UHPFRC, used in this study, consists of a combination of steel fibers of two lengths: 6 mm and 13 mm with the same diameter of 0.16 mm. Six composition mixtures were tested, four UHPFRC, one ultra-high performance concrete (UHPC), without steel fibers, and high strength concrete (HSC). Slabs with thicknesses of 15, 30, 50, and 70 mm were produced and subjected to real shotgun fire in the field. Penetration depth, material volume loss, and crater diameter were measured and analyzed. The test results show that the mixture with a combination of 3% 6 mm and 3% of 13 mm length of steel fibers exhibited the best resistance to projectile impact and only the slabs with 15 mm thickness had perforation. Empirical models that predict the depth of penetration were compared with the experimental results. This material can be used as an overlay to buildings or to construct small precast structures.

scholarly journals Materials for Production of High and Ultra-High Performance Concrete: Review and Perspective of Possible Novel Materials

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4304
Author(s):  
Markssuel Teixeira Marvila ◽  
Afonso Rangel Garcez de de Azevedo ◽  
Paulo R. de de Matos ◽  
Sergio Neves Monteiro ◽  
Carlos Maurício Fontes Vieira
Keyword(s):  
High Performance ◽  
High Performance Concrete ◽  
Review Article ◽  
Cement Matrix ◽  
Bibliographic Databases ◽  
Future Research ◽  
Chemical Additives ◽  
Ultra High Performance Concrete ◽  
Conventional Concrete ◽  
Essential Components

This review article proposes the identification and basic concepts of materials that might be used for the production of high-performance concrete (HPC) and ultra-high-performance concrete (UHPC). Although other reviews have addressed this topic, the present work differs by presenting relevant aspects on possible materials applied in the production of HPC and UHPC. The main innovation of this review article is to identify the perspectives for new materials that can be considered in the production of novel special concretes. After consulting different bibliographic databases, some information related to ordinary Portland cement (OPC), mineral additions, aggregates, and chemical additives used for the production of HPC and UHPC were highlighted. Relevant information on the application of synthetic and natural fibers is also highlighted in association with a cement matrix of HPC and UHPC, forming composites with properties superior to conventional concrete used in civil construction. The article also presents some relevant characteristics for the application of HPC and UHPC produced with alkali-activated cement, an alternative binder to OPC produced through the reaction between two essential components: precursors and activators. Some information about the main types of precursors, subdivided into materials rich in aluminosilicates and rich in calcium, were also highlighted. Finally, suggestions for future work related to the application of HPC and UHPC are highlighted, guiding future research on this topic.

Sign in / Sign up

Export Citation Format

Share Document