scholarly journals The influence of the profile-dividing grinding strategy on the surface accuracy and roughness of a gear teeth

Mechanik ◽  
2018 ◽  
Vol 91 (8-9) ◽  
pp. 737-740 ◽  
Author(s):  
Piotr Zyzak ◽  
Paweł Kobiela ◽  
Arnold Brożek ◽  
Marek Gabryś
Keyword(s):  
Surface Roughness ◽  
Grinding Wheel ◽  
Machining Accuracy ◽  
Cylindrical Gear ◽  
Gear Teeth ◽  
Surface Accuracy ◽  
Number Of Passes

In the paper are presented investigation results of an effects of adopted strategy of profile-dividing grinding of a cylindrical gear teeth, performed on the Rapid Höfler 900 grinder, on machining accuracy and surface roughness of the teeth. The strategies have taken into considerations changes in the following parameters determining obtained results of the grinding: number of passes, number of leads, shaping method of the grinding wheel.

Grinding Technology of Cylindrical Surface with Protrusion

2016 ◽  
Vol 1136 ◽  
pp. 54-59
Author(s):  
Kazuya Kato ◽  
Yukio Maeda ◽  
Hideaki Tanaka
Keyword(s):  
Surface Roughness ◽  
Cylindrical Surface ◽  
Consumer Electronics ◽  
Grinding Wheel ◽  
Machining Accuracy ◽  
Grinding Process ◽  
Machining Efficiency ◽  
Highly Efficient ◽  
Cylindrical Parts ◽  
Uneven Wear

Cylindrical parts with a protrusion are expected to be used in the components of consumer electronics and automotive products. The machining efficiency of these parts is very low, making them difficult to be mass-produced. The aim of our present work is to develop a highly accurate and highly efficient grinding process for a cylindrical surface with a protrusion. This paper describes the results of experiments using a straight cup-shaped grinding wheel. The following conclusions can be drawn. (1) To prevent uneven wear of the grinding wheel, an oscillation operation is necessary during the grinding process. (2) By employing the straight cup-shaped grinding wheel, the grinding process is realized with the aim of achieving the following: high machining accuracy, roundness below 3 μm, straightness below 2 μm, and surface roughness below 2 μmRzjis.

scholarly journals An Analysis of the Surface Geometric Structure and Geometric Accuracy of Cylindrical Gear Teeth Manufactured with the Direct Metal Laser Sintering (DMLS) Method

2019 ◽  
Author(s):  
Jadwiga Małgorzata Pisula ◽  
Grzegorz Budzik ◽  
Łukasz Przeszłowski
Keyword(s):  
Surface Roughness ◽  
Geometric Structure ◽  
Gear Tooth ◽  
Spur Gear ◽  
Laser Sintering ◽  
Tooth Surface ◽  
Direct Metal Laser Sintering ◽  
Cylindrical Gear ◽  
Sand Blasting ◽  
Gear Teeth

This paper presents findings concerning the accuracy of the geometry of cylindrical spur gear teeth manufactured with the direct metal laser sintering (DMLS) method. In addition, the results of the evaluation of the tooth surface geometric structure are presented in the form of selected two-dimensional and three-dimensional surface roughness parameters. An analysis of the accuracy of the fabricated gear teeth was performed after gear sand-blasting and gear tooth milling processes. Surface roughness was measured before and after sand-blasting and gear tooth milling. The test gear wheel was manufactured from GP1 high-chromium stainless steel on an EOS M270 machine.

Effect of Contact Stiffness of Grinding Wheel on Ground Surface Roughness and Residual Stock Removal of Workpiece

2013 ◽  
Vol 797 ◽  
pp. 522-527
Author(s):  
Taisei Yamada ◽  
Hwa Soo Lee ◽  
Kohichi Miura
Keyword(s):  
Surface Roughness ◽  
Contact Stiffness ◽  
Ground Surface ◽  
Grinding Wheel ◽  
Machining Accuracy ◽  
Grinding Wheels ◽  
Residual Stock ◽  
Grinding Operations ◽  
Stock Removal ◽  
Ground Surface Roughness

In the grinding operation, grinding wheels are deformed by grinding forces, so that residual stock removal of the workpiece takes place. Since this residual stock removal of the workpiece causes low machining efficiency and deterioration of machining accuracy, high hardness grinding wheels may be selected in order to obtain high machining efficiency and/or high quality machining accuracy. On the other hand, when grinding operations used by low hardness grinding wheels are carried out, it is well known that ground surface roughness is smaller than in case of higher hardness grinding wheels. From such a viewpoint, this study aims to investigate experimentally the effect of the contact stiffness of grinding wheel on the ground surface roughness and the residual stock removal of the workpiece. Grinding operations were carried out using three grinding wheels which are different hardness type, and ground surface roughness and residual stock removal of the workpiece were measured. The contact stiffness of grinding wheel was calculated by a support stiffness of single abrasive grain and a contact area between grinding wheel and workpiece. Comparing the contact stiffness of grinding wheel with the ground surface roughness and the residual stock removal of the workpiece, it was known that ground surface roughness increases and residual stock removal of workpiece decreases with increaseing the contact stiffness of grinding wheel. From these results, since elastic deformation of the grinding wheel changed depending on the suppot stiffness of single abrasive grain, it was clarified that the ground surface roughness and the residual stock removal of the workpiece were changed by the contact stiffness of grinding wheel.

Study on the Effect of Coarse Grinding Area Slope Angle on Surface Quality in Point Grinding

2013 ◽  
Vol 797 ◽  
pp. 118-122 ◽  
Author(s):  
Ya Dong Gong ◽  
Guo Qiang Yin ◽  
Chao Wang ◽  
Xue Long Wen ◽  
Jun Cheng
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Deflection Angle ◽  
Slope Angle ◽  
Grinding Wheel ◽  
Machining Accuracy ◽  
Stepped Shaft ◽  
Vitrified Bond ◽  
Design And Manufacture

There is a vitrified bond CBN point grinding wheel with coarse grinding area slope angle θ. This new grinding wheel has higher removing rate and better machining accuracy than conventional wheels. The design and manufacture principle of the new grinding wheels are studied in this paper. These wheels with different coarse grinding area slope angle θ are used to grind the stepped shaft of QT700 with a series of grinding parameters.VHX-1000E microscopic system and Micromeasure system are used to measure the surface quality of workpiece. In the same group of grinding parameters, compare the effect of these different wheels on surface roughness. The effect of deflection angle α on surface roughness is generalized.

Evaluating the influence of grinding mode on part’s accuracy and grinding wheel’s wear in grinding profile for ball bearing's inner ring groove

2018 ◽  
Vol 56 (4) ◽  
pp. 531
Author(s):  
Nguyen Anh Tuan ◽  
Vu Toan Thang ◽  
Nguyen Viet Tiep
Keyword(s):  
Theoretical Analysis ◽  
Current Issue ◽  
Grinding Wheel ◽  
Machining Accuracy ◽  
Ring Groove ◽  
Production Practice ◽  
Wear Of Grinding Wheel ◽  
Output Factors ◽  
Grinding Operations ◽  
Technological Mode

Determining the influence of technological mode factors on machining accuracy is always an current issue in the production practice especially for grinding operations. This paper presents some research results to determine the effect of grinding parameters on grinding wheel’s wear and part’s accuracy in grinding profile for ball bearing's inner ring groove. From theoretical analysis and experimental results, the article assesses the influence of grinding mode factors on output factors. Based on that, the economic limitation wear of grinding wheel at three different grinding modes is determined.

scholarly journals Study on the Effect of Grinding Pressure on Material Removal Behavior Performed on a Self-Designed Passive Grinding Simulator

2021 ◽  
Vol 11 (9) ◽  
pp. 4128
Author(s):  
Peng-Zhan Liu ◽  
Wen-Jun Zou ◽  
Jin Peng ◽  
Xu-Dong Song ◽  
Fu-Ren Xiao
Keyword(s):  
Residual Stress ◽  
Surface Roughness ◽  
Service Life ◽  
Material Removal ◽  
Removal Rate ◽  
Grinding Force ◽  
Grinding Wheel ◽  
Grinding Process ◽  
Grinding Temperature ◽  
Grinding Efficiency

Passive grinding is a new rail grinding strategy. In this work, the influence of grinding pressure on the removal behaviors of rail material in passive grinding was investigated by using a self-designed passive grinding simulator. Meanwhile, the surface morphology of the rail and grinding wheel were observed, and the grinding force and temperature were measured during the experiment. Results show that the increase of grinding pressure leads to the rise of rail removal rate, i.e., grinding efficiency, surface roughness, residual stress, grinding force and grinding temperature. Inversely, the enhancement of grinding pressure and grinding force will reduce the grinding ratio, which indicates that service life of grinding wheel decreases. The debris presents dissimilar morphology under different grinding pressure, which reflects the distinction in grinding process. Therefore, for rail passive grinding, the appropriate grinding pressure should be selected to balance the grinding quality and the use of grinding wheel.

Surface integrity of quenched steel 1045 machined by CBN grinding wheel and SiC grinding wheel

2017 ◽  
Vol 8 (2) ◽  
pp. 179-187 ◽  
Author(s):  
Kankan Ji ◽  
Xingquan Zhang ◽  
Shubao Yang ◽  
Liping Shi ◽  
Shiyi Wang ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Surface Morphology ◽  
Compressive Stress ◽  
Surface Integrity ◽  
Grinding Wheel ◽  
Micro Hardness ◽  
Content Type ◽  
Quenched Steel ◽  
Cut Depth ◽  
Cbn Grinding Wheel

Purpose The purpose of this paper is to evaluate surface integrity of quenched steel 1045 ground drily by the brazed cubic boron nitride (CBN) grinding wheel and the black SiC wheel, respectively. Surface integrity, including surface roughness, sub-surface hardness, residual stresses and surface morphology, was investigated in detail, and the surface quality of samples ground by two grinding wheels was compared. Design/methodology/approach In the present work, surface integrity of quenched steel 1045 machined by the CBN grinding wheel and the SiC wheel was investigated systematically. All the specimens were machined with a single pass in the down-cutting mode of dry condition. Surface morphology of the ground specimen was observed by using OLYMPUS BX51M optical microscopy. Surface roughness of seven points was measured by using a surface roughness tester at a cut-off length of 1.8 mm and the measurement traces were perpendicular to the grinding direction. Sub-surface micro-hardness was measured by using HVS-1000 digital micro-hardness tester after the cross-section surface was polished. The residual stress was tested by using X-350A X-ray stress analyzer. Findings When the cut depth is increased from 0.01 to 0.07 mm, the steel surface machined by the CBN wheel remains clear grinding mark, lower roughness, higher micro-hardness and higher magnitude of compressive stress and fine microstructure, while the surface machined by the SiC grinding wheel becomes worse with increasing of cut depth. The value of micro-hardness decreases, and the surface roughness increases, and the surface compressive stress turns into tensile stress. Some micro-cracks and voids occur when the sample is processed by the SiC grinding wheel with cut depth 0.07 mm. Originality/value In this paper, the specimens of quenched steel 1045 were machined by the CBN grinding wheel and the SiC wheel with various cutting depths. The processing quality resulted from the CBN grinding wheel is better than that resulted from the SiC grinding wheel.

scholarly journals Performance of Norton Quantum Grinding Wheels

2016 ◽  
Vol 686 ◽  
pp. 125-130 ◽  
Author(s):  
Miroslav Neslušan ◽  
Jitka Baďurová ◽  
Anna Mičietová ◽  
Maria Čiliková
Keyword(s):  
Surface Roughness ◽  
Ground Surface ◽  
Bearing Steel ◽  
Grinding Wheel ◽  
Grinding Wheels ◽  
Grinding Forces ◽  
Removal Rates ◽  
Surface Burn ◽  
Conventional Grinding

This paper deals with cutting ability of progressive Norton Quantum grinding wheel during grinding roll bearing steel 100Cr6 of hardness 61 HRC. Cutting ability of this wheel is compared with conventional grinding wheel and based on measurement of grinding forces as well as surface roughness. Results of experiments show that Norton Quantum grinding wheels are capable of long term grinding cycles at high removal rates without unacceptable occurrence of grinding chatter and surface burn whereas application of conventional wheel can produce excessive vibration and remarkable temper colouring of ground surface. Moreover, while Norton Quantum grinding wheel gives nearly constant grinding forces and surface roughness within ground length at higher removal rates, conventional grinding wheel (as that reported in this study) does not.

Vibration Analysis of ID Slicing Process and Wafer Measurement

2006 ◽  
Vol 315-316 ◽  
pp. 641-645 ◽  
Author(s):  
Xin Wei ◽  
Rui Wei Huang ◽  
Shao Hui Lai ◽  
Z.H. Xie
Keyword(s):  
Surface Roughness ◽  
Power Spectrum ◽  
Vibration Analysis ◽  
Machining Accuracy ◽  
Radial Vibration ◽  
Total Thickness ◽  
Axial Vibration ◽  
Vibration Signals ◽  
Measurement And Analysis ◽  
Inner Diameter

ID (inner-diameter) slicing is widely used in cutting ingots currently. In this paper, the deflection (axial vibration) and vibration (radial vibration) signals in different slicing conditions of the silicon wafers were measured online and analyzed. The effects of the vibration signals on the machining accuracy and surface roughness of sliced wafers were investigated based on the measurement and analysis of the surface roughness, warpage and TTV (total thickness vibration) of the sliced wafers. The results show that the changes of surface roughness, warpage and TTV of the sliced wafers exhibit approximately consistence with the changes of the power spectrums of the acquired vibration signals in different working stage of the blade. The vibration and deflection signals can give evidence of the changes in the cutting forces and blade performance during slicing. The power spectrum of the signals is useful for monitoring the blade wear and tension condition and predicting the surface quality and machining accuracy of the sliced wafers.

Development of a New Plate Polishing Technique with an Instantaneous Tiny-Grinding Wheel Cluster Based on Magnetorheological Effect

2008 ◽  
Vol 53-54 ◽  
pp. 155-160 ◽  
Author(s):  
Qiu Sheng Yan ◽  
Ai Jun Tang ◽  
Jia Bin Lu ◽  
Wei Qiang Gao
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Grinding Wheel ◽  
Abrasive Particles ◽  
Magnetorheological Effect ◽  
Material Removal Model ◽  
Mr Effect ◽  
Removal Model

A new plate polishing technique with an instantaneous tiny-grinding wheel cluster based on the magnetorheological (MR) effect is presented in this paper, and some experiments were conducted to prove its effectiveness and applicability. Under certain experimental condition, the material removal rate was improved by a factor of 20.84% as compared with the conventional polishing methods with dissociative abrasive particles, while the surface roughness of the workpiece was not obviously increased. Furthermore, the composite of the MR fluid was optimized to obtain the best polishing performance. On the basis of the experimental results, the material removal model of the new plate polishing technique was presented.

Sign in / Sign up

Export Citation Format

Share Document