scholarly journals Preparation and Characterization of Green Epoxy Resin Composites and Its Use in Corrosion Resistance

2018 ◽  
Author(s):  
Abbas Hassan Faris
Keyword(s):  
Bisphenol A ◽  
Epoxy Resin ◽  
Electrolyte Solutions ◽  
Kraft Lignin ◽  
Diglycidyl Ether ◽  
Kraft Pulping ◽  
Palm Tree ◽  
Scanning Calorimetry ◽  
Ft Ir ◽  
Nano Titanium Dioxide

In this work, appropriate alternative for diglycidyl ether bisphenol A (DGEBA) was found to avoid the destructive effects of bisphenol A. Lignin, an aromatic compound from palm tree leaves, was used as a renewable material to synthesize a bio-based epoxy resin. Lignin extracted using Kraft pulping process. Kraft Lignin was epoxidized with epichlorohydrin in alkaline medium. Nano-titanium dioxide was used as filler with ratio of 10% to prepare the green epoxy composite. The structure of the Kraft lignin and lignin-based epoxy resin was proven via Infrared spectra (FT-IR) were recorded using solid KBr disk by testing Shimadzu (FT-IR-8300) spectrophotometer. The thermal properties of the curing process of lignin-based epoxy resin and composite were investigate using Differential scanning calorimetry (DSC) analysis. Potentiodynamic measurements data revealed that the anti-corrosion performance of the lignin based epoxy resin. The study demonstrates successful of epoxidation of Kraft lignin. In addition, lignin based eopxy resin showed effective inhibitor for carbon steel in 3.5 wt. % NaCl electrolyte solutions

Cationic Catalyst as Latent Curing Agent for Epoxy Resin

2015 ◽  
Vol 749 ◽  
pp. 126-128 ◽  
Author(s):  
Ho Kyoung Choi ◽  
Bong Goo Choi ◽  
Yong Yoon Lee ◽  
Jae Sik Na
Keyword(s):  
Thermal Stability ◽  
Elevated Temperature ◽  
Bisphenol A ◽  
Epoxy Resin ◽  
Chemical Conversion ◽  
Diglycidyl Ether ◽  
Curing Agent ◽  
Good Thermal Stability ◽  
Ft Ir ◽  
Cure Temperature

1-Benzyl-3-methyl-imidazolium hexafluoroantimonate (BMH) was newly synthesized and characterized with FT-IR, 1H-NMR. We synthesized catalysts fulfill requirements for a rapid cure at a moderately elevated temperature in curing the epoxy resin for neat diglycidyl ether bisphenol A (DGBEA). The cure behavior of this resin was investigated at elevated temperature and cure temperature in the presence of 0.5, 1.0, 2.0 wt% of 1-benzyl-3-methyl-imidazolium hexafluoroantimonate (BMH) by mean of differential scanning calorimeter (DSC). Chemical conversion as function of temperature and amount of BMH (0.5, 1.0, 2.0 wt%) were determined from DSC. It was found that BMH were superior latent thermal catalyst for catinonic curing which have a good thermal stability.

scholarly journals Surface Properties of Poly(Hydroxyurethane)s Based on Five-Membered Bis-Cyclic Carbonate of Diglycidyl Ether of Bisphenol A

Materials ◽  
2020 ◽  
Vol 13 (22) ◽  
pp. 5184
Author(s):  
Mariusz Tryznowski ◽  
Zuzanna Żołek-Tryznowska
Keyword(s):  
Bisphenol A ◽  
Surface Properties ◽  
Rheological Characteristic ◽  
13C Nmr Spectroscopy ◽  
Cyclic Carbonate ◽  
Contact Angles ◽  
Diglycidyl Ether ◽  
Scanning Calorimetry ◽  
Static Contact ◽  
Ft Ir

Poly(hydroxyurethane)s (PHU) are alternatives for conventional polyurethanes due to the use of bis-cyclic dicarbonates and diamines instead of harmful and toxic isocyanates. However, the surface properties of poly(hydroxyurethane)s are not well known. In this work, we focus on the analysis of the surface properties of poly(hydroxyurethane) coatings. Poly(hydroxyurethane)s were obtained by a catalyst-free method from commercially available carbonated diglycidyl ether of bisphenol A (Epidian 6 epoxy resins) and various diamines: ethylenediamine, trimethylenediamine, putrescine, hexamethylenediamine, 2,2,4(2,4,4)-trimethyl-1,6-hexanediamine, m-xylylenediamine, 1,8-diamino-3,6-dioxaoctane, 4,7,10-trioxa-1,13-tridecanediamine, and isophorone diamine, using a non-isocyanate route. The structures of the obtained polymers were confirmed by FT-IR, 1H NMR and 13C NMR spectroscopy, and thermogravimetric (TGA) and differential scanning calorimetry (DSC) analyses were performed. The rheological characteristic of the obtained polymers is presented. The static contact angles of water, diidomethane, and formamide, deposited on PHU coatings, were measured. From the measured contact angles, the surface free energy was calculated using two different approaches: Owens–Wendt and van Oss–Chaudhury–Good. Moreover, the wetting envelopes of PHU coatings were plotted, which enables the prediction of the wetting effect of various solvents. The results show that in the investigated coatings, a mainly dispersive interaction occurs.

Study on curing kinetics of a diglycidyl ether of bisphenol A epoxy resin/microencapsulated curing agent system

2012 ◽  
Vol 24 (8) ◽  
pp. 730-737 ◽  
Author(s):  
Wang Fang ◽  
Xiao Jun ◽  
Wang Jing-wen ◽  
Li Shu-qin
Keyword(s):  
Particle Size ◽  
Bisphenol A ◽  
Epoxy Resin ◽  
Diglycidyl Ether ◽  
Wall Material ◽  
Curing Agent ◽  
Resin System ◽  
Scanning Calorimetry ◽  
Cure Reaction ◽  
Epoxy Resin System

A modified imidazole curing agent, EMI-g-BGE, was encapsulated for one-package of diglycidyl ether of bisphenol A (DGEBA) epoxy resin system. Polyetherimide (PEI) was used as the wall material, and the emulsion solvent evaporation method was used to form the microcapsules. The morphology and particle size distribution of microcapsules were evaluated by scanning electron microscopy (SEM), mastersizer analyzer. Microcapsules exhibited spherical shapes and the mean particle size was about 745 nm. The curing kinetic of DGEBA/microcapsules curing agent was studied by nonisothermal differential scanning calorimetry (DSC) technique at different heating rates. Dynamic DSC scans indicated the microcapsule was an effective curing agent of epoxy resin. The apparent activation energy Ea was 88.03 kJ/mol calculated through Kissinger method, more than DGEBA/EMI-g-BGE system. This microcapsule of EMI-g-BGE exhibited a long shelf life, and the curing did not occur in this epoxy-microcapsule resin system for more than 3months at room temperature. The kinetic parameters were determined by Málek method and a two-parameter ( m, n) autocatalytic model (Šesták–Berggren equation) was found to be the most adequate selected kinetic model, which showed the encapsulation of the curing agent EMI-g-BGE did not change the cure reaction mechanism of the epoxy resin system. From the experimental data, the nonisothermal DSC curves show the results being in accordant with those theoretically calculated.

Evaluation of bisphenol A-based epoxy resin containing multiwalled carbon nanotubes to improve resistance to degradation

2018 ◽  
Vol 53 (21) ◽  
pp. 2981-2991 ◽  
Author(s):  
Sameer A Awad ◽  
Christopher M Fellows ◽  
Seyed S Mahini
Keyword(s):  
Bisphenol A ◽  
Epoxy Resin ◽  
Uv Light ◽  
Tensile Tests ◽  
Diglycidyl Ether ◽  
Accelerated Weathering ◽  
Scanning Calorimetry ◽  
Multiwalled Carbon ◽  
Epoxy Nanocomposite ◽  
Before And After

The influence of exposure to UV light and moisture on the durability of a multiwalled carbon nanotube(MWCNT)/epoxy nanocomposite was investigated. Samples of epoxy resin based on diglycidyl ether of bisphenol A (DGEBA) cured with 2,2,4-trimethylene-1,6-hexadiamine (TMDA), and epoxy nanocomposite containing 0.5% MWCNT were exposed to different accelerated weathering times between one and six months. Changes in surface chemistry, mechanical properties (tensile tests), thermal properties (thermogravimetric analysis and differential scanning calorimetry), and morphology were evaluated before and after exposure to accelerated weathering for a period of up to six months. Epoxy nanocomposite (DGEBA–TMDA/0.5%MWCNT) samples had improved thermal stability and resistance to degradation, compared to epoxy resin (DGEBA–TMDA). The effect of MWCNT at reducing degradation was more pronounced than previously found for resins prepared with hydrogenated DGEBA.

Diglycidyl ether of bisphenol-A epoxy resin modified using poly(ether ether ketone) with pendenttert-butyl groups

2007 ◽  
Vol 45 (17) ◽  
pp. 2481-2496 ◽  
Author(s):  
Bejoy Francis ◽  
Sabu Thomas ◽  
R. Sadhana ◽  
Nicole Thuaud ◽  
R. Ramaswamy ◽  
...  
Keyword(s):  
Bisphenol A ◽  
Epoxy Resin ◽  
Diglycidyl Ether ◽  
Ether Ether Ketone ◽  
Poly Ether Ether Ketone ◽  
Ether Ketone

Investigating the relationship between tack and degree of conversion in DGEBA-based epoxy resin cured with dicyandiamide and diuron

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Ali Kuliaei ◽  
Iraj Amiri Amraei ◽  
Seyed Rasoul Mousavi
Keyword(s):  
Epoxy Resin ◽  
Reaction Order ◽  
Theoretical Data ◽  
Cure Kinetics ◽  
Diglycidyl Ether ◽  
Degree Of Conversion ◽  
Ozawa Method ◽  
Heating Rates ◽  
Scanning Calorimetry ◽  
Kinetics Of

Abstract The purpose behind this research was to determine the optimum formulation and investigate the cure kinetics of a diglycidyl ether of bisphenol-A (DGEBA)-based epoxy resin cured by dicyandiamide and diuron for use in prepregs. First, all formulations were examined by the tensile test, and then, the specimens with higher mechanical properties were further investigated by viscometry and tack tests. The cure kinetics of the best formulation (based on tack test) in nonisothermal mode was investigated using differential scanning calorimetry at different heating rates. Kissinger and Ozawa method was used for determining the kinetic parameters of the curing process. The activation energy obtained by this method was 71.43 kJ/mol. The heating rate had no significant effect on the reaction order and the total reaction order was approximately constant ( m + n ≅ 2.1 $m+n\cong 2.1$ ). By comparing the experimental data and the theoretical data obtained by Kissinger and Ozawa method, a good agreement was seen between them. By increasing the degree of conversion, the viscosity decreased; as the degree of conversion increased, so did the slope of viscosity. The results of the tack test also indicated that the highest tack could be obtained with 25% progress of curing.

Azomethine ether-based potential curing agent for epoxy resin (diglycidyl ether of bisphenol A): Synthesis and characterization

2020 ◽  
pp. 009524432092857
Author(s):  
Fozia Noreen ◽  
Ahtaram Bibi ◽  
Naila Khalid ◽  
Imran Ullah Khan
Keyword(s):  
Spectral Analysis ◽  
Bisphenol A ◽  
Light Emission ◽  
Condensation Reaction ◽  
Stokes Shift ◽  
Green Light ◽  
Diglycidyl Ether ◽  
Proton Nuclear Magnetic Resonance ◽  
Curing Agent ◽  
Scanning Calorimetry

Novel azomethine ether-based compounds (A: N-((4-(9-(4-(phenylimino)methyl)phenoxy)nonyloxy)benzylidene)bezenamine and B: N-((4-(9-(4-(p-hydroxyphenylimino)methyl)phenoxy)nonyloxy)benzylidene)-4-hydroxybenzenamine) were synthesized by condensation reaction of dialdehyde, 4,4-(1,9-nonandiyle)bis(oxy)dibenzaldehyde with aromatic amines. Structures of synthesized compounds were successfully characterized by Fourier transform infrared (FTIR), ultraviolet–visible, proton nuclear magnetic resonance imaging and photoluminescence (PL) spectroscopy. The PL spectral analysis revealed that emission maxima of compounds A and B are at 475 and 500 nm, respectively, indicate blue and green light emission with large Stokes shift range (Δ λ ST, 109–138 nm). Two series of polymers: one azomethine-based polymers (C1–C5) and other without azomethine (H1–H4) were prepared by curing diglycidyl ether of bisphenol A with a synthesized curing agent (B) and commercial curing agent, respectively, in various proportions. The structural characterization of the resulting polymers was carried out by FTIR spectral analysis. Thermal properties revealed that azomethine-based polymers (C1–C5) were thermally stable up to 400°C as compared to H1–H4. The glass transition temperature of the polymers, determined by differential scanning calorimetry, was in the range 121–123°C.

scholarly journals Sustainable access to fully biobased epoxidized vegetable oil thermoset materials prepared by thermal or UV-cationic processes

RSC Advances ◽  
2020 ◽  
Vol 10 (68) ◽  
pp. 41954-41966 ◽  
Author(s):  
Samuel Malburet ◽  
Chiara Di Mauro ◽  
Camilla Noè ◽  
Alice Mija ◽  
Marco Sangermano ◽  
...  
Keyword(s):  
Bisphenol A ◽  
Epoxy Resin ◽  
Vegetable Oil ◽  
Epoxy Resins ◽  
Diglycidyl Ether

Beyond the need to find a non-toxic alternative to DiGlycidyl Ether of Bisphenol-A (DGEBA), the serious subject of non-epichlorohydrin epoxy resins production remains a crucial challenge that must be solved for the next epoxy resin generations.

Sign in / Sign up

Export Citation Format

Share Document