scholarly journals Influence of Surcharge Load on the Adjacent Pile Foundation in Coastal Floodplain

2020 ◽  
Vol 3 (1) ◽  
Author(s):  
Hao Zhang ◽  
Kai Sun
Keyword(s):  
Soft Soil ◽  
Three Dimensional ◽  
Bending Moment ◽  
Double Row ◽  
Pile Cap ◽  
Dimensional Finite Element ◽  
Surcharge Load ◽  
Soft Substratum ◽  
And Migration ◽  
Three Dimensional Finite Element

<p><strong> </strong>In this paper, in order to investigate the behavior of existing piles caused by the horizontal and compression deformation of soft substratum due to backfill surcharge on coastal floodplain, three-dimensional finite element models of piles adjacent to surcharge load were established. The deformation and migration law of soft soil was analyzed. The behavior of single pile and double row pile adjacent to surcharge load were studied, in which the influence of surcharge load location, surcharge pressure, pile stiffness, and pile top constraint conditions were considered. The results show that as the position of surcharge load is closer and the surcharge pressure increases, the response (e.g. deformation and bending moment) is more obvious. With the increase of pile stiffness, the range of passive load is increased. The deformation behavior of pile body under different constraints of pile cap is significantly different. The effect of secondary bending moment caused by pile axial force is obvious and cannot be ignored. If there is a thick soft substratum, it is beneficial to improve the behavior of adjacent piles by using cement mixing pile reinforcement.</p>

scholarly journals Internal Force on and Deformation of Steel Assembled Supporting Structure of Foundation Pit under Thermal Stress

2021 ◽  
Vol 11 (5) ◽  
pp. 2225
Author(s):  
Fu Wang ◽  
Guijun Shi ◽  
Wenbo Zhai ◽  
Bin Li ◽  
Chao Zhang ◽  
...  
Keyword(s):  
Three Dimensional ◽  
Bending Moment ◽  
High Strength ◽  
Element Model ◽  
Internal Force ◽  
Foundation Pit ◽  
Dimensional Finite Element ◽  
Influence Of Temperature On ◽  
Scale Experiment ◽  
Three Dimensional Finite Element

The steel assembled support structure of a foundation pit can be assembled easily with high strength and recycling value. Steel’s performance is significantly affected by the surrounding temperature due to its temperature sensitivity. Here, a full-scale experiment was conducted to study the influence of temperature on the internal force and deformation of supporting structures, and a three-dimensional finite element model was established for comparative analysis. The test results showed that under the temperature effect, the deformation of the central retaining pile was composed of rigid rotation and flexural deformation, while the adjacent pile of central retaining pile only experienced flexural deformation. The stress on the retaining pile crown changed little, while more stress accumulated at the bottom. Compared with the crown beam and waist beam 2, the stress on waist beam 1 was significantly affected by the temperature and increased by about 0.70 MPa/°C. Meanwhile, the stress of the rigid panel was greatly affected by the temperature, increasing 78% and 82% when the temperature increased by 15 °C on rigid panel 1 and rigid panel 2, respectively. The comparative simulation results indicated that the bending moment and shear strength of pile 1 were markedly affected by the temperature, but pile 2 and pile 3 were basically stable. Lastly, as the temperature varied, waist beam 2 had the largest change in the deflection, followed by waist beam 1; the crown beam experienced the smallest change in the deflection.

Three-Dimensional Finite Element Analysis of Pipe Flange Connections: The Case of Using Compressed Asbestos Sheet Gasket

2002 ◽  
Author(s):  
Tomohiro Takaki ◽  
Toshimichi Fukuoka
Keyword(s):  
Contact Pressure ◽  
Three Dimensional ◽  
Numerical Procedure ◽  
Bending Moment ◽  
Elastic Interaction ◽  
Bearing Surface ◽  
Element Analysis ◽  
Bolt Stress ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

The most important factor for the leakage problem of pipe flange connections is considered to be contact pressure distribution at the gasket bearing surface in service. In this study, the mechanical behaviors of the pipe flange connection are evaluated using FEM as a three-dimensional contact problem, in which a gasket is modeled as a nonlinear one-dimensional gasket element. Here, the contact pressure distributions at the gasket bearing surface and the variations of the bolt stress are estimated under uniform bolt preloads or nonuniform ones due to the elastic interaction during bolting up. The numerical procedure proposed here can successively deal with the processes of bolt-up, applying inner pressure and applying bending moment. The analytical objects are pipe flanges specified in JIS B 2238 with compressed asbestos sheet gaskets being inserted. The validity of the numerical method is ascertained by experiment.

scholarly journals A Numerical Analysis on the Behavior of Single Battered Pile under Pullout Loading

2021 ◽  
Vol 318 ◽  
pp. 01010
Author(s):  
Mais S. Al-Tememy ◽  
Mohammed A. Al-Neami ◽  
Mohammed F. Asswad
Keyword(s):  
Three Dimensional ◽  
Bending Moment ◽  
Offshore Structures ◽  
Pullout Capacity ◽  
Element Analysis ◽  
Dense Sand ◽  
Dimensional Finite Element ◽  
Pullout Load ◽  
Three Dimensional Finite Element ◽  
3D Software

Batter or raker piles are piles driven at an inclination with a vertical to resist large inclined or lateral forces. Many structures like offshore structures and towers are subjected to overturning moments due to wave pressure, wind load, and ship impacts. Therefore in such structures, a combination of the vertical and batter piles is used to transfer overturning moments in compression and tension forces to the foundation. This paper presents a three-dimensional finite element analysis using PLAXIS 3D software to study the battered pile's behavior under the effect of pullout load. Several variables that influence the pile tension capacity embedded in sandy soil are investigated. The pile models are steel piles embedded in the dense sand at different batter angles (0, 10, 20, and 30) degrees with two embedment ratios, L/d (15 and 20). To clarify the pile shape's influence on a pullout capacity, two shapes are used, a circular pile with a diameter equal to 20 mm and a square pile with a section of 15.7×15.7 mm. These dimensions are chosen to achieve an equal perimeter for both shapes. The numerical results pointed that the pile pullout capacity increases with the increasing of the batter angle and embedment ratio, and the maximum values are marked at a batter angle of 20o. The shape of the bending moment profile is a single curvature, and the peak values are located approximately at the midpoint of the battered pile, while a zero value is located at the pile tip and pile head.

Three-dimensional finite element modelling of a full-scale geosynthetic-reinforced, pile-supported embankment

2015 ◽  
Vol 52 (12) ◽  
pp. 2041-2054 ◽  
Author(s):  
R. Kerry Rowe ◽  
K.-W. Liu
Keyword(s):  
Finite Element ◽  
Soft Soil ◽  
Three Dimensional ◽  
Single Layer ◽  
Full Scale ◽  
Numerical Results ◽  
Element Analysis ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element ◽  
Pile Supported Embankment

The performance of four sections of a full-scale embankment constructed on soft soil is examined using a fully coupled and fully three-dimensional finite element analysis. The four sections had similar embankment loadings but different improvement options (one unimproved, one with pile-support only, one with a single layer geotextile-reinforced platform and pile-support, and one with two layers of geogrid-reinforced platform and pile-support). Like the field data, the numerical results show that the inclusion of piles decreases the settlement at the subsoil surface to 52% of that for the unimproved section, and the addition of a single layer of geotextile reinforcement (J = 800 kN/m) further reduced settlement to only 31% of that of the unimproved section. The effects of geosynthetic reinforcement and multiple layers of reinforcement on the performance of the pile-supported embankment are discussed. The relative load transfer is calculated using eight existing methods and they are compared with the field measurements and numerical results.

Three-Dimensional Finite Element Analysis of Rigid Flanged Shaft Coupling Subjected to Twisting Moment

2013 ◽  
Author(s):  
Koichi Okayama ◽  
Toshimichi Fukuoka
Keyword(s):  
Friction Force ◽  
Shear Force ◽  
Three Dimensional ◽  
Bending Moment ◽  
Shaft Length ◽  
Element Analysis ◽  
Bolt Stress ◽  
Dimensional Finite Element ◽  
Bending Stresses ◽  
Three Dimensional Finite Element

A reamer bolt is commonly used when clamping a rigid shaft coupling subjected to large shear force. Although some joint design procedures assume that the applied shear force transmits only through the reamer surface, it is also supported by the friction force on the contact surfaces. Accordingly, to design the coupling clamped by reamer bolts, it is important to evaluate the ratio of the shear forces supported by the reamer surface and the friction force, which is defined as shear force transfer ratio (SFTR) here. In this study, distributions of SFTR and the bending stresses along the reamer surface are analyzed by three-dimensional FEM, focusing on the effects of the fit between the reamer bolt and bolt hole, the scatter of initial bolt stress and the misalignment of the connecting shafts. Numerical results quantitatively clarify how the amounts of the SFTR and the bending stresses as the friction coefficients, the fit and the magnitude of misalignment are changed. As for an offset misalignment, it is found that its effect on the bending moment generated in the shaft body is negligibly small, if the offset between two shafts in radial direction is less than 10mm which is 1% of the total shaft length.

scholarly journals A hybrid analytical-numerical solution for a circular pile under lateral load in multilayered soil

2020 ◽  
Vol 14 (1) ◽  
pp. 1-14
Author(s):  
Nghiem Xuan Hien
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Differential Equations ◽  
Numerical Solution ◽  
Elastic Foundation ◽  
Three Dimensional ◽  
Bending Moment ◽  
Lateral Load ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

A hybrid analytical-numerical solution is proposed to solve the problem of a laterally loaded pile with a circular cross-section in multilayered soils. In the pile-soil model, the lateral load is located at the pile head including both lateral force and bending moment. The single pile is considered as a beam on elastic foundation while shear beams model the soil column below the pile toe. The differential equations governing pile deflections are derived based on the energy principles and variational approaches. The differential equations are solved iteratively by using the finite element method that provides results of pile deflection, rotation angle, shear force, and bending moment along the pile and equivalent stiffness of the pile-soil system. The modulus reduction equation is also developed to match the proposed results well to the three-dimensional finite element analyses. Several examples are conducted to validate the proposed method by comparing the analysis results with those of existing analytical solutions, the three-dimensional finite element solutions. Keywords: beam on elastic foundation; finite element method; pile; energy principle; lateral load.

Numerical Simulation of Breakwaters for Land Reclamation

2009 ◽  
Author(s):  
Jian-Min Zhang ◽  
Jianhong Zhang ◽  
Gang Wang ◽  
Yang Chen
Keyword(s):  
Land Reclamation ◽  
Southern China ◽  
Soft Soil ◽  
Three Dimensional ◽  
Marine Clay ◽  
Element Analysis ◽  
Dimensional Finite Element ◽  
Reclamation Project ◽  
The Moment ◽  
Three Dimensional Finite Element

This paper highlights some practical considerations of soil structure interactions in the design of the breakwater for a land reclamation project at Da Ya Bay, Southern China sea, through three-dimensional finite element analysis. A pile-breakwater-foundation system is evaluated during its construction and after construction has been completed. The maximum deflections and moments of the piles take place in the soft marine clay underneath the breakwater. The deformation of the soft soil imposes great impact on the slender pile. Based on the study, it is considered inadequate to solely increase the density and stiffness of the piles, as it will not effectively reduce the deformation of the foundation as well as the moment of the pile. On the contrary, the increased stiffness results in significant increase of the stresses in the pile. Consequently, the deformation of pile should be evaluated in terms of interactions between soil and pile. Improvement of the soft marine clay is also of great importance.

Analysis of Repaired Cracks With Bonded Composite Wrap in Pipes Under Bending

2016 ◽  
Vol 138 (6) ◽  
Author(s):  
Aida Achour ◽  
Abdulmohsen Albedah ◽  
Faycal Benyahia ◽  
Bel Abbes Bachir Bouiadjra ◽  
Djamel Ouinas
Keyword(s):  
Composite Materials ◽  
Fracture Criterion ◽  
Three Dimensional ◽  
Bending Moment ◽  
Element Analysis ◽  
Geometrical Properties ◽  
Bonded Composite ◽  
Dimensional Finite Element ◽  
Offshore Risers ◽  
Three Dimensional Finite Element

Composite materials have been used to structurally repair piping and other facilities for many years. However, the original use of composite materials was for repairing corroded pipelines where the intent was to restore strength to the damaged section of the pipeline. In addition to repairing corrosion, composite materials have successfully been used to repair dents, wrinkle bends, induction bends, and pipe fittings including elbows and tees as well as repair of offshore risers. In this study, the behavior of circumferential through cracks in repaired pipe with bonded composite wrap subjected to bending moment is investigated using three-dimensional finite-element analysis. The stress intensity factor (SIF) is utilized as a fracture criterion. The effects of the mechanical and geometrical properties of the adhesive on the variation of the SIF at the crack front were also analyzed. The obtained results show that the presence of the bonded composite repair significantly reduces the SIF, which can improve the residual lifespan of the pipe. Meanwhile, the SIF is also reduced as the elastic and the geometrical wrap properties are improved, particularly when the Young's modulus of the adhesive and the wrap thickness are increased.

3D Finite Element Analysis of Negative Skin Friction (NSF) Behaviors in Pile Groups with Cap

2013 ◽  
Vol 405-408 ◽  
pp. 390-395
Author(s):  
Li Nong Xia ◽  
Hai Tao Hu ◽  
Yun Dong Miao ◽  
Chang Bin Liao
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Neutral Point ◽  
Pile Groups ◽  
Element Analysis ◽  
Negative Skin Friction ◽  
Pile Cap ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element ◽  
Level Lowering

The pile-soil interactions are constrained by the pile cap in pile groups with cap, while mutually independent in pile groups without cap. The mechanism of changing of NSF in pile groups with cap are analyzed briefly. The NSF behaviors of pile groups with cap under the condition of groundwater level lowering are analyzed by three-dimensional finite element method. The analysis shows that the NSF of pile groups with cap is generally similar to that of a single pile: as the working loads on cap increasing, the neutral point moves up, additional settlement increases and the downdrag decreases, though there are differences between piles in different positions. The constraints of settlement of piles in various positions by the cap are significant when the working load is not large, so that the neutral point of piles are almost coincident. As the working load increasing, the deformation of the cap increases and the neutral point of piles become more various, lowest for the corner pile, second for the perimeter pile and highest for the interior pile. The NSF of each pile in pile groups with cap mobilizes differently along the depth. It is mobilized most fully for the corner pile, second for the perimeter pile and least for the interior pile.

Sign in / Sign up

Export Citation Format

Share Document