scholarly journals Numerical methodology for evaluation the combustion and emissions characteristics on WLTP in the light duty dual-fuel diesel vehicle

2021 ◽  
Author(s):  
Zbigniew Kneba ◽  
Denys Stepanenko ◽  
Jacek Rudnicki
Keyword(s):  
Internal Combustion Engines ◽  
Test Procedure ◽  
Real Life ◽  
Dual Fuel ◽  
Velocity Versus ◽  
Engine Operation ◽  
Time Profiles ◽  
General Terms ◽  
Vehicle Velocity ◽  
Harmful Emissions

The worldwide aim of reducing environmental impact from internal combustion engines bring more and more stringent emission regulations. In 2017 by EU has been adopted new harmonized test procedure called WLTP. In general terms this test was designed for determining the levels of harmful emissions and fuel consumption of traditional and hybrid cars. This procedure contains specific driving scenarios which representing real-life driving patterns. Test cycles contain vehicle velocity versus time profiles and directly in powertrain analysis on the test benches cannot be used. In order to back calculate drive cycles to engine rpm versus torque profiles a simple longitudinal vehicle dynamics method was used in this paper. Moreover, in order to determine most representative engine operation points duing WLTP a density based grid clustering method was implemented. The experimental part of the study focuses on the comparative evaluation of the effect of various diesel to LPG substitution ratios (0% LPG, 10% LPG, 20% LPG and 30% LPG) on combustion and emission characteristics of dual-fuel diesel engine.

scholarly journals Capturing Pressure Oscillations in Numerical Simulations of Internal Combustion Engines

2017 ◽  
Author(s):  
Sreenivasa Rao Gubba ◽  
Ravichandra S. Jupudi ◽  
Shyam Sundar Pasunurthi ◽  
Sameera D. Wijeyakulasuriya ◽  
Roy J. Primus ◽  
...  
Keyword(s):  
Internal Combustion Engines ◽  
Fuel Combustion ◽  
Dual Fuel ◽  
Cylinder Pressure ◽  
Pressure Oscillations ◽  
Engine Operation ◽  
Numerical Predictions ◽  
Medium Speed ◽  
Dual Fuel Combustion ◽  
The Mean

In an earlier publication [1] the authors compared numerical predictions of the mean cylinder pressure of diesel and dual-fuel combustion, to that of measured pressure data from a medium-speed, large-bore engine. In these earlier comparisons, measured data from a flush-mounted in-cylinder pressure transducer showed notable and repeatable pressure oscillations which were not evident in the mean cylinder pressure predictions from CFD. In this paper, the authors present a methodology for predicting and reporting the local cylinder pressure consistent with that of a measurement location. Such predictions for large-bore, medium-speed engine operation demonstrate pressure oscillations in accordance with those measured. The temporal occurrences of notable pressure oscillations were during the start of combustion and around the time of maximum cylinder pressure. With appropriate resolutions in time steps and mesh sizes, the local cell static pressure predicted for the transducer location showed oscillations in both diesel and dual-fuel combustion modes which agreed with those observed in the experimental data. Fast Fourier Transform (FFT) analysis on both experimental and calculated pressure traces revealed that the CFD predictions successfully captured both the amplitude and frequency range of the oscillations. Resolving propagating pressure waves with the smaller time steps and grid sizes necessary to achieve these results required a significant increase in computer resources.

DIESEL ENGINE OPERATION IN USE OF FUEL WITH ADDITIVES

2018 ◽  
pp. 18-24
Author(s):  
Petar Kazakov ◽  
Atanas Iliev ◽  
Emil Marinov
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Diesel Fuel ◽  
Internal Combustion Engines ◽  
Experimental Studies ◽  
Combustion Engines ◽  
Engine Operation ◽  
Factors Affecting ◽  
Operating Modes ◽  
Positive Effects

Over the decades, more attention has been paid to emissions from the means of transport and the use of different fuels and combustion fuels for the operation of internal combustion engines than on fuel consumption. This, in turn, enables research into products that are said to reduce fuel consumption. The report summarizes four studies of fuel-related innovation products. The studies covered by this report are conducted with diesel fuel and usually contain diesel fuel and three additives for it. Manufacturers of additives are based on already existing studies showing a 10-30% reduction in fuel consumption. Comparative experimental studies related to the use of commercially available diesel fuel with and without the use of additives have been performed in laboratory conditions. The studies were carried out on a stationary diesel engine СМД-17КН equipped with brake КИ1368В. Repeated results were recorded, but they did not confirm the significant positive effect of additives on specific fuel consumption. In some cases, the factors affecting errors in this type of research on the effectiveness of fuel additives for commercial purposes are considered. The reasons for the positive effects of such use of additives in certain engine operating modes are also clarified.

Measurement of cycle-resolved engine-out soot concentration from a diesel-pilot assisted natural gas direct-injection compression-ignition engine

2021 ◽  
pp. 146808742098626
Author(s):  
Pooyan Kheirkhah ◽  
Patrick Kirchen ◽  
Steven Rogak
Keyword(s):  
Response Time ◽  
Internal Combustion Engines ◽  
Fuel Injection ◽  
Exhaust System ◽  
Cycle Period ◽  
Scanning Mobility Particle Sizer ◽  
Compression Ignition Engine ◽  
Engine Operation ◽  
Exhaust Port ◽  
Exhaust Stream

Exhaust-stream particulate matter (PM) emission from combustion sources such as internal combustion engines are typically characterized with modest temporal resolutions; however, in-cylinder investigations have demonstrated significant variability and the importance of individual cycles in transient PM emissions. Here, using a Fast Exhaust Nephelometer (FEN), a methodology is developed for measuring the cycle-specific PM concentration at the exhaust port of a single-cylinder research engine. The measured FEN light-scattering is converted to cycle-resolved soot mass concentration ([Formula: see text]), and used to characterize the variability of engine-out soot emission. To validate this method, exhaust-port FEN measurements are compared with diluted gravimetric PM mass and scanning mobility particle sizer (SMPS) measurements, resulting in close agreements with an overall root-mean-square deviation of better than 30%. It is noted that when PM is sampled downstream in the exhaust system, the particles are larger by 50–70 nm due to coagulation. The response time of the FEN was characterized using a “skip-firing” scheme, by enabling and disabling the fuel injection during otherwise steady-state operation. The average response time due to sample transfer and mixing times is 55 ms, well below the engine cycle period (100 ms) for the considered engine speeds, thus suitable for single-cycle measurements carried out in this work. Utilizing the fast-response capability of the FEN, it is observed that cycle-specific gross indicated mean effective pressure (GIMEP) and [Formula: see text] are negatively correlated ([Formula: see text]: 0.2–0.7), implying that cycles with lower GIMEP emit more soot. The physical causes of this association deserve further investigation, but are expected to be caused by local fuel-air mixing effects. The averaged exhaust-port [Formula: see text] is similar to the diluted gravimetric measurements, but the cycle-to-cycle variations can only be detected with the FEN. The methodology developed here will be used in future investigations to characterize PM emissions during transient engine operation, and to enable exhaust-stream PM measurements for optical engine experiments.

Application of precision chronometric technologies for monitoring deviations in the internal combustion engine operation

2021 ◽  
Author(s):  
E.T. Plaksina ◽  
A.B. Syritsky ◽  
A.S. Komshin
Keyword(s):  
Internal Combustion Engine ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
The Arctic ◽  
Diagnostic Systems ◽  
Time Intervals ◽  
Angle Sensor ◽  
Engine Operation ◽  
Working Cycle

The article considers the main methods of internal combustion engine diagnostics. A method based on measuring the time intervals between the phases of the working cycle of the mechanism is described. An algorithm for measuring the time intervals from the formulation of the problem to the proof of the efficiency of this method on an internal combustion engine has been determined. The installation of the angle sensor on the crankshaft of the experimental bench engine VAZ 21126 is shown. The basis for the construction of a mathematical model of the crankshaft is presented and the main factors influencing its movement are identified. A criterion has been established according to which the misfire is determined most accurately. The results obtained can be used for developing diagnostic systems for internal combustion engines, as well as engines operating in extreme conditions, for example, beyond the Arctic Circle, on ships, etc.

Experimental Investigation of Effects of Split Diesel-Pilot Injection on Emissions From Ammonia-Diesel Dual Fuel Engine

2021 ◽  
Author(s):  
Yoichi Niki
Keyword(s):  
Diesel Fuel ◽  
Internal Combustion Engines ◽  
Ghg Emissions ◽  
High Reactivity ◽  
Dual Fuel ◽  
N2o Emissions ◽  
Injection Timing ◽  
Pilot Injection ◽  
Reduce Emissions ◽  
And Performance

Abstract NH3 has been investigated for its use as an alternative fuel including for use in internal combustion engines. In NH3 combustion, emissions of unburned NH3 with toxicity and N2O as a combustion product with high global warming potential (GWP) are important issues. However, few researchers have investigated NH3 and N2O emissions from NH3 assisted diesel engines operated using NH3–diesel dual fuel. We investigate a combustion strategy to reduce these emissions with a single-cylinder diesel engine mixed NH3 gas into the intake air. We found that an early diesel pilot injection reduced unburned NH3 and N2O emissions while HC and CO emissions increased. It was also reported that NH3 and diesel fuel work as low and high reactivity fuel for reactivity controlled compression ignition combustion (RCCI), respectively. Our previous study reports the aspects of RCCI on NH3–diesel dual fuel engine to some extent. The injection timing of diesel fuel and the quantity of NH3 govern the emissions and performance on RCCI combustion. These effects need to be investigated to manipulate the RCCI combustion and reduce emissions. This paper reports the efficiency and emissions for the diesel pilot injection timing sweep at various NH3 supply quantities and the effects of a split injection on the emissions and a combustion phase. In addition, we estimated the reduction in GHG emissions using a NH3–diesel dual fuel engine, which applied the early diesel pilot injection, compared with the diesel only operation, considering the N2O GWP.

scholarly journals Research on Fuel Efficiency and Emissions of Converted Diesel Engine with Conventional Fuel Injection System for Operation on Natural Gas

Energies ◽  
2019 ◽  
Vol 12 (12) ◽  
pp. 2413 ◽  
Author(s):  
Lebedevas ◽  
Pukalskas ◽  
Daukšys ◽  
Rimkus ◽  
Melaika ◽  
...  
Keyword(s):  
Energy Efficiency ◽  
Natural Gas ◽  
Fuel Injection ◽  
Injection System ◽  
Dual Fuel ◽  
Injection Timing ◽  
Fuel Injection System ◽  
Significant Deterioration ◽  
Engine Operation ◽  
Conventional Fuel

This paper presents a study on the energy efficiency and emissions of a converted high-revolution bore 79.5 mm/stroke 95 mm engine with a conventional fuel injection system for operation with dual fuel feed: diesel (D) and natural gas (NG). The part of NG energy increase in the dual fuel is related to a significant deterioration in energy efficiency (ηi), particularly when engine operation is in low load modes and was determined to be below 40% of maximum continuous rating. The effectiveness of the D injection timing optimisation was established in high engine load modes within the range of a co-combustion ratio of NG ≤ 0.4: with an increase in ηi, compared to D, the emissions of NOx+ HC decreased by 15% to 25%, while those of CO2 decreased by 8% to 16%; the six-fold CO emission increase, up to 6 g/kWh, was unregulated. By referencing the indicated process characteristics of the established NG phase elongation in the expansion stroke, the combustion time increase as well as the associated decrease in the cylinder excess air ratio (α) are possible reasons for the increase in the incomplete combustion product emission.

Model-based compressor surge avoidance algorithm for internal combustion engines utilizing cylinder deactivation during motoring conditions

2019 ◽  
pp. 146808741988347
Author(s):  
Alexander H Taylor ◽  
Troy E Odstrcil ◽  
Aswin K Ramesh ◽  
Gregory M Shaver ◽  
Edward Koeberlein ◽  
...  
Keyword(s):  
Internal Combustion Engines ◽  
Intake Manifold ◽  
Combustion Engines ◽  
Engine Exhaust ◽  
Engine Operation ◽  
Aftertreatment System ◽  
Cylinder Deactivation ◽  
Valve Motion ◽  
Compressor Surge ◽  
Intake Manifold Pressure

Cylinder deactivation is an efficient strategy for diesel engine exhaust aftertreatment thermal management. Temperatures in excess of 200 °C are necessary for peak NO x conversion efficiency of the aftertreatment system. However, during non-fired engine operation, known as motoring, conventional diesel engines pump low-temperature air through the aftertreatment system. One strategy to mitigate this is to deactivate valve motion during engine motoring. There is a specific condition where care must be taken to avoid compressor surge during the onset of valve deactivated motoring when following high load operation. This study proposes and validates an algorithm which (1) predicts the intake manifold pressure increase instigated while transitioning into cylinder deactivation during motoring, (2) estimates future mass air flow, and (3) avoids compressor surge by implementing staged cylinder deactivation during the onset of engine motoring operation.

On-board online evaluation of the charge density in internal combustion engines through electrical discharge characteristics

2019 ◽  
Vol 22 (1) ◽  
pp. 341-348
Author(s):  
Nir Druker ◽  
Gideon Goldwine ◽  
Eran Sher
Keyword(s):  
Charge Density ◽  
Internal Combustion Engines ◽  
Evaluation Method ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Ambient Conditions ◽  
Engine Operation ◽  
Cycle Basis ◽  
Spark Timing ◽  
Propulsion Unit

We propose here a new method to evaluate the mixture charge density inside the combustion chamber of an internal combustion engine. This is an important parameter that is needed to optimize the spark timing and the amount of fuel that is introduced to the cylinder at each cycle, thus optimizing the engine operation for higher power, lower brake-specific fuel consumption, or lower pollutants’ emission at any altitude/ambient conditions. The evaluation of the charge density is performed at each cycle (on a cycle-to-cycle basis) by using the voltage–current characteristics of the spark plug gap. This real-time evaluation method may save two of the present in-use temperature and pressure gages, thus considerably increasing the reliability of the propulsion unit. Owing to the expected higher system reliability and system simplicity, small unmanned aerial vehicles, as well as small automotive engines of various types, may significantly benefit from this proposed method. The method principles, rationale, and some preliminary results are presented.

Sign in / Sign up

Export Citation Format

Share Document