scholarly journals Use of zirconium phosphate system as a photocatalyst: Photobleaching of tolonium chloride

2008 ◽  
Vol 27 (2) ◽  
pp. 133 ◽  
Author(s):  
O. P. Panwar ◽  
Anil Kumar ◽  
Rameshwar Ameta ◽  
Suresh C. Ameta

Water pollution due to effluents from dyes and printing industries poses a serious problem for aquatic life. Photocatalysis has attracted the attention of chemists all over the world because it is an efficient and ecofriendly process to combat the problem of water pollution. Photocatalytic bleaching of tolonium chloride on zirconium phosphate was carried out in presence of light. The progress of the reaction was monitored spectrophotometrically, and it follows pseudo first order kinetics. The effect of variation of different parameters, like concentration of tolonium chloride, pH, amount of semiconductor and light intensity on the rate of bleaching, was also studied. A tentative mechanism for the photocatalytic bleaching of tolonium chloride has been proposed.

2011 ◽  
Vol 30 (2) ◽  
pp. 229 ◽  
Author(s):  
Shweta Sharma ◽  
Rakshit Ameta ◽  
R. K. Malkani ◽  
Suresh C. Ameta

Different methods have been adopted for the removal and degradation of dyes from effluents of textile, dyeing and printing industries. These methods have their own merits and drawbacks. In the present investigation, bismuth sulfide has been used as a photocatalyst for the degradation of rose Bengal. The effect of different parameters like the pH, concentration of dye solution, amount of semiconductor and light intensity on the rate of reaction has been investigated. The reaction follows pseudo-first order kinetics. The optimum conditions were obtained as: [rose Bengal] = 1.60·10–5 M; Bi2S3 = 0.10 g; pH = 8.5, and light intensity = 50.0 mW·cm–2. The rate constant was 4.68·10–5 sec–1. A mechanism has been proposed for the degradation of rose Bengal involving hydroxyl radicals.


2013 ◽  
Vol 15 (4) ◽  
pp. 551-559

<p>The effect of different operational parameters in UV/TiO2 process, such as initial dye concentration (20-50 mg l-1), light intensity (8-45 W m-2), pH (2.83-10.22), hydrogen peroxide concentration (100-500 mg l-1), temperature (21-45 ˚C) and photocatalyst concentration (150-900 mg l-1) were investigated on the decolorization of Acid Yellow 23 as a model compound from monoazo textile dyes. The apparent first-order rate constants (kap) were evaluated which confirms pseudo first-order kinetics. kap increased with the enhancement of pH, light intensity and temperature. A desired concentration found for hydrogen peroxide (400 mg l-1) and photocatalyst concentration (750 mg l-1). The SnO2 photocatalyst was not as effective as TiO2 but had the same desired concentration (750 mg l-1). Then TiO2+SnO2 suspensions (375+375 mg l-1) as photocatalysts were employed for decolorization at different solution thicknesses. The results showed that the coupled particles were not much different from single TiO2 system at the solution thickness of 4.5 cm in a batch reactor. But the coupled system was more effective when the solution thickness was reduced to 2.5 cm. Over 90% of decolorization occurs at the solution thickness of 1.1 cm after 30 min of irradiation while 90% decolorization takes place at the solution thickness of 4.5 cm after 100 min of irradiation.</p>


2020 ◽  
Vol 16 ◽  
Author(s):  
M. Alarjah

Background: Prodrugs principle is widely used to improve the pharmacological and pharmacokinetic properties of some active drugs. Much effort was made to develop metronidazole prodrugs to enhance antibacterial activity and or to improve pharmacokinetic properties of the molecule or to lower the adverse effects of metronidazole. Objective: In this work, the pharmacokinetic properties of some of monoterpenes and eugenol pro metronidazole molecules that were developed earlier were evaluated in-vitro. The kinetic hydrolysis rate constants and half-life time estimation of the new metronidazole derivatives were calculated using the validated RP-HPLC method. Method: Chromatographic analysis was done using Zorbbax Eclipse eXtra Dense Bonding (XDB)-C18 column of dimensions (250 mm, 4.6 mm, 5 μm), at ambient column temperature. The mobile phase was a mixture of sodium dihydrogen phosphate buffer of pH 4.5 and methanol in gradient elution, at 1ml/min flow rate. The method was fully validated according to the International Council for Harmonization (ICH) guidelines. The hydrolysis process carried out in an acidic buffer pH 1.2 and in an alkaline buffer pH 7.4 in a thermostatic bath at 37ºC. Results: The results followed pseudo-first-order kinetics. All metronidazole prodrugs were stable in the acidic pH, while they were hydrolysed in the alkaline buffer within a few hours (6-8 hr). The rate constant and half-life values were calculated, and their values were found to be 0.082- 0.117 hr-1 and 5.9- 8.5 hr., respectively. Conclusion: The developed method was accurate, sensitive, and selective for the prodrugs. For most of the prodrugs, the hydrolysis followed pseudo-first-order kinetics; the method might be utilised to conduct an in-vivo study for the metronidazole derivatives with monoterpenes and eugenol.


2021 ◽  
Vol 02 ◽  
Author(s):  
Emmanuel M. de la Fournière ◽  
Jorge M. Meichtry ◽  
Graciela S. Custo ◽  
Eduardo A. Gautier ◽  
Marta I. Litter

Background: Thiomersal (TM), a complex between 2-mercaptobenzoic acid (2-MBA) and ethylmercury (C2H5Hg+), is an antimicrobial preservative used in immunological, ophthalmic, cosmetic products, and vaccines. Objective: TM has been treated by UV/TiO2 photocatalysis in the presence or absence of oxygen at acidic pH. C2H5Hg+, 2-MBA, and 2-sulfobenzoic acid (2-SBA) were found as products. A 2-SBA photocatalytic treatment was undertaken to study sulfur evolution. Methods: Photocatalytic runs were performed using a UVA lamp (λmax = 352 nm), open to the air or under N2. A suspension of the corresponding TM or 2-SBA salt and TiO2 was prepared, and pH was adjusted. Suspensions were stirred in the dark for 30 min and then irradiated. TM, 2-MBA, 2-SBA, and C2H5Hg+ were quantified by HPLC, sulfur by TXRF, and the deposits on the photocatalyst were analyzed by chemical reactions. The mineralization degree was followed by TOC. Sulfate was determined using BaCl2 at 580 nm. Results: Photocatalytic destruction of TM and total C2H5Hg+ was complete under N2 and air, but TM degradation was much faster in air. The evolution of TM and the products followed a pseudo-first-order kinetics. Conclusion: TiO2-photocatalytic degradation is a suitable technique for the treatment of TM and its degradation products. In contrast to other organomercurial compounds, TM degradation is faster in the presence of O2, indicating that the oxidative mechanism is the preferred pathway. A significant TM mineralization (> 60%, NPOC and total S) was obtained. TM was more easily degraded than 2-SBA. Sulfate was the final product.


2021 ◽  
Vol 33 (10) ◽  
pp. 2251-2259
Author(s):  
Elizabeth Kuruvilla ◽  
C. Freeda Christy ◽  
A. Samson Nesaraj

Presently water pollution is the one of the major threats faced by living things all over the world. The main cause of water pollution is its effect on the life of aquatic animals. Organic, inorganic, microbial and other pollutants often mix with water bodies mainly due to human activities. Because of the presence of pollutants in water, the amount of dissolved oxygen level can be decreased which in turn affect the survival of aquatic life. The pollutant water may enter the agriculture fields and damage the plants extensively. The methods, such as, coagulation, adsorption, foam floating, electrodialysis, capacitive deionization, etc. are presently employed to treat the waste water. Among these methods, heterogeneous photocatalytic degradation is considered to be a good method because of its low cost and environmental friendliness. In this review, the decontamination of different kinds of organic, inorganic and microbial contaminants in water with different photocatalysts process is presented.


Author(s):  
Zhiliang Zhang ◽  
Jiaqi Lu ◽  
Bingqian Lv ◽  
Wei Liu ◽  
Shuyuan Shen ◽  
...  

The gas-liquid jet flow was proved to be capable of inducing chemical consequences which can lead to the decomposition of methylene blue (MB). The reaction process follows a pseudo-first-order kinetics....


1996 ◽  
Vol 314 (3) ◽  
pp. 985-991 ◽  
Author(s):  
Subrata ADAK ◽  
Abhijit MAZUMDER ◽  
Ranajit K. BANERJEE

The plausible role of arginine and tyrosine residues at the active site of horseradish peroxidase (HRP) in aromatic donor (guaiacol) oxidation was probed by chemical modification followed by characterization of the modified enzyme. The arginine-specific reagents phenylglyoxal (PGO), 2,3-butanedione and 1,2-cyclohexanedione all inactivated the enzyme, following pseudo-first-order kinetics with second-order rate constants of 24 M-1·min-1, 0.8 M-1·min-1 and 0.54 M-1·min-1 respectively. Modification with tetranitromethane, a tyrosine-specific reagent, also resulted in 50% loss of activity following pseudo-first-order kinetics with a second-order rate constant of 2.0 M-1·min-1. The substrate, H2O2, and electron donors such as I- and SCN- offered no protection against inactivation by both types of modifier, whereas the enzyme was completely protected by guaiacol or o-dianisidine, an aromatic electron donor (second substrate) oxidized by the enzyme. These studies indicate the involvement of arginine and tyrosine residues at the aromatic donor site of HRP. The guaiacol-protected phenylglyoxal-modified enzyme showed almost the same binding parameter (Kd) as the native enzyme, and a similar free energy change (∆G´) for the binding of the donor. Stoicheiometric studies with [7-14C]phenylglyoxal showed incorporation of 2 mol of phenylglyoxal per mol of enzyme, indicating modification of one arginine residue for complete inactivation. The difference absorption spectrum of the tetranitromethane-modified against the native enzyme showed a peak at 428 nm, characteristic of the nitrotyrosyl residue, that was abolished by treatment with sodium dithionite, indicating specific modification of a tyrosine residue. Inactivation stoicheiometry showed that modification of one tyrosine residue per enzyme caused 50% inactivation. Binding studies by optical difference spectroscopy indicated that the arginine-modified enzyme could not bind guaiacol at all, whereas the tyrosine-modified enzyme bound it with reduced affinity (Kd 35 mM compared with 10 mM for the native enzyme). Both the modified enzymes, however, retained the property of the formation of compound II (one-electron oxidation state higher than native ferriperoxidase) with H2O2, but reduction of compound II to native enzyme by guaiacol did not occur in the PGO-modified enzyme, owing to lack of binding. No non-specific change in protein structure due to modification was evident from circular dichroism studies. We therefore suggest that the active site of HRP for aromatic donor oxidation is composed of an arginine and an adjacent tyrosine residue, of which the former plays an obligatory role in aromatic donor binding whereas the latter residue plays a facilitatory role, presumably by hydrophobic interaction or hydrogen bonding.


1950 ◽  
Vol 33 (6) ◽  
pp. 703-722 ◽  
Author(s):  
C. W. Sheppard ◽  
W. R. Martin

The exchange of potassium between cells and plasma of heparinized human blood has been studied in vitro using the radioactive isotope K42. The changes in cell and plasma specific activity are characteristic of a simple two-compartment system. The mean of seven determinations of the exchange rate at 38°C. is 1.8 per cent of the cellular potassium per hour. The results indicate that at 38°C. the rate is relatively insensitive to oxygenation or reduction of the hemoglobin, and to 1200 r of gamma radiation. With varying temperature the rate follows pseudo first order kinetics with a Q10 of 2.35. Below 15°C. the rate of loss of potassium exceeds the rate of uptake.


1991 ◽  
Vol 278 (2) ◽  
pp. 595-599 ◽  
Author(s):  
N Hirano ◽  
T Ichiba ◽  
A Hachimori

Treatment of the inorganic pyrophosphatase from thermophilic bacterium PS-3 with diethyl pyrocarbonate resulted in the almost complete loss of its activity, which followed pseudo-first-order kinetics. The presence of Mg2+ prevented the inactivation. Enzyme inactivated with diethyl pyrocarbonate was re-activated by hydroxylamine. The inactivation parallelled the amount of modified histidine residue, and a plot of the activity remaining against the amount of modified histidine residue suggested that the modification of one of two histidine residues totally inactivated the enzyme. The site involved was found to be located in a single lysyl endopeptidase-digest peptide derived from the ethoxy[14C]carbonylated enzyme. Amino acid analysis and sequence analysis of the peptide revealed that it comprised residues 96-119 of the inorganic pyrophosphatase from thermophilic bacterium PS-3. These results, when compared with those reported for the Escherichia coli and yeast enzymes, imply that His-118 of the inorganic pyrophosphatase from thermophilic bacterium PS-3 is located near the Mg(2+)-binding site and thus affects the binding of Mg2+.


2012 ◽  
Vol 65 (11) ◽  
pp. 1970-1974 ◽  
Author(s):  
C. Y. Kuo ◽  
C. Y. Pai ◽  
C. H. Wu ◽  
M. Y. Jian

This study applies photo-Fenton and photo-Fenton-like systems to decolorize C.I. Reactive Red 2 (RR2). The oxidants were H2O2 and Na2S2O8; Fe2+, Fe3+, and Co2+ were used to activate these two oxidants. The effects of oxidant concentration (0.3–2 mmol/L) and temperature (25–55 °C) on decolorization efficiency of the photo-Fenton and photo-Fenton-like systems were determined. The decolorization rate constants (k) of RR2 in the tested systems are consistent with pseudo-first-order kinetics. The rate constant increased as oxidant concentration and temperature increased. Activation energies of RR2 decolorization in the UV/H2O2/Fe2+, UV/H2O2/Fe3+, UV/Na2S2O8/Fe2+ and UV/Na2S2O8/Fe3+ systems were 32.20, 39.54, 35.54, and 51.75 kJ/mol, respectively.


Sign in / Sign up

Export Citation Format

Share Document