scholarly journals Performance and Emissions of a Microturbine and Turbofan Powered by Alternative Fuels

2020 ◽  
Author(s):  
Radoslaw Przysowa ◽  
Bartosz Gawron ◽  
Tomasz Białecki ◽  
Anna Łęgowik ◽  
Jerzy Merkisz ◽  
...  
Keyword(s):  
Alternative Fuels ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Jet Engines ◽  
Gas Emissions ◽  
Used Cooking Oil ◽  
Performance And Emissions ◽  
Emissivity Model ◽  
Aircraft Performance ◽  
The Impact

Alternative fuels containing biocomponents produced in various technologies are introduced in aviation to reduce its carbon footprint but there is little data describing their impact on the performance and emissions of engines. The purpose of the work is to compare the performance and gas emissions produced from two different jet engines: the GTM-140 microturbine and the full-size DGEN380 turbofan, powered by blends of Jet A-1 and one of two biocomponents: 1) ATJ and 2) HEFA produced from used cooking oil (UCO) in various concentrations. The acquired data will be used to develop an engine emissivity model to predict gas emissions. Blends of the mineral fuel with synthetic components were prepared in various concentrations, and their physicochemical parameters were examined in the laboratory. Measurements of emissions from both engines were carried out in selected operating points using the Semtech DS gaseous analyzer and the EEPS spectrometer. The impact of tested blends on engine operating parameters is limited, and their use does not carry the risk of a significant decrease in aircraft performance or increase in fuel consumption. Increasing the content of biocomponents causes a noticeable rise in the emission of CO and slight increase for some other gasses (HC and NOx), which should not, however, worsen the working conditions of the ground personnel. This implies that there are no contraindications against using tested blends for fuelling gas-turbine engines.

scholarly journals Performance and Emissions of a Microturbine and Turbofan Powered by Alternative Fuels

Aerospace ◽  
2021 ◽  
Vol 8 (2) ◽  
pp. 25
Author(s):  
Radoslaw Przysowa ◽  
Bartosz Gawron ◽  
Tomasz Białecki ◽  
Anna Łęgowik ◽  
Jerzy Merkisz ◽  
...  
Keyword(s):  
Alternative Fuels ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Jet Engines ◽  
Gas Emissions ◽  
Used Cooking Oil ◽  
Performance And Emissions ◽  
Emissivity Model ◽  
Aircraft Performance ◽  
The Impact

Alternative fuels containing biocomponents produced in various technologies are introduced in aviation to reduce its carbon footprint but there is little data describing their impact on the performance and emissions of engines. The purpose of the work is to compare the performance and gas emissions produced from two different jet engines—the GTM-140 microturbine and the full-size DGEN380 turbofan, powered by blends of Jet A-1 and one of two biocomponents: (1) Alcohol-to-Jet (ATJ) and (2) Hydroprocessed Esters and Fatty Acids (HEFA) produced from used cooking oil (UCO) in various concentrations. The acquired data will be used to develop an engine emissivity model to predict gas emissions. Blends of the mineral fuel with synthetic components were prepared in various concentrations, and their physicochemical parameters were examined in the laboratory. Measurements of emissions from both engines were carried out in selected operating points using the Semtech DS gaseous analyzer and the EEPS spectrometer. The impact of tested blends on engine operating parameters is limited, and their use does not carry the risk of a significant decrease in aircraft performance or increase in fuel consumption. Increasing the content of biocomponents causes a noticeable rise in the emission of CO and slight increase for some other gasses (HC and NOx), which should not, however, worsen the working conditions of the ground personnel. This implies that there are no contraindications against using tested blends for fuelling gas-turbine engines.

scholarly journals The impact of physico-chemical properties of the jet fuel and biofuels on the characteristics of gas-turbine engines

2019 ◽  
Vol 22 (6) ◽  
pp. 8-16
Author(s):  
Sh. Ardeshiri
Keyword(s):  
Mathematical Model ◽  
Gas Turbine ◽  
Alternative Fuels ◽  
Gas Turbine Engine ◽  
Jet Fuel ◽  
Civil Aviation ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Turbine Engine ◽  
The Impact

The current development trend of global civil aviation is the growth of passenger and freight traffic, which entails the consumption of jet fuel. Under these conditions, increasing the efficiency of jet fuel used is of great importance. Global energy consumption is constantly growing, and, first of all, the question of diversification of oil resources arises, resources from which the bulk of motor fuels is produced. Other types of raw energy sources (natural gas, coal, bio-mass) currently account for only a small part. However, an analysis of the development of jet fuels indicates that work is underway to obtain these from other sources of raw materials, especially bio-fuels. Much attention is given to obtaining bio-fuels from renewable sources – such as algae. The issue of the mass transition of civil aviation to alternative fuels is complex and requires the solution of intricate technical as well as economic issues. One of these is the assessment of the impact of new fuels on GTE performance. It is important to give an objective and quick assessment of the use of various types of fuels on the main characteristics of the engine – i.e., throttle and high-speed characteristics. In this case, it is necessary to take into account chemical processes in the chemical composition of new types of fuel. To assess the effect of fuels on the characteristics of a gas turbine engine, it is proposed to use a mathematical model that would take into account the main characteristics of the fuel itself. Therefore, the work proposes a mathematical model for calculating the characteristics of a gas turbine engine taking into account changes in the properties of the fuel itself. A comparison is made of the percentage of a mixture of biofuels and JetA1 kerosene, as well as pure JetA1 and TC-1 kerosene. The calculations, according to the proposed model, are consistent with the obtained characteristics of a gas turbine engine in operation when using JetA1 and TC-1 kerosene. Especially valuable are the obtained characteristics of a gas turbine engine depending on a mixture of biofuel and kerosene. It was found that a mixture of biofuel and kerosene changes the physicochemical characteristics of fuel and affects the change in engine thrust and specific fuel consumption. It is shown that depending on the obtained physicochemical properties of a mixture of biofuel and kerosene, it is possible to increase the fuel efficiency and environmental friendliness of the gas turbine engines used.

scholarly journals Single-Coil Eddy Current Sensors and Their Application for Monitoring the Dangerous States of Gas-Turbine Engines

Sensors ◽  
2020 ◽  
Vol 20 (7) ◽  
pp. 2107 ◽  
Author(s):  
Sergey Borovik ◽  
Yuriy Sekisov
Keyword(s):  
Gas Turbine ◽  
Eddy Current ◽  
Natural Aging ◽  
Turbine Engines ◽  
Radial Clearance ◽  
Gas Turbine Engines ◽  
Structural Elements ◽  
Single Coil ◽  
The Impact ◽  
Blade Tips

The creation and exploitation of gas turbine engines (GTE) often involve two mutually exclusive tasks related to ensuring the highest reliability while achieving a good economic and environmental performance of the power plant. The value of the radial clearance between the blade tips of the compressor or turbine and the stator is a parameter that has a significant impact on the efficiency and safety of the GTE. However, the radial displacements that form tip clearances are only one of the components of the displacements made by GTE elements due to the action of power loads and thermal deformations during engines’ operation. The impact of loads in conjunction with natural aging is also the reason for the wear of the GTE’s structural elements (for example, bearing assemblies) and the loss of their mechanical strength. The article provides an overview of the methods and tools for monitoring the dangerous states of the GTE (blade tips clearances, impellers and shafts displacements, debris detecting in lubrication system) based on the single-coil eddy current sensor, which remains operational at the temperatures above 1200 °C. The examples of practical application of the systems with such sensors in bench tests of the GTE are given.

System Level Performance and Emissions Evaluation of Renewable Fuels for Jet Engines

2014 ◽  
Author(s):  
Kadambari Lokesh ◽  
Vishal Sethi ◽  
Theoklis Nikolaidis ◽  
Devaiah Karumbaiah
Keyword(s):  
Engine Performance ◽  
Operating Conditions ◽  
System Level ◽  
Civil Aviation ◽  
Jet Engines ◽  
Stirred Reactor ◽  
Fuel Burn ◽  
Performance And Emissions ◽  
Aircraft Performance ◽  
Level Performance

Incessant demand for fossil derived energy and the resulting environmental impact has urged the renewable energy sector to conceive one of the most anticipated sustainable, alternative “drop-in” fuels for jet engines, called as, Bio-Synthetic Paraffinic Kerosene (Bio-SPKs). Second (Camelina SPK & Jatropha SPK and third generation (Microalgae SPK) advanced biofuels have been chosen to analyse their influence on the behaviour of a jet engine through numerical modelling and simulation procedures. The thermodynamic influence of each of the biofuels on the gas turbine performance extended to aircraft performance over a user-defined trajectory (with chosen engine/airframe configuration) have been reported in this paper. Initially, the behaviour of twin-shaft turbofan engine operated with 100% Bio-SPKs at varying operating conditions. This evaluation is conducted from the underpinning phase of adopting the chemical composition of Bio-SPKs towards an elaborate and careful prediction of fluid thermodynamics properties (FTPs). The engine performance was primarily estimated in terms of fuel consumption which steers the fiscal and environmental scenarios in civil aviation. Alternative fuel combustion was virtually simulated through stirred-reactor approach using a validated combustor model. The system-level emissions (CO2 and NOx) have been numerically quantified and reported as follows: the modelled aircraft operating with Bio-SPKs exhibited fuel economy (mission fuel burn) by an avg. of 2.4% relative to that of baseline (Jet Kerosene). LTO-NOx for the user-defined trajectory decreased by 7–7.8% and by 15–18% considering the entire mission. Additionally, this study reasonably qualitatively explores the benefits and issues associated with Bio-SPKs.

The Potential Impact of Future Fuels on Small Gas Turbine Engines

1982 ◽  
Author(s):  
J. A. Saintsbury ◽  
P. Sampath
Keyword(s):  
Gas Turbine ◽  
Operating Experience ◽  
Gas Turbine Engine ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Turbine Engine ◽  
The Future ◽  
Potential Impact ◽  
The Impact ◽  
Whitney Aircraft

The impact of potential aviation gas turbine fuels available in the near to midterm, is reviewed with particular reference to the small aviation gas turbine engine. The future course of gas turbine combustion R&D, and the probable need for compromise in fuels and engine technology, is also discussed. Operating experience to date on Pratt & Whitney Aircraft of Canada PT6 engines, with fuels not currently considered of aviation quality, is reported.

scholarly journals Some Aerodynamic Problems of Aircraft Engines: Fifty Years After -The 2007 IGTI Scholar Lecture-

2009 ◽  
Vol 131 (3) ◽  
Author(s):  
Edward M. Greitzer
Keyword(s):  
Gas Turbine ◽  
Collaborative Research ◽  
Research Process ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Aircraft Engines ◽  
Jet Engines ◽  
Organizational Boundaries ◽  
Turbine Performance ◽  
Single Discipline

Problems of high technological interest, for example the development of gas turbine engines, span disciplinary, and often organizational, boundaries. Although collaboration is critical in advancing the technology, it has been less a factor in gas turbine research. In this paper it is proposed that step changes in gas turbine performance can emerge from collaborative research endeavors that involve the development of integrated teams with the needed range of skills. Such teams are an important aspect in product development, but they are less familiar and less subscribed to in the research community. The case histories of two projects are given to illustrate the point: the development of the concept of “smart jet engines” and the Silent Aircraft Initiative. In addition to providing a capability to attack multidisciplinary problems, the way in which collaboration can enhance the research process within a single discipline is also discussed.

The Interaction Between Mistuning and Friction in the Forced Response of Bladed Disk Assemblies

1985 ◽  
Vol 107 (1) ◽  
pp. 205-211 ◽  
Author(s):  
J. H. Griffin ◽  
A. Sinha
Keyword(s):  
Gas Turbine ◽  
Turbine Blades ◽  
Forced Response ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Resonant Response ◽  
Friction Dampers ◽  
Bladed Disk ◽  
The Impact ◽  
Slip Force

This paper summarizes the results of an investigation to establish the impact of mistuning on the performance and design of blade-to-blade friction dampers of the type used to control the resonant response of turbine blades in gas turbine engines. In addition, it discusses the importance of friction slip force variations on the dynamic response of shrouded fan blades.

scholarly journals Generalized High Speed Simulation of Gas Turbine Engines

1990 ◽  
Author(s):  
Nanahisa Sugiyama
Keyword(s):  
Real Time ◽  
Gas Turbine ◽  
Gas Turbines ◽  
High Speed ◽  
Power Plants ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Jet Engines ◽  
Industrial Gas Turbine ◽  
High Degree

This paper describes a real-time or faster-than-real-time simulation of gas turbine engines, using an ultra high speed, multi-processor digital computer, designated the AD100. It is shown that the frame time is reduced significantly without any loss of fidelity of a simulation. The simulation program is aimed at a high degree of flexibility to allow changes in engine configuration. This makes it possible to simulate various types of gas turbine engines, including jet engines, gas turbines for vehicles and power plants, in real-time. Some simulation results for an intercooled-reheat type industrial gas turbine are shown.

Semi-Closed Gas Turbine Cycles: An Ecological Solution

2001 ◽  
Author(s):  
A. L. Laganelli ◽  
C. Rodgers ◽  
W. E. Lear ◽  
P. L. Meitner
Keyword(s):  
Global Warming ◽  
Greenhouse Gases ◽  
Gas Turbine ◽  
Fossil Fuels ◽  
High Efficiency ◽  
Anthropogenic Heat ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Closed Cycle ◽  
The Impact

The impact on global warming of transportation and the infrastructure that supports it has been investigated over several decades. Anthropogenic heat and the generation of greenhouse gases from burning of fossil fuels and are major contributors to the warming process. An approach to mitigate these effects is discussed that considers semi-closed cycle gas turbine engines as a practical approach to slowing the release of greenhouse gases. Semi-closed cycle gas turbine engines have an inherent capability to reduce all regulated emissions while maintaining high efficiency, which in turn reduces CO2 emissions. With emerging technology development that includes higher component efficiencies, high temperature material development, improved control devices, and advanced combustor designs, aided by computational fluid dynamics, semi-closed cycle engines appear to have the potential to mitigate global warming with little economic or infrastructural impact. A specific semi-closed engine type is described, the high pressure recuperated turbine engine (HPRTE), along with the inherent mechanisms for control of NOx, CO, unburned hydrocarbons, and particulates. Results from a breadboard demonstration of the HPRTE are discussed, as well as emerging technologies which benefit this type of engine.

Problems and Use of the Scaling Factors in the Numerical Simulation of Jet Engines

1990 ◽  
Author(s):  
G. Torella
Keyword(s):  
Numerical Simulation ◽  
Trend Analysis ◽  
Gas Turbine ◽  
Engine Performance ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Jet Engines ◽  
Scaling Factors ◽  
Operational Life

The possibility of the use of scaling factors in the calculations and in the simulation of gas turbine engines have been considered. Application of this technique to the simulation of trend analysis, the evaluation of the component maps shifting during the operational life of the engine and the calculation of matrices of influence have been presented. Moreover, some problems related to the use of scaling factors have been studied and their effects on the engine performance have been presented.

Sign in / Sign up

Export Citation Format

Share Document