Technology Focus: Unconventional and Tight Reservoirs (July 2021)

2021 ◽  
Vol 73 (07) ◽  
pp. 57-57
Author(s):  
Leonard Kalfayan
Keyword(s):  
Oil And Gas ◽  
Gas Production ◽  
Alternative Methods ◽  
Gas Wells ◽  
Gas Reservoirs ◽  
Liquid Loading ◽  
Well Production ◽  
Tight Carbonate ◽  
Water Blocking ◽  
Tight Reservoirs

As unconventional oil and gas fields mature, operators and service providers are looking toward, and collaborating on, creative and alternative methods for enhancing production from existing wells, especially in the absence of, or at least the reduction of, new well activity. While oil and gas price environments remain uncertain, recent price-improvement trends are supporting greater field testing and implementation of innovative applications, albeit with caution and with cost savings in mind. Not only is cost-effectiveness a requirement, but cost-reducing applications and solutions can be, too. Of particular interest are applications addressing challenging well-production needs such as reducing or eliminating liquid loading in gas wells; restimulating existing, underperforming wells, including as an alternative to new well drilling and completion; and remediating water blocking and condensate buildup, both of which can impair production from gas wells severely. The three papers featured this month represent a variety of applications relevant to these particular well-production needs. The first paper presents a technology and method for liquid removal to improve gas production and reserves recovery in unconventional, liquid-rich reservoirs using subsurface wet-gas compression. Liquid loading, a recurring issue downhole, can severely reduce gas production and be costly to remediate repeatedly, which can be required. This paper discusses the full technology application process and the supportive results of the first field trial conducted in an unconventional shale gas well. The second paper discusses the application of the fishbone stimulation system and technique in a tight carbonate oil-bearing formation. Fishbone stimulation has been around for several years now, but its best applications and potential have not necessarily been fully understood in the well-stimulation community. This paper summarizes a successful pilot application resulting in a multifold increase in oil-production rate and walks the reader through the details of the pilot candidate selection, completion design, operational challenges, and lessons learned. The third paper introduces and proposes a chemical treatment to alleviate phase trapping in tight carbonate gas reservoirs. Phase trapping can be in the form of water blocking or increasing condensate buildup from near the wellbore and extending deeper into the formation over time. Both can reduce relative permeability to gas severely. Water blocks can be a one-time occurrence from drilling, completion, workover, or stimulation operations and can often be treated effectively with solvent plus proper additive solutions. Similar treatments for condensate banking in gas wells, however, can provide only temporary alleviation, if they are even effective. This paper proposes a technique for longer-term remediation of phase trapping in tight carbonate gas reservoirs using a unique, slowly reactive fluid system. Recommended additional reading at OnePetro: www.onepetro.org. SPE 200345 - Insights Into Field Application of Enhanced-Oil-Recovery Techniques From Modeling of Tight Reservoirs With Complex High-Density Fracture Network by Geng Niu, CGG, et al. SPE 201413 - Diagnostic Fracture Injection Test Analysis and Simulation: A Utica Shale Field Study by Jeffery Hildebrand, The University of Texas at Austin, et al.

Optimizing Tubing and Liner Completion Design to Improve Gas Production from Existing Wells: Case Study for ADNOC Onshore Field Abu Dhabi, UAE

2021 ◽  
Author(s):  
Magdy Farouk Fathalla ◽  
Mariam Ahmed Al Hosani ◽  
Ihab Nabil Mohamed ◽  
Ahmed Mohamed Al Bairaq ◽  
Djamal Kherroubi ◽  
...  
Keyword(s):  
Gas Production ◽  
Base Case ◽  
Gas Wells ◽  
Production Rates ◽  
Liquid Loading ◽  
Gas Field ◽  
Well Production ◽  
Well Completion ◽  
The Impact

Abstract An onshore gas field contains several gas wells which have low–intermittent production rates. The poor production has been attributed to liquid loading issue in the wellbore. This study will investigate the impact of optimizing the tubing and liner completion design to improve the gas production rates from the wells. Numerous sensitivity runs are carried out with varying tubing and liner dimensions, to identity optimal downhole completions design. The study begins by identifying weak wells having severe gas production problems. Once the weak wells have been identified, wellbore schematics for those wells are studied. Simulation runs are performed with the current downhole completion design and this will be used as the base case. Several completion designs are considered to minimize the effect of liquid loading in the wells; these include reducing the tubing diameter but keeping the existing liner diameter the same, keeping the original tubing diameter the same but only reducing the liner diameter, extending the tubing to the Total Depth (TD) while keeping the original tubing diameter, and extending a reduced diameter tubing string to the TD. The primary cause of the liquid loading seems to be the reduced velocity of the incoming gas from the reservoir as it flows through the wellbore. A simulation study was performed using the various completion designs to optimize the well completion and achieve higher gas velocities in the weak wells. The results of the study showed significant improvement in gas production rates when the tubing diameter and liner diameter were reduced, providing further evidence that increased velocity of the incoming fluids due to restricted flow led to less liquid loading. The paper demonstrates the impact of downhole completion design on the productivity of the gas wells. The study shows that revisiting the existing completion designs and optimizing them using commercial simulators can lead to significant improvement in well production rates. It is also noted that restricting the flow near the sand face increases the velocity of the incoming fluid and reduces liquid loading in the wells.

scholarly journals Tight carbonate gas well deliverability evaluation and reasonable production proration analysis

2021 ◽  
Author(s):  
Jiang Li ◽  
Xianchao Chen ◽  
Ping Gao ◽  
Jingchao Zhou
Keyword(s):  
Numerical Model ◽  
Stress Sensitivity ◽  
Gas Production ◽  
Productivity Index ◽  
Dual Porosity ◽  
Gas Reservoirs ◽  
Gas Well ◽  
Well Production ◽  
Tight Carbonate ◽  
Single Well

AbstractIt is very important to accurately predict the gas well productivity and reasonably allocate the gas production at the early development stage of gas reservoirs. However, both the non-Darcy and stress sensitivity effects have not been investigated in dual-porosity model of tight carbonate gas reservoirs. This paper proposed a new dual-porosity binomial deliverability model and single-well production proration numerical model, which consider the effects of non-Darcy and stress sensitivity. The field gas well deliverability tests data validated the accuracy of the new analytical model, which is a very helpful deliverability method when lacking deliverability test. A geological model was built on the results of the well log, well testing, and well production analysis. Then, a reasonable production proration analysis was conducted based on history matched single-well numerical model. The gas productivity index curve and production–prediction of MX22 several simulation cases were adopted to analyze the reasonable production proration. The results indicate that 1/6 may be suitable for high productivity gas well proration. In addition, the absolute open flow rate from the numerical simulation is higher than that from the new deliverability equation, which also shows that the pressure transient analysis sometimes has some deviation in formation property prediction. It is suggested comprehensively utilizing the analytical binomial model and the single-well numerical model in tight carbonate gas well deliverability evaluation.

Chemical Deliquification of Unconventional Gas Wells

2014 ◽  
Author(s):  
K.. Francis-LaCroix ◽  
D.. Seetaram
Keyword(s):  
Natural Gas ◽  
Best Practice ◽  
Oil And Gas ◽  
Large Deviation ◽  
Cost Effective ◽  
Gas Production ◽  
Lessons Learned ◽  
Offshore Platforms ◽  
Gas Wells ◽  
Current Production

Abstract Trinidad and Tobago offshore platforms have been producing oil and natural gas for over a century. Current production of over 1500 Bcf of natural gas per year (Administration, 2013) is due to extensive reserves in oil and gas. More than eighteen of these wells are high-producing wells, producing in excess of 150 MMcf per day. Due to their large production rates, these wells utilize unconventionally large tubulars 5- and 7-in. Furthermore, as is inherent with producing gas, there are many challenges with the production. One major challenge occurs when wells become liquid loaded. As gas wells age, they produce more liquids, namely brine and condensate. Depending on flow conditions, the produced liquids can accumulate and induce a hydrostatic head pressure that is too high to be overcome by the flowing gas rates. Applying surfactants that generate foam can facilitate the unloading of these wells and restore gas production. Although the foaming process is very cost effective, its application to high-producing gas wells in Trinidad has always been problematic for the following reasons: Some of these producers are horizontal wells, or wells with large deviation angles.They were completed without pre-installed capillary strings.They are completed with large tubing diameters (5.75 in., 7 in.). Recognizing that the above three factors posed challenges to successful foam applications, major emphasis and research was directed toward this endeavor to realize the buried revenue, i.e., the recovery of the well's potential to produce natural gas. This research can also lead to the application of learnings from the first success to develop treatment for additional wells, which translates to a revenue boost to the client and the Trinidad economy. Successful treatments can also be used as correlations to establish an industry best practice for the treatment of similarly completed wells. This paper will highlight the successes realized from the treatment of three wells. It will also highlight the anomalies encountered during the treatment process, as well as the lessons learned from this treatment.

scholarly journals The Key Factors That Determine the Economically Viable, Horizontal Hydrofractured Gas Wells in Mudrocks

Energies ◽  
2020 ◽  
Vol 13 (9) ◽  
pp. 2348 ◽  
Author(s):  
Syed Haider ◽  
Wardana Saputra ◽  
Tadeusz Patzek
Keyword(s):  
Gas Flow ◽  
Horizontal Well ◽  
Source Term ◽  
Organic Matrix ◽  
Fracture Network ◽  
Gas Production ◽  
Fracture Permeability ◽  
Gas Wells ◽  
Stimulated Reservoir Volume ◽  
Well Production

We assemble a multiscale physical model of gas production in a mudrock (shale). We then tested our model on 45 horizontal gas wells in the Barnett with 12–15 years on production. When properly used, our model may enable shale companies to gain operational insights into how to complete a particular well in a particular shale. Macrofractures, microfractures, and nanopores form a multiscale system that controls gas flow in mudrocks. Near a horizontal well, hydraulic fracturing creates fractures at many scales and increases permeability of the source rock. We model the physical properties of the fracture network embedded in the Stimulated Reservoir Volume (SRV) with a fractal of dimension D < 2 . This fracture network interacts with the poorly connected nanopores in the organic matrix that are the source of almost all produced gas. In the practically impermeable mudrock, the known volumes of fracturing water and proppant must create an equal volume of fractures at all scales. Therefore, the surface area and the number of macrofractures created after hydrofracturing are constrained by the volume of injected water and proppant. The coupling between the fracture network and the organic matrix controls gas production from a horizontal well. The fracture permeability, k f , and the microscale source term, s, affect this coupling, thus controlling the reservoir pressure decline and mass transfer from the nanopore network to the fractures. Particular values of k f and s are determined by numerically fitting well production data with an optimization algorithm. The relationship between k f and s is somewhat hyperbolic and defines the type of fracture system created after hydrofracturing. The extremes of this relationship create two end-members of the fracture systems. A small value of the ratio k f / s causes faster production decline because of the high microscale source term, s. The effective fracture permeability is lower, but gas flow through the matrix to fractures is efficient, thus nullifying the negative effect of the smaller k f . For the high values of k f / s , production decline is slower. In summary, the fracture network permeability at the macroscale and the microscale source term control production rate of shale wells. The best quality wells have good, but not too good, macroscale connectivity.

Well Completion for Effective Deliquification of Natural Gas Wells

2011 ◽  
Vol 134 (1) ◽  
Author(s):  
John Yilin Wang
Keyword(s):  
Natural Gas ◽  
Operating Cost ◽  
Gas Production ◽  
Gas Wells ◽  
Liquid Loading ◽  
Gas Recovery ◽  
Well Completion ◽  
Reservoir Permeability ◽  
Gas Fields ◽  
Gas Lift

Liquid loading has been a problem in natural gas wells for several decades. With gas fields becoming mature and gas production rates dropping below the critical rate, deliquification becomes more and more critical for continuous productivity and profitability of gas wells. Current methods for solving liquid loading in the wellbore include plunger lift, velocity string, surfactant, foam, well cycling, pumps, compression, swabbing, and gas lift. All these methods are to optimize the lifting of liquid up to surface, which increases the operating cost, onshore, and offshore. However, the near-wellbore liquid loading is critical but not well understood. Through numerical reservoir simulation studies, effect of liquid loading on gas productivity and recovery has been quantified in two aspects: backup pressure and near-wellbore liquid blocking by considering variable reservoir permeability, reservoir pressure, formation thickness, liquid production rate, and geology. Based on the new knowledge, we have developed well completion methods for effective deliquifications. These lead to better field operations and increased ultimate gas recovery.

Analysis of Fractured Sections in Shale Gas Wells Based on PCA - Logistic Regression Model

2020 ◽  
Vol 980 ◽  
pp. 483-492
Author(s):  
Lei Ji ◽  
Ju Hua Li ◽  
Guan Qun Li ◽  
Jia Lin Xiao ◽  
Sean Unrau
Keyword(s):  
Logistic Regression ◽  
Shale Gas ◽  
Logistic Regression Model ◽  
Gas Production ◽  
Gas Wells ◽  
Gas Reservoirs ◽  
Discriminant Model ◽  
Economic Exploitation ◽  
High Production ◽  
Pca Algorithm

In order to optimize the layout and economic exploitation of horizontal fracturing wells and completion in shale gas reservoirs, we propose a model for evaluating shale gas fractured sections based on an improved principle component analysis (PCA) algorithm with logistic regression. The 229 gas production sections in 22 fractured shale gas wells in the main block of the Fuling Shale Development Demonstration Zone were selected, and PCA is used for dimensionalite reduction. According to the PCA results, 6 key parameters are chosen to determine the productivity of fractured wells. Taking the probability distribution of high production after fracturing as the research objective, a logistic regression discriminant model was constructed using the dichotomy method. The prediction results show that the model has 82.1% accuracy and is reliable. The model can be used to classify and gas wells to be fractured, and it provides guiding significance for reasonable optimization of well sections in the area selected for fracturing.

Liquid loading in wellbores and its effect on cleanup period and well productivity in tight gas sand reservoirs

2010 ◽  
Vol 50 (1) ◽  
pp. 559
Author(s):  
Hassan Bahrami ◽  
M Reza Rezaee ◽  
Vamegh Rasouli ◽  
Armin Hosseinian
Keyword(s):  
Numerical Simulation ◽  
Gas Production ◽  
Production Performance ◽  
Tight Gas ◽  
Gas Reservoirs ◽  
Liquid Loading ◽  
Performance Modelling ◽  
Well Productivity ◽  
Tight Gas Reservoirs ◽  
Tight Gas Reservoir

Tight gas reservoirs normally have production problems due to very low matrix permeability and significant damage during well drilling, completion, stimulation and production. Therefore they might not flow gas to surface at optimum rates without advanced production improvement techniques. After well stimulation and fracturing operations, invaded liquids such as filtrate will flow from the reservoir into the wellbore, as gas is produced during well cleanup. In addition, there might be production of condensate with gas. The produced liquids when loaded and re-circulated downhole in wellbores, can significantly reduce the gas production rate and well productivity in tight gas formations. This paper presents assessments of tight gas reservoir productivity issues related to liquid loading in wellbores using numerical simulation of multiphase flow in deviated and horizontal wells. A field example of production logging in a horizontal well is used to verify reliability of the numerical simulation model outputs. Well production performance modelling is also performed to quantitatively evaluate water loading in a typical tight gas well, and test the water unloading techniques that can improve the well productivity. The results indicate the effect of downhole liquid loading on well productivity in tight gas reservoirs. It also shows how well cleanup is sped up with the improved well productivity when downhole circulating liquids are lifted using the proposed methods.

The Need to Understand the Dynamic Interaction Between Wellbore and Reservoir in Liquid Loaded Gas Wells

2008 ◽  
Author(s):  
Fouad A. Solomon ◽  
Gioia Falcone ◽  
Catalin Teodoriu
Keyword(s):  
Oil And Gas ◽  
Transient Flow ◽  
Oil And Gas Industry ◽  
Dynamic Interaction ◽  
Back Pressure ◽  
Pressure Effects ◽  
Gas Wells ◽  
Liquid Loading ◽  
Dynamic Interactions ◽  
Model Liquid

Liquid loading in gas wells is a phenomenon where the liquid content of the well is sufficient to create a back pressure (usually dominated by gravitational pressure changes) which restricts, and in some cases even stops, the flow of gas from the reservoir. Liquid loading is an all too common problem in mature gas fields around the world. It is estimated that in the U.S.A. alone, at least 90% of the producing gas wells are operating in liquid loading regime. The phenomenon is more detrimental in tight wells than in prolific wells and it poses a serious problem in subsea tie-backs, where back pressure effects through the risers and the flowlines may have an important role. Such is the importance of liquid loading; the oil and gas industry has devoted a lot of attention to the alleviation of the problem using various measures. However, the fundamental understanding of the associated phenomena is still surprisingly weak. This applies not only to the flows in the wells, but also to how these flows interact with those in the reservoir. It is this latter dynamic interaction that has received the least attention by the industry. Reliable predictive models to link the well dynamics with the intermittent response of a reservoir, that is typical of liquid loading in gas wells, remain unavailable. This paper introduces the complexity of liquid loading and critically reviews recent attempts to model liquid loading and the dynamic interactions between reservoir and wellbore. The paper then illustrates the need for a better understanding of the transient flow phenomena taking place in the near-wellbore region of the reservoir. This includes re-injection of the heavier phase, a phenomenon that has yet to be proven by fluid mechanics.

scholarly journals An experimental study of liquid unloading in the curve section of horizontal gas wells

2021 ◽  
Vol 76 ◽  
pp. 69
Author(s):  
Shuzhe Shi ◽  
Guoqing Han ◽  
Bohong Wu ◽  
Kangtai Xu ◽  
Zhun Li ◽  
...  
Keyword(s):  
Experimental Data ◽  
Poor Performance ◽  
Gas Production ◽  
Gas Velocity ◽  
Gas Wells ◽  
Liquid Loading ◽  
Curved Pipes ◽  
Comparison Results ◽  
Calculation Results ◽  
Superficial Gas Velocity

Liquid unloading is a very common and important issue in horizontal gas wells, and the presence of curve sections increases the complexity of the phenomenon and its study. Liquid loading in a gas well will sharply reduce production, therefore, the liquid-unloading onset of different curved pipes is essential to gas production. In this work, liquid-unloading onset experiments were conducted in curved pipes with different curvatures. Then, the critical gas velocity VsgCR can be determined according to the measured pressure gradients, liquid holdup, and liquid film reversal. This work analyzes the factors which will lead to the liquid unloading and explores the trend of the pipe curvature’s influence on the liquid unloading under laboratory conditions. The experimental results show that the critical gas velocity rises with the increase of pipe curvature, the increase is mainly due to the centrifugal force. The present work also compares the predicted results of the OLGA model and Beggs–Brill model with experimental data. The comparison results indicate that both models fit relatively well to the experimental data at the low superficial gas velocity, and both models have poor performance at high superficial gas velocity. The OLGA model fits the experimental data better than the Beggs–Brill model at high superficial gas velocity. The error analysis shows that most of the predicted data is not in good agreement with experimental data. Some errors between experimental data and calculation results are out of the range of 50%.

MASSIVE HYDRAULIC FRACTURE STIMULATION OF EARLY PERMIAN GAS RESERVOIRS, BIG LAKE FIELD, COOPER BASIN

1984 ◽  
Vol 24 (1) ◽  
pp. 180
Author(s):  
D. J. Stanley ◽  
G. Halliday
Keyword(s):  
Hydraulic Fracture ◽  
Joint Venture ◽  
Oil And Gas ◽  
Gas Production ◽  
Tight Gas ◽  
Gas Reservoirs ◽  
Potential Resource ◽  
Primary Porosity ◽  
Initial Results ◽  
Cooper Basin

In 1981, South Australian Oil and Gas Corporation Pty Ltd commenced a project to apply Massive Hydraulic Fracture (MHF) technology to the tight gas reservoirs of the Tirrawarra and Patchawarra Formations of the Big Lake Field. Four wells had defined the potential at depths of 8500-10 000 ft (2500-3000 m) in the early 1970s but early attempts to stimulate gas production were unsuccessful.The Tirrawarra Sandstone, as a massive unit of 120-200 ft (35-60 m) thickness, was a prime candidate. The Patchawarra sandstones, ranging up to 40 ft (12 m) thick and interbedded with shales and coals, presented a more difficult problem.Petrologic analysis disclosed quartz sandstones in which the pore system consists mainly of large irregularly shaped dissolution pores. Diagenesis has destroyed primary porosity and precipitated authigenic illite, illite-smectite, kaolinite and siderite. The gas contains 32 per cent CO2 and is very dry. Temperatures are close to 400°F (200°C). The formations are overpressured.The project has drilled two wells, Big Lake 26 and 27, and applied two MHF treatments in Big Lake 26. One further MHF remains to be done in Big Lake 27. Each MHF treatment has been tailored to the particular petrologic, reservoir, stratigraphic, pressure and temperature conditions of that zone. The tailoring of MHF design has been further refined by running a 'mini-frac' with 10 000 gal (45 000 L) of fluid. MHF designs have involved up to 620 000 lb (280 000 kg) of sand, 60 000 lb (27 000 kg) of sintered bauxite and 300 000 gal (1350 kL) of gel. Having management on-site to react to aberrations and vary the design has been important in operations.One Tlrrawarra Sandstone MHF has been unsuccessful (as predicted) and the other, on initial results, appears highly successful. The Patchawarra Formation MHF speared off into a coal but appears moderately successful. Long-term flow tests will provide definitive results.Encouraged by these initial results, the Joint Venture Partners have drilled two further wells in the Big Lake Field which await MHF treatment. The gas-in-place is estimated at about 1.5 trillion cubic feet (42.5 billion cubic metres). Three other tight gas prospects of similar size, Burley, McLeod and Kirby, have been identified. The size of this potential resource provides a strong incentive to attempt to make MHF treatments economically viable in the Cooper Basin.

Sign in / Sign up

Export Citation Format

Share Document