Evaluation of Polymer Flooding Efficiency at Brownfield Development Stage of Giant Kalamkas Oilfield, Western Kazakhstan (Russian)

2018 ◽  
Author(s):  
Marat Sagyndikov ◽  
Bolat Mukhambetov ◽  
Yermek Orynbasar ◽  
Aslanbek Nurbulatov ◽  
Sanat Aidarbayev
2018 ◽  
Author(s):  
Marat Sagyndikov ◽  
Bolat Mukhambetov ◽  
Yermek Orynbasar ◽  
Aslanbek Nurbulatov ◽  
Sanat Aidarbayev

2020 ◽  
Vol 17 (35) ◽  
pp. 663-677
Author(s):  
Gulnaz MOLDABAYEVA ◽  
Raikhan SULEIMENOVA ◽  
Akmaral KARIMOVA ◽  
Nurken AKHMETOV ◽  
Lyailya MARDANOVA

One of the chemical methods of stimulating the reservoir to increase the efficiency of the oil field development process is polymer flooding. This article conducted a feasibility study of the effectiveness of the application of polymer flooding technology in one field in Western Kazakhstan. This field is characterized by high viscosity of reservoir oil, water cut, and dynamic heterogeneity of the reservoir. World experience in the application of polymer flooding in analogous fields shows high technological efficiency. Presented results of the analysis of the experience of applying technology in analogous fields, physicochemical studies of polymers, filtration studies on bulk models, hydrodynamic modeling of polymer flooding and the expected cost-effectiveness of introducing the technology, as applied to the conditions of the Karazhanbas oil field with high viscosity of reservoir oil. The analysis based on the experience of applying polymer flooding in high-viscosity oil fields, laboratory studies and estimated calculations of the expected production in the sector geological and hydrodynamic model shows a decrease in water cut, an increase in oil production, and an increase in current and final oil recovery.


Energies ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1637
Author(s):  
Yi Zhang ◽  
Jiexiang Wang ◽  
Peng Jia ◽  
Xiao Liu ◽  
Xuxu Zhang ◽  
...  

Multilayer separate polymer injection in concentric dual-tubing is a special method for enhancing oil recovery in later development stage of the multilayer formation. During the injection process, heat exchange occurs among the inner tubing, tubing annulus and formation, making the thermal transfer process more complicated than traditional one. This work focuses on the polymer flowing characteristics during the multilayer separate polymer flooding injection process in the wellbore. A temperature–viscosity numerical model is derived to investigate the influencing factors on polymer dual-tubing injection process. Then, an estimate-correct method is introduced to derive the numerical solutions. Several influences have been discussed, including the axial temperature distribution, viscosity distribution, pressure drop, and flow pattern of polymer. Results show that under low injecting rates, below 5 m3/d, formation temperature will greatly decrease the polymer viscosity. When the injecting rates above 20 m3/d, the polymer just decreases 1–3 mPa·s at the bottom of well, which is really small. Additionally, the temperature distribution, the coefficient of friction under different injecting rates have been discussed. Generally, this method provides a new way to analyze thermal conductivity during the polymer injection process which is meaningful for polymer flooding in the oilfield application.


Author(s):  
D.Zh. Akhmed-Zaki ◽  
T.S. Imankulov ◽  
B. Matkerim ◽  
B.S. Daribayev ◽  
K.A. Aidarov ◽  
...  

2012 ◽  
Vol 2 (7) ◽  
pp. 137-139
Author(s):  
Devanshu Pandit ◽  
◽  
Dr. S. M. Yadav Dr. S. M. Yadav

2011 ◽  
Vol 14 (9) ◽  
pp. 761-776 ◽  
Author(s):  
Hamid Emami Meybodi ◽  
Riyaz Kharrat ◽  
Benyamin Yadali Jamaloei

2015 ◽  
Vol 5 (1) ◽  
pp. 513-522
Author(s):  
Jean-Claude N'ZI ◽  
Lassina FONDIO ◽  
Mako Francois De Paul N’GBESSO ◽  
Andé Hortense DJIDJI ◽  
Christophe KOUAME

Thirty accessions of tomato including twenty eight introduced accessions from The World Vegetable Center-AVRDC and as controls, two commercial varieties Mongal and Calinago, were assessed for agronomic performances at the Experimentation and Production Station of Angud dou of the National Agronomic Research Centre (CNRA) located in the South of Cote d Ivoire. The trial was arranged in a randomized block with three replications. The following parameters were determined at vegetative development stage: plant height at flowering stage, susceptibility of accessions to diseases, day to 50% flowering and day of first harvest, production duration, fruit length, fruit diameter, total number of fruits, number of fruits per plant, potential yield, net yield and fruit damage rate. Results showed that the commercial variety Mongal, with a potential yield of 15.9 and a net yield of 13.1 t ha-1, was the most productive. All the introduced accessions from AVRDC recorded the lowest potential yields from 2.2 to 9.7 t ha-1, and net yields from 1.7 to 8.6 t ha-1. In addition, accessions WVCT8, FMTT847 and WVCT13 were severely infested by bacterial wilt. The reduction of the net yield of tomato accessions resulted in the high fruit damage rates. For the future tomato breeding work, it would be appropriate to introduce into the trials bacterial diseases tolerant varieties. Moreover, some studies could be undertaken to determine the nature of the bacteria involved in the plant wilting and to find out the causal agent of the tomato plants burning at the fructification stage reducing the harvest duration.


2008 ◽  
Author(s):  
He Liu ◽  
Xiaoqin zhang ◽  
Wenting Guan ◽  
Nan Meng ◽  
Changsen Lu ◽  
...  
Keyword(s):  

Sign in / Sign up

Export Citation Format

Share Document