The Measurement of Crude Oil/Natural Gas/Water Flow Rates by Using Microwave Technique

Author(s):  
Feng Lin ◽  
Xuejun Chen ◽  
Fangde Zhou
2020 ◽  
Vol 16 (9) ◽  
pp. 1656-1673
Author(s):  
V.V. Smirnov

Subject. The article discusses financial and economic momenta. Objectives. I determine financial and economic momenta as the interest rate changes in Russia. Methods. The study is based on a systems approach and the method of statistical analysis. Results. The Russian economy was found to strongly depend on prices for crude oil and natural gas, thus throwing Russia to the outskirts of the global capitalism, though keeping the status of an energy superpower, which ensures a sustainable growth in the global economy by increasing the external consumption and decreasing the domestic one. The devaluation of the national currency, a drop in tax revenue, etc. result from the decreased interest rate. They all require to increase M2 and the devalued retail loan in RUB, thus rising the GDP deflator. As for positive effects, the Central Bank operates sustainably, replenishes gold reserves and keeps the trade balance (positive balance), thus strengthening its resilience during a global drop in crude oil prices and the COVID-19 pandemic. The positive effects were discovered to result from a decreased in the interest rate, rather than keeping it low all the time. Conclusions and Relevance. As the interest rate may be, the financial and economic momentum in Russia depends on the volatility of the price for crude oil and natural gas. Lowering the interest rate and devaluing the national currency, the Central Bank preserves the resource structure of the Russian economy, strengthens its positions within the global capitalism and keeps its status of an energy superpower, thus reinforcing its resilience against a global drop in oil prices.


2018 ◽  
Vol 36 (16) ◽  
pp. 1222-1228 ◽  
Author(s):  
Jasmina Perisic ◽  
Marina Milovanovic ◽  
Ivana Petrovic ◽  
Ljiljana Radovanovic ◽  
Marko Ristic ◽  
...  

2021 ◽  
pp. 014459872098811
Author(s):  
Yuanyuan Zhang ◽  
Zhanli Ren ◽  
Youlu Jiang ◽  
Jingdong Liu

To clarify the characteristics and enrichment rules of Paleogene tight sandstone reservoirs inside the rifted-basin of Eastern China, the third member of Shahejie Formation (abbreviated as Es3) in Wendong area of Dongpu Depression is selected as the research object. It not only clarified the geochemical characteristics of oil and natural gas in the Es3 of Wendong area through testing and analysis of crude oil biomarkers, natural gas components and carbon isotopes, etc.; but also compared and explained the types and geneses of oil and gas reservoirs in slope zone and sub-sag zone by matching relationship between the porosity evolution of tight reservoirs and the charging process of hydrocarbons. Significant differences have been found between the properties and the enrichment rules of hydrocarbon reservoirs in different structural areas in Wendong area. The study shows that the Paleogene hydrocarbon resources are quasi-continuous distribution in Wendong area. The late kerogen pyrolysis gas, light crude oil, medium crude oil, oil-cracked gas and the early kerogen pyrolysis gas are distributed in a semicircle successively, from the center of sub-sag zone to the uplift belt, that is the result of two discontinuous hydrocarbon charging. Among them, the slope zone is dominated by early conventional filling of oil-gas mixture (at the late deposition period of Dongying Formation, about 31–27 Ma ago), while the reservoirs are gradually densified in the late stage without large-scale hydrocarbon charging (since the deposition stage of Minghuazhen Formation, about 6–0 Ma). In contrast, the sub-sag zone is lack of oil reservoirs, but a lot of late kerogen pyrolysis gas reservoirs are enriched, and the reservoir densification and hydrocarbon filling occur in both early and late stages.


Designs ◽  
2021 ◽  
Vol 5 (1) ◽  
pp. 4
Author(s):  
Dillon Alexander Wilson ◽  
Kul Pun ◽  
Poo Balan Ganesan ◽  
Faik Hamad

Microbubble generators are of considerable importance to a range of scientific fields from use in aquaculture and engineering to medical applications. This is due to the fact the amount of sea life in the water is proportional to the amount of oxygen in it. In this paper, experimental measurements and computational Fluid Dynamics (CFD) simulation are performed for three water flow rates and three with three different air flow rates. The experimental data presented in the paper are used to validate the CFD model. Then, the CFD model is used to study the effect of diverging angle and throat length/throat diameter ratio on the size of the microbubble produced by the Venturi-type microbubble generator. The experimental results showed that increasing water flow rate and reducing the air flow rate produces smaller microbubbles. The prediction from the CFD results indicated that throat length/throat diameter ratio and diffuser divergent angle have a small effect on bubble diameter distribution and average bubble diameter for the range of the throat water velocities used in this study.


Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 237
Author(s):  
Michal Brezina ◽  
Tomas Mauder ◽  
Lubomir Klimes ◽  
Josef Stetina

The paper presents the comparison of optimization-regulation algorithms applied to the secondary cooling zone in continuous steel casting where the semi-product withdraws most of its thermal energy. In steel production, requirements towards obtaining defect-free semi-products are increasing day-by-day and the products, which would satisfy requirements of the consumers a few decades ago, are now far below the minimum required quality. To fulfill the quality demands towards minimum occurrence of defects in secondary cooling as possible, some regulation in the casting process is needed. The main concept of this paper is to analyze and compare the most known metaheuristic optimization approaches applied to the continuous steel casting process. Heat transfer and solidification phenomena are solved by using a fast 2.5D slice numerical model. The objective function is set to minimize the surface temperature differences in secondary cooling zones between calculated and targeted surface temperatures by suitable water flow rates through cooling nozzles. Obtained optimization results are discussed and the most suitable algorithm for this type of optimization problem is identified. Temperature deviations and cooling water flow rates in the secondary cooling zone, together with convergence rate and operation times needed to reach the stop criterium for each optimization approach, are analyzed and compared to target casting conditions based on a required temperature distribution of the strand. The paper also contains a brief description of applied heuristic algorithms. Some of the algorithms exhibited faster convergence rate than others, but the optimal solution was reached in every optimization run by only one algorithm.


Sign in / Sign up

Export Citation Format

Share Document