scholarly journals Theoretically Investigation On The Roughness Profile of The Machined Surface After Flank Milling

2021 ◽  
Author(s):  
Jixiong Fei ◽  
Bin Lin ◽  
Shuai Yan
Keyword(s):  
Surface Topography ◽  
End Milling ◽  
Cutting Speed ◽  
Axial Direction ◽  
Flank Milling ◽  
Machined Surface ◽  
Roughness Profile ◽  
Helical Angle ◽  
Radial Depth ◽  
Flank Surface

Abstract In this study, the roughness profile of a machined surface obtained via a flank milling process is thoroughly investigated through theoretical modeling and experimental demonstrations. First, the roughness profile of a machined surface generated by a single-tooth end milling cutter along a straight path is considered (without helical angle). The trajectory of a point on the cutting edge is constructed according to the cutting kinematics, and the roughness profile of the flank surface is theoretically extracted from the trajectory. The surface topography is constructed by integrating the roughness profile along the axial direction of the cutter. Based on the constructed roughness profile model, the effects of cutting parameters on the roughness profile are discussed, including those of the cutting speed, radial depth of the cut, and feed rate. In addition, the effects of cutter geometries including the cutter tooth number, tooth spacing angle, and helical angle on the roughness profile and surface topography are discussed. Further, roughness profiles are constructed for cutter feeds along different tool paths, such as round and curved paths. Finally, experiments are conducted to verify the method developed in this study. The results show that the roughness profile obtained from testing matches well with the theoretically modeled profile. Moreover, the methodology for constructing the roughness profile is compared to an existing approach, which shows that the method in this study is significantly faster.

A Comprehensive Study on Surface Roughness in Machining of AISI D2 Hardened Steel

2012 ◽  
Vol 576 ◽  
pp. 60-63 ◽  
Author(s):  
N.A.H. Jasni ◽  
Mohd Amri Lajis
Keyword(s):  
Surface Roughness ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Hardened Steel ◽  
Depth Of Cut ◽  
Feed Speed ◽  
Radial Depth ◽  
Aisi D2 ◽  
Coated Carbide

Hard milling of hardened steel has wide application in mould and die industries. However, milling induced surface finish has received little attention. An experimental investigation is conducted to comprehensively characterize the surface roughness of AISI D2 hardened steel (58-62 HRC) in end milling operation using TiAlN/AlCrN multilayer coated carbide. Surface roughness (Ra) was examined at different cutting speed (v) and radial depth of cut (dr) while the measurement was taken in feed speed, Vf and cutting speed, Vc directions. The experimental results show that the milled surface is anisotropic in nature. Surface roughness values in feed speed direction do not appear to correspond to any definite pattern in relation to cutting speed, while it increases with radial depth-of-cut within the range 0.13-0.24 µm. In cutting speed direction, surface roughness value decreases in the high speed range, while it increases in the high radial depth of cut. Radial depth of cut is the most influencing parameter in surface roughness followed by cutting speed.

scholarly journals Influence of Chatter of VMC Arising During End Milling Operation and Cutting Conditions on Quality of Machined Surface

1970 ◽  
Vol 2 (1) ◽  
Author(s):  
A.K.M.N. Amin, M.A. Rizal, and M. Razman
Keyword(s):  
Surface Roughness ◽  
Metal Cutting ◽  
Metal Removal ◽  
End Milling ◽  
Cutting Speed ◽  
Cutting Conditions ◽  
End Mill ◽  
Machined Surface ◽  
Operating Cycle ◽  
Wide Range

Machine tool chatter is a dynamic instability of the cutting process. Chatter results in poor part surface finish, damaged cutting tool, and an irritating and unacceptable noise. Exten¬sive research has been undertaken to study the mechanisms of chatter formation. Efforts have been also made to prevent the occurrence of chatter vibration. Even though some progress have been made, fundamental studies on the mechanics of metal cutting are necessary to achieve chatter free operation of CNC machine tools to maintain their smooth operating cycle. The same is also true for Vertical Machining Centres (VMC), which operate at high cutting speeds and are capable of offering high metal removal rates. The present work deals with the effect of work materials, cutting conditions and diameter of end mill cutters on the frequency-amplitude characteristics of chatter and on machined surface roughness. Vibration data were recorded using an experimental rig consisting of KISTLER 3-component dynamometer model 9257B, amplifier, scope meters and a PC.  Three different types of vibrations were observed. The first type was a low frequency vibration, associated with the interrupted nature of end mill operation. The second type of vibration was associated with the instability of the chip formation process and the third type was due to chatter. The frequency of the last type remained practically unchanged over a wide range of cutting speed.  It was further observed that chip-tool contact processes had considerable effect on the roughness of the machined surface.Key Words: Chatter, Cutting Conditions, Stable Cutting, Surface Roughness.

Cutting Forces and Surface Roughness in High-Speed End Milling of Ti6Al4V

2013 ◽  
Vol 589-590 ◽  
pp. 76-81
Author(s):  
Fu Zeng Wang ◽  
Jun Zhao ◽  
An Hai Li ◽  
Jia Bang Zhao
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Cutting Forces ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Wide Range ◽  
Radial Depth ◽  
Coated Carbide

In this paper, high speed milling experiments on Ti6Al4V were conducted with coated carbide inserts under a wide range of cutting conditions. The effects of cutting speed, feed rate and radial depth of cut on the cutting forces, chip morphologies as well as surface roughness were investigated. The results indicated that the cutting speed 200m/min could be considered as a critical value at which both relatively low cutting forces and good surface quality can be obtained at the same time. When the cutting speed exceeds 200m/min, the cutting forces increase rapidly and the surface quality degrades. There exist obvious correlations between cutting forces and surface roughness.

An Approach to Improve Cutting Performance in Micromilling of Titanium Alloy

2020 ◽  
Vol 8 (2) ◽  
Author(s):  
Yunn-Shiuan Liao ◽  
Tsung-Hsien Li ◽  
Yi-Chen Liu
Keyword(s):  
Carbon Dioxide ◽  
Surface Roughness ◽  
Titanium Alloy ◽  
Flank Wear ◽  
End Milling ◽  
Cutting Speed ◽  
Liquid Carbon ◽  
Dry Cutting ◽  
Machined Surface ◽  
Liquid Carbon Dioxide

Abstract Application of liquid carbon dioxide to improve cutting performance in micro-end milling of Ti-6Al-4V titanium alloy was proposed in this study. It was found that the machined roughness decreased with the cutting speed as observed in the conventional cutting, when a 0.5 mm diameter end milling cutter was used in dry cutting. But, the tiny and shattered chips produced by the use of 0.3 mm diameter cutter could adhere on the machined surface and deteriorate surface finish, if the cutting speed was higher than 40 m/min. Cutting temperature was effectively decreased by applying liquid carbon dioxide during micromilling, which in turn reduced the amount of chips adhering on the machined surface and lowered flank wear. The surface roughness Ra at a cutting speed of 70 m/min was improved from 0.09 μm under dry cutting to 0.04 μm under the liquid carbon dioxide assisted cutting condition. And there were no flank wear and very few burrs left on the machined surface for the condition used in the experiment. The height of the burrs was only 25% of that under dry cutting. More, minimum quantity lubrication (MQL) was proposed to be applied together with the liquid carbon dioxide to enhance lubrication effect. It was noted that the machined surface roughness was further decreased by 15% as compared with that when the liquid carbon dioxide was applied alone. The height of burrs was reduced from 32 μm to 16 μm.

scholarly journals Effects of Feed per Tooth and Radial Depth of Cut on Amplitude Parameters and Power Spectral Density of a Machined Surface

Materials ◽  
2020 ◽  
Vol 13 (6) ◽  
pp. 1323
Author(s):  
Qing Zhang ◽  
Song Zhang
Keyword(s):  
Spectral Density ◽  
Surface Topography ◽  
Power Spectral Density ◽  
End Milling ◽  
Spectral Energy ◽  
Depth Of Cut ◽  
Power Spectral ◽  
Radial Depth ◽  
Milled Surface ◽  
Step Over

Surface topography and roughness significantly affect the functional properties of engineering parts. In this study, a mathematical model simulating the surface topography in end milling is presented and verified by milling experiments. The three dimensional (3D) surface amplitude parameters (arithmetic average deviation Sba and root mean square deviation Sq) of the milled surface were calculated by using the model and the effects of the product (p) and ratio (r) of radial depth of cut ae and feed per tooth fz on amplitude parameters were researched. To evaluate the lateral characteristics of the milled surface, one dimensional (1D) power spectral densities (PSD) along both feed and step-over direction were calculated and investigated. It was found that fz affects 1D PSD along both directions, whereas ae affects 1D PSD along the step-over direction. An angular spectrum, derived from the area power spectral density (APSD), was employed to research the spatial distribution of spectral energy on the milled surface. Furthermore, the influences of p and r on the PSD properties were researched. It was found that r is the significant factor that influences the direction of surface energy spectrum distribution.

A New Algorithm for the Numerical Simulation of Machined Surface Topography in Multiaxis Ball-End Milling

2008 ◽  
Vol 130 (1) ◽  
Author(s):  
Wei-Hong Zhang ◽  
Gang Tan ◽  
Min Wan ◽  
Tong Gao ◽  
David Hicham Bassir
Keyword(s):  
Numerical Simulation ◽  
Surface Topography ◽  
End Milling ◽  
Computing Time ◽  
Cutting Edge ◽  
Machining Parameters ◽  
Step Method ◽  
Time Step ◽  
Machined Surface ◽  
Ball End Milling

In milling process, surface topography is a significant factor that affects directly the surface integrity and constitutes a supplement to the form error associated with the workpiece deformation. Based on the tool machining paths and the trajectory equation of the cutting edge relative to the workpiece, a new and general iterative algorithm is developed here for the numerical simulation of the machined surface topography in multiaxis ball-end milling. The influences of machining parameters such as the milling modes, cutter runout, cutter inclination direction, and inclination angle upon the topography and surface roughness values are studied in detail. Compared with existing methods, the basic advantages and novelties of the proposed method can be resumed below. First, it is unnecessary to discretize the cutting edge and tool feed motion and rotation motion. Second, influences of cutting modes and cutter inclinations are studied systematically and explicitly for the first time. The generality of the algorithm makes it possible to calculate the pointwise topography value on any sculptured surface of the workpiece. Besides, the proposed method is proved to be more efficient in saving computing time than the time step method that is commonly used. Finally, some examples are presented and simulation results are compared with experimental ones.

Experimental Study of End Milling Force on Manganese Steel

2013 ◽  
Vol 718-720 ◽  
pp. 239-243
Author(s):  
Girma Seife Abebe ◽  
Ping Liu
Keyword(s):  
Cutting Force ◽  
Feed Rate ◽  
End Milling ◽  
Cutting Speed ◽  
Second Order ◽  
Manganese Steel ◽  
Depth Of Cut ◽  
Machining Deformation ◽  
Radial Depth ◽  
Axial Depth

Cutting force is a key factor influencing the machining deformation of weak rigidity work pieces. In order to reduce the machining deformation and improve the process precision and the surface quality, it is necessary to study the factors influencing the cutting force and build the regression model of cutting forces. This paper discusses the development of the first and second order models for predicting the cutting force produced in end-milling operation of modified manganese steel. The first and second order cutting force equations are developed using the response surface methodology (RSM) to study the effect of four input cutting parameters (cutting speed, feed rate, radial depth and axial depth of cut) on cutting force. The separate effect of individual input factors and the interaction between these factors are also investigated in this study. The received second order equation shows, based on the variance analysis, that the most influential input parameter was the feed rate followed by axial depth, and radial depth of cut. It was found that the interaction of feed with axial depth was extremely strong. In addition, the interactions of feed with radial depth; and feed rate with radial depth of cut were observed to be quite significant. The predictive models in this study are believed to produce values of the longitudinal component of the cutting force close to those readings recorded experimentally with a 95% confident interval.

Experimental Research of Effective Cutting Speed Influence on Surface Roughness in Ball End Milling of C45 Material with Hardness 34 HRC

2014 ◽  
Vol 657 ◽  
pp. 53-57 ◽  
Author(s):  
Sándor Ravai Nagy ◽  
Ioan Paşca ◽  
Mircea Lobonțiu ◽  
Mihai Banica
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Experimental Research ◽  
Inclination Angle ◽  
Cutting Tool ◽  
End Milling ◽  
Cutting Speed ◽  
Cnc Machine Tools ◽  
Machined Surface ◽  
Ball End Milling

Machining of Complex Concave or Convex Surfaces Requires the Use of Ball End Milling Cutters. Obtaining the Expected Surface Quality Compete Various Technological Factors which should be Taken into Account. Following the Machining of the Surface with Different Inclination Angles between the Cutting Tool Axes and the Machined Surface, Significant Changes of the Surface Roughness have been Observed. Based on the Tests Performed, we can Determine the Range of the Tool Inclination Angle, which is the Best for the Surface Quality. we have also Made a Correlation between the Cutting Speeds, Inclination Angle of the Cutting Tool Toward the Machined Surface for an Obtained Surface Quality. the Presented Results are Based on Experimental Research in Industrial Conditions by Using CNC Machine Tools with 5 Axes. the Tests have been Performed on the C45 Material, Heat Treated to 34HRC.

Sign in / Sign up

Export Citation Format

Share Document