scholarly journals Supplemental Far-red Light-emitting Diode Light Increases Growth of Foxglove Seedlings Under Sole-source Lighting

2020 ◽  
Vol 30 (5) ◽  
pp. 564-569
Author(s):  
Claudia Elkins ◽  
Marc W. van Iersel
Keyword(s):  
Flux Density ◽  
Plant Height ◽  
Light Emitting Diode ◽  
Red Light ◽  
Dry Weight ◽  
Sole Source ◽  
Photon Flux ◽  
Photon Flux Density ◽  
Light Emitting ◽  
Light Intensities

Seedlings may be grown indoors where environmental conditions can be precisely controlled to ensure consistent and reliable production. The optimal spectrum for production under sole-source lighting is currently unknown. Far-red light (λ = 700–800 nm) typically is not a significant part of the spectrum of light-emitting diode (LED) grow lights. However, far-red light is photosynthetically active and can enhance leaf elongation, which may result in larger leaves and increased light interception. We hypothesized that adding far-red light to sole-source lighting would increase the growth of ‘Dalmatian Peach’ foxglove (Digitalis purpurea) seedlings grown under white LED lights, potentially shortening production times. Our objective was to evaluate the effect of far-red light intensities, ranging from 4.0 to 68.8 µmol·m−2·s−1, on the growth and morphology of foxglove seedlings. Foxglove seedlings were grown in a growth chamber with a photosynthetic photon flux density (PPFD) of 186 ± 6.4 μmol·m−2·s−1 and supplemental far-red light intensities ranging from 4.0 to 68.8 µmol·m−2·s−1. As far-red light increased, shoot dry weight, root dry weight, plant height, and plant height/number of leaves increased by 38% (P = 0.004), 20% (P = 0.029), 38% (P = 0.025), and 34% (P = 0.024), respectively, while root weight fraction decreased 16% (P = 0.034). Although we expected supplemental far-red light to induce leaf and/or stem expansion, specific leaf area and compactness (two measures of morphology) were unaffected. Because a 37% increase in total photon flux density (PPFD plus far-red light) resulted in a 34.5% increase in total plant dry weight, the increased growth likely was due to increased photosynthesis rather than a shade-acclimation response. The growth response was linear across the 4.0 to 68.8 µmol·m−2·s−1 range of far-fed light tested, so we were unable to determine a saturating far-red photon flux density.

scholarly journals Blue Light Monochromatic Irradiation for 12 Hours in Lighting Pattern with Combinations of Blue and Red Light Elongates Young Cos Lettuce Leaves and Promotes Growth under High Daily Light Integral

HortScience ◽  
2021 ◽  
pp. 1-6
Author(s):  
Tomohiro Jishi ◽  
Ryo Matsuda ◽  
Kazuhiro Fujiwara
Keyword(s):  
Flux Density ◽  
Blue Light ◽  
Light Emitting Diode ◽  
Red Light ◽  
Dry Weight ◽  
Photosynthetic Photon Flux Density ◽  
Photon Flux ◽  
Photon Flux Density ◽  
Photosynthetic Photon Flux ◽  
Leaf Elongation

Cos lettuce was grown under different spectral photon flux density distribution (SPFD) change patterns with blue- and/or red light-emitting diode (LED) irradiation with a 24-hour cycle. Twelve treatments were designed with a combination of four relative SPFD (RSPFD) change patterns and three photosynthetic photon flux density (PPFD) levels. The RSPFD change patterns were as follows: BR/BR, simultaneous blue- and red-light irradiation (BR) for 24 h; R/BR, red-light monochromatic irradiation (R) for 12 h followed by 12 hours of BR; B/BR, blue-light monochromatic irradiation (B) for 12 hours followed by 12 hours of BR; and B/R, 12 hours of B followed by 12 hours of R. Each RSPFD change pattern was conducted at three daily average photosynthetic photon flux densities (PPFDave) of 50, 100, and 200 µmol·m−2·s−1. The RSPFD change patterns that included B (B/BR and B/R) resulted in elongated leaves. A low ratio of active phytochrome to total phytochrome under B was considered the reason for leaf elongation. Shoot dry weight was significantly greater under the RSPFD change patterns that included B when the PPFDave was 200 µmol·m−2·s−1. The leaf elongation caused by B would have increased the amount of light received and thereby promoted growth. However, excessive leaf elongation caused the plants to fall, and growth was not promoted under the RSPFD change patterns that included B when the PPFDave was 50 µmol·m−2·s−1. Thus, 12-hour B promoted growth under conditions in which leaf elongation leads to increases in the amount of light received.

scholarly journals Growth and Appearance Quality of Four Microgreen Species under Light-emitting Diode Lights with Different Spectral Combinations

HortScience ◽  
2020 ◽  
Vol 55 (9) ◽  
pp. 1399-1405
Author(s):  
Qinglu Ying ◽  
Yun Kong ◽  
Youbin Zheng
Keyword(s):  
Plant Height ◽  
High Intensity ◽  
Light Emitting Diode ◽  
Red Light ◽  
Photon Flux ◽  
Photon Flux Density ◽  
Light Emitting ◽  
Led Light ◽  
Red Led ◽  
Dry Biomass

To investigate plant growth and quality responses to different light spectral combinations, cabbage (Brassica oleracea L. var. capitata f. rubra), kale (Brassica napus L. ‘Red Russian’), arugula (Eruca sativa L.), and mustard (Brassica juncea L. ‘Ruby steak’) microgreens were grown in a controlled environment using sole-source light with six different spectra: 1) FL: cool white fluorescent light; 2) BR: 15% blue and 85% red light-emitting diode (LED); 3) BRFRL: 15% blue, 85% red, and 15.5 µmol·m−2·s−1 far-red (FR) LED; 4) BRFRH: 15% blue, 85% red, and 155 µmol·m−2·s−1 FR LED; 5) BGLR: 9% blue, 6% green, and 85% red LED; and 6) BGHR: 5% blue, 10% green, and 85% red LED. For all the light treatments, the total photosynthetic photon flux density (PPFD) was set at ≈330 µmol·m−2·s−1 under a 17-hour photoperiod, and the air temperature was ≈21 °C with 73% relative humidity (RH). At harvest, BR vs. FL increased plant height for all the tested species except arugula, and enlarged cotyledon area for kale and arugula. Adding high-intensity FR light to blue and red light (i.e., BRFRH) further increased plant height for all species, and cotyledon area for mustard, but it did not affect the fresh or dry biomass for any species. Also, BRFRH vs. BR increased cotyledon greenness for green-leafed species (i.e., arugula, cabbage, and kale), and reduced cotyledon redness for red-leafed mustard. However, BGLR, BGHR, and BRFRL, compared with BR, did not affect plant height, cotyledon area, or fresh or dry biomass. These results suggest that the combination of 15% blue and 85% red LED light can potentially replace FL as the sole light source for indoor production of the tested microgreen species. Combining high-intensity FR light, rather than low-level (≤10%) green light, with blue and red light could be taken into consideration for the optimization of LED light spectral quality in microgreen production under environmental conditions similar to this experiment.

The value of red light at night for increasing basil yield

2018 ◽  
Vol 98 (6) ◽  
pp. 1321-1330
Author(s):  
Jaimin S. Patel ◽  
Leora Radetsky ◽  
Mark S. Rea
Keyword(s):  
Plant Height ◽  
Red Light ◽  
Leaf Size ◽  
Cost Effective ◽  
Dry Weight ◽  
Photosynthetic Photon Flux Density ◽  
Photon Flux ◽  
Photon Flux Density ◽  
Light At Night ◽  
Sweet Basil

Sweet basil (Ocimum basilicum L.) is primarily used for culinary purposes, but it is also used in the fragrance and medicinal industries. In the last few years, global sweet basil production has been significantly impacted by downy mildew caused by Peronospora belbahrii Thines. Nighttime exposure to red light has been shown to inhibit sporulation of P. belbahrii. The objective of this study was to determine if nighttime exposure to red light from light-emitting diodes (λmax = 625 nm) could increase plant growth (plant height and leaf size) and yield (number and weight of leaves) in basil plants. In two sets of greenhouse experiments, red light was applied at a photosynthetic photon flux density of 60 μmol m−2 s−1 during the otherwise dark night for 10 h (from 2000 to 0600). The results demonstrate that exposure to red light at night can increase the number of basil leaves per plant, plant height, leaf size (length and width), and leaf fresh and dry weight compared with plants in darkness at night. The addition of incremental red light at night has the potential to be cost-effective for fresh organic basil production in controlled environments.

scholarly journals LightCue: An Innovative Far-Red Light Emitter for Locally Modifying the Spectral Cue in Outdoor Conditions with Global Consequences on Plant Architecture

Plants ◽  
2021 ◽  
Vol 10 (11) ◽  
pp. 2483
Author(s):  
Alain Fortineau ◽  
Didier Combes ◽  
Céline Richard-Molard ◽  
Ela Frak ◽  
Alexandra Jullien
Keyword(s):  
Plant Architecture ◽  
Light Emitting Diode ◽  
Red Light ◽  
Inhibitory Effect ◽  
Photosynthetic Photon Flux Density ◽  
High Irradiance ◽  
Light Signal ◽  
Photon Flux ◽  
Photon Flux Density ◽  
Light Emitting

Plasticity of plant architecture is a promising lever to increase crop resilience to biotic and abiotic damage. Among the main drivers of its regulation are the spectral signals which occur via photomorphogenesis processes. In particular, branching, one of the yield components, is responsive to photosynthetic photon flux density (PPFD) and to red to far-red ratio (R:FR), both signals whose effects are tricky to decorrelate in the field. Here, we developed a device consisting of far-red light emitting diode (LED) rings. It can reduce the R:FR ratio to 0.14 in the vicinity of an organ without changing the PPFD in outdoor high irradiance fluctuating conditions, which is a breakthrough as LEDs have been mostly used in non-fluctuant controlled conditions at low irradiance over short periods of time. Applied at the base of rapeseed stems during the whole bolting-reproductive phase, LightCue induced an expected significant inhibitory effect on two basal targeted axillary buds and a strong unexpected stimulatory effect on the overall plant aerial architecture. It increased shoot/root ratio while not modifying the carbon balance. LightCue therefore represents a promising device for progress in the understanding of light signal regulation in the field.

scholarly journals Application of an Automatic Control System of Photosynthetic Photon Flux Density for LED-Low Light Irradiation Storage of Green Plants

2005 ◽  
Vol 15 (4) ◽  
pp. 781-786 ◽  
Author(s):  
Kazuhiro Fujiwara ◽  
Toshinari Sawada ◽  
Yoshikatsu Kimura ◽  
Kenji Kurata
Keyword(s):  
Flux Density ◽  
Blue Light ◽  
Red Light ◽  
Dry Weight ◽  
Photosynthetic Photon Flux Density ◽  
Light Irradiation ◽  
Photon Flux ◽  
Photon Flux Density ◽  
Photosynthetic Photon Flux ◽  
Low Light

A light-emitting diode (LED)-low light irradiation (LLI) storage system was developed for suppressing the change in dry weight and maintaining the quality of green plants during long-term storage. In this system, the carbon dioxide (CO2) exchange rate was maintained at zero by automatically adjusting the photosynthetic photon flux density (PPFD) with a proportional-integralderivative (PID) controller. The voltage supplied to the LEDs was controlled by the difference between the inflow (400 μmol·mol-1) and outflow CO2 concentrations in the storage case. Grafted tomato (Lycopersicon esculentum; scion = `House Momotaro'; rootstock = `Anchor T') plug seedlings were stored at 10 °C for 35 days under four different LLI conditions as a system operating test: fixed red light irradiation at 2 μmol·m-2·s-1, PID-controlled red light irradiation with no blue light, and PID-controlled red light irradiation with blue light at 0.2 or 1.0 μmol·m-2·s-1. The results showed that the automatic PPFD control during LED-LLI helped suppress changes in dry weight during storage as expected. Furthermore, it was found that addition of a low percentage of blue light improved the morphological appearance of the seedlings and reduced the PPFD required to suppress the change in dry weight.

scholarly journals Blue Radiation Interacts with Green Radiation to Influence Growth and Predominantly Controls Quality Attributes of Lettuce

2020 ◽  
Vol 145 (2) ◽  
pp. 75-87 ◽  
Author(s):  
Qingwu Meng ◽  
Jennifer Boldt ◽  
Erik S. Runkle
Keyword(s):  
Avoidance Response ◽  
Flux Density ◽  
Light Emitting Diode ◽  
Sole Source ◽  
Dry Mass ◽  
Photosynthetic Photon Flux Density ◽  
Photon Flux ◽  
Photon Flux Density ◽  
Shade Avoidance ◽  
White Leds

Adding green [G (500–600 nm)] radiation to blue [B (400–500 nm)] and red [R (600–700 nm)] radiation creates white radiation and improves crop inspection at indoor farms. Although G radiation can drive photosynthesis and elicit the shade-avoidance response, its effects on plant growth and morphology have been inconsistent. We postulated G radiation would counter the suppression of crop growth and promotion of secondary metabolism by B radiation depending on the B photon flux density (PFD). Lettuce (Lactuca sativa ‘Rouxai’) was grown in a growth room under nine sole-source light-emitting diode (LED) treatments with a 20-hour photoperiod or in a greenhouse. At the same photosynthetic photon flux density [PPFD (400–700 nm)] of 180 μmol·m−2·s−1, plants were grown under warm-white LEDs or increasing B PFDs at 0, 20, 60, and 100 μmol·m−2·s−1 with or without substituting the remaining R radiation with 60 μmol·m−2·s−1 of G radiation. Biomass and leaf expansion were negatively correlated with the B PFD with or without G radiation. For example, increasing the B PFD decreased fresh and dry mass by up to 63% and 54%, respectively. The inclusion of G radiation did not affect shoot dry mass at 0 or 20 μmol·m−2·s−1 of B radiation, but it decreased it at 60 or 100 μmol·m−2·s−1 of B radiation. Results suggest that the shade-avoidance response is strongly elicited by low B radiation and repressed by high B radiation, rendering G radiation ineffective at controlling morphology. Moreover, substituting R radiation with G radiation likely reduced the quantum yield. Otherwise, G radiation barely influenced morphology, foliage coloration, essential nutrients, or sensory attributes regardless of the B PFD. Increasing the B PFD increased red foliage coloration and the concentrations of several macronutrients (e.g., nitrogen and magnesium) and micronutrients (e.g., zinc and copper). Consumers preferred plants grown under sole-source lighting over those grown in the greenhouse, which were more bitter and less acceptable, flavorful, and sweet. We concluded that lettuce phenotypes are primarily controlled by B radiation and that G radiation maintains or suppresses lettuce growth depending on the B PFD.

scholarly journals Regulating Flowering and Extension Growth of Poinsettia Using Red and Far-red Light-emitting Diodes for End-of-day Lighting

HortScience ◽  
2019 ◽  
Vol 54 (2) ◽  
pp. 323-327 ◽  
Author(s):  
Mengzi Zhang ◽  
Erik S. Runkle
Keyword(s):  
Light Emitting Diode ◽  
Red Light ◽  
Extension Growth ◽  
Moderate Intensity ◽  
Photon Flux ◽  
Photon Flux Density ◽  
Light Emitting ◽  
Potential Alternative ◽  
Ornamental Crops ◽  
The Impact

Manipulating light quality is a potential alternative method of regulating plant height in the commercial production of ornamental crops. In particular, end-of-day (EOD) lighting with a high red (R; 600–700 nm) to far-red (FR; 700–800 nm) ratio (R:FR) can suppress extension growth, whereas a low R:FR can promote it. We investigated the effects of the R:FR and duration of EOD lighting in regulating extension growth and flowering of two poinsettia cultivars, White Glitter and Marble Star. Plants were grown at 20 °C under 9-hour days with or without EOD lighting provided by two types of light-emitting diode bulbs: R+white+FR (subsequently referred to as R+FR) and FR only. The R:FR ratios were 0.73 and 0.04, respectively, and the photon flux density between 400 and 800 nm was adjusted to 2 to 3 μmol·m−2·s–1 at plant canopy. The six EOD lighting treatments were R+FR or FR for 2 or 4 hours, 2 hours of R+FR followed by 2 hours of FR, and 4 hours of R+FR followed by 2 hours of FR. We also investigated the impact of a 4-hour moderate-intensity (13 μmol·m−2·s–1) EOD FR treatment in the second replication. EOD lighting generally increased poinsettia extension growth, with the greatest promotion under the longest lighting periods. There were no differences in days to first bract color and days to anthesis when the 9-hour day was extended by 2 hours, but flowering was delayed under 4- or 6-hour EOD treatments, except for the 2-hour R+FR + 2-hour FR and 4-hour FR treatments. Four hours of moderate-intensity EOD FR greatly promoted extension growth and delayed or prevented bract coloration in both cultivars. We conclude that EOD lighting promotes extension growth of poinsettia, and specifically, EOD FR at a low intensity (2–3 μmol·m−2·s–1) is not perceived as long-day signal, whereas a higher intensity (13 μmol·m−2·s–1) of FR delays flowering.

scholarly journals Different LED Light Wavelengths and Photosynthetic Photon Flux Density Effect on Colletotrichum acutatum Growth

Plants ◽  
2022 ◽  
Vol 11 (1) ◽  
pp. 143
Author(s):  
Neringa Rasiukevičiūtė ◽  
Aušra Brazaitytė ◽  
Viktorija Vaštakaitė-Kairienė ◽  
Alma Valiuškaitė
Keyword(s):  
Flux Density ◽  
Photosynthetic Photon Flux Density ◽  
Growth Characteristics ◽  
Colletotrichum Acutatum ◽  
Photon Flux ◽  
Photon Flux Density ◽  
Photosynthetic Photon Flux ◽  
Light Emitting ◽  
Led Light ◽  
Fungus Growth

The study aimed to evaluate the effect of different photon flux density (PFD) and light-emitting diodes (LED) wavelengths on strawberry Colletotrichum acutatum growth characteristics. The C. acutatum growth characteristics under the blue 450 nm (B), green 530 nm (G), red 660 nm (R), far-red 735 nm (FR), and white 5700 K (W) LEDs at PFD 50, 100 and 200 μmol m−2 s−1 were evaluated. The effect on C. acutatum mycelial growth evaluated by daily measuring until five days after inoculation (DAI). The presence of conidia and size (width and length) evaluated after 5 DAI. The results showed that the highest inhibition of fungus growth was achieved after 1 DAI under B and G at 50 μmol m−2 s−1 PFD. Additionally, after 1–4 DAI under B at 200 μmol m−2 s−1 PFD. The lowest conidia width was under FR at 50 μmol m−2 s−1 PFD and length under FR at 100 μmol m−2 s−1 PFD. Various LED light wavelengths influenced differences in C. acutatum colonies color. In conclusion, different photosynthetic photon flux densities and wavelengths influence C. acutatum growth characteristics. The changes in C. acutatum morphological and phenotypical characteristics could be related to its ability to spread and infect plant tissues. This study’s findings could potentially help to manage C. acutatum by LEDs in controlled environment conditions.

scholarly journals Critical Photoperiod and Optimal Quality of Night Interruption Light for Runner Induction in June-Bearing Strawberries

Agronomy ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1996
Author(s):  
Yali Li ◽  
Jie Xiao ◽  
Jiangtao Hu ◽  
Byoung Ryong Jeong
Keyword(s):  
Red Light ◽  
Photon Flux ◽  
Photon Flux Density ◽  
Light Emitting ◽  
Red Led ◽  
Critical Photoperiod ◽  
Closed Walk ◽  
White Light Emitting Diodes ◽  
Optimal Quality

The optimal photoperiod and light quality for runner induction in strawberries ‘Sulhyang’ and ‘Maehyang’ were investigated. Two experiments were carried out in a semi-closed walk-in growth chamber with 25/15 °C day/night temperatures and a light intensity of 250 μmol·m–2·s–1photosynthetic photon flux density (PPFD) provided from white light-emitting diodes (LEDs). In the first experiment, plants were treated with a photoperiod of either 12, 14, 16, 18, 20, or 22 h In the second experiment, a total of 4 h of night interruption (NI) light at an intensity of 70 μmol·m–2·s–1PPFD provided from either red, blue, green, white, or far-red LED in addition to 11 h short day (SD). The results showed that both ‘Sulhyang’ and ‘Maehyang’ produced runners when a photoperiod was longer than 16 h, and the number of runners induced positively correlated with the length of photoperiod. However, the plant growth, contents of chlorophyll, sugar and starch, and Fv/Fo decreased in a 22 h photoperiod. All qualities of the NI light, especially red light, significantly increased the number of runners and daughter plants induced per plant as compared with those in the SD treatment in both cultivars. In a conclusion, a photoperiod between 16 and 20 h and NI light, especially red NI light, can be used for quality runner induction in both ‘Sulhyang’ and ‘Maehyang’.

scholarly journals Morphological Response of Soybean (Glycine max (L.) Merr.) Cultivars to Light Intensity and Red to Far-Red Ratio

Agronomy ◽  
2019 ◽  
Vol 9 (8) ◽  
pp. 428 ◽  
Author(s):  
Tina Hitz ◽  
Jens Hartung ◽  
Simone Graeff-Hönninger ◽  
Sebastian Munz
Keyword(s):  
Cropping Systems ◽  
Light Emitting Diode ◽  
Red Light ◽  
Photosynthetic Photon Flux Density ◽  
Photon Flux ◽  
Photon Flux Density ◽  
Shade Avoidance ◽  
Internode Elongation ◽  
Morphological Response ◽  
Petiole Elongation

In soybean production, the shade avoidance response can affect yield negatively in both mono- and inter-cropping systems due to increased heterogeneity of the crop and lodging. This is mainly regulated by photoreceptors responding to the ratio between red and far-red light (R:FR) and photosynthetic photon flux density (PPFD). In this study, three soybean cultivars were grown under different R:FR and PPFD in a light emitting diode (LED) climate chamber to disentangle the effect of each on morphology and dry matter. Results showed that plant organs were influenced differently and indicated an interaction with the increase in assimilates at high PPFD. Internode elongation was mainly influenced by low PPFD with an additive effect from low R:FR, whereas petiole elongation responded strongly under low R:FR. Hence, petiole elongation can be seen as the main response to the threat of shade (high PPFD and low R:FR) and both petiole and internode elongation as a response to true shade (low PPFD and low R:FR). Interactions between cultivar and light treatment were found for internode length and diameter and leaf mass ratio, which may be unique properties for specific cropping systems.

Sign in / Sign up

Export Citation Format

Share Document