An Elementary Formula for Initial Relaxation Modulus from the Creep Compliance of Various Viscoelastic Model

2022 ◽  
Author(s):  
Songqiang Chen ◽  
Wang Jinchang ◽  
Junyan Yi ◽  
Decheng Feng
Keyword(s):  
Creep Compliance ◽  
Viscoelastic Model ◽  
Relaxation Modulus ◽  
Elementary Formula

STRESS RELAXATION OF MAGNETORHEOLOGICAL FLUIDS

2002 ◽  
Vol 16 (17n18) ◽  
pp. 2655-2661
Author(s):  
W. H. LI ◽  
G. CHEN ◽  
S. H. YEO ◽  
H. DU
Keyword(s):  
Stress Relaxation ◽  
Viscoelastic Model ◽  
Relaxation Modulus ◽  
Damping Function ◽  
Mr Fluids ◽  
Large Step ◽  
Linear Viscoelastic ◽  
Predicted Values ◽  
Two Parameters ◽  
Step Strain

In this paper, the experimental and modeling study and analysis of the stress relaxation characteristics of magnetorheological (MR) fluids under step shear are presented. The experiments are carried out using a rheometer with parallel-plate geometry. The applied strain varies from 0.01% to 100%, covering both the pre-yield and post-yield regimes. The effects of step strain, field strength, and temperature on the stress modulus are addressed. For small step strain ranges, the stress relaxation modulus G(t,γ) is independent of step strain, where MR fluids behave as linear viscoelastic solids. For large step strain ranges, the stress relaxation modulus decreases gradually with increasing step strain. Morever, the stress relaxation modulus G(t,γ) was found to obey time-strain factorability. That is, G(t,γ) can be represented as the product of a linear stress relaxation G(t) and a strain-dependent damping function h(γ). The linear stress relaxation modulus is represented as a three-parameter solid viscoelastic model, and the damping function h(γ) has a sigmoidal form with two parameters. The comparison between the experimental results and the model-predicted values indicates that this model can accurately describe the relaxation behavior of MR fluids under step strains.

Effect of Cure State on Stress Relaxation in 3501-6 Epoxy Resin

1997 ◽  
Vol 119 (3) ◽  
pp. 262-265 ◽  
Author(s):  
S. R. White ◽  
A. B. Hartman
Keyword(s):  
Stress Relaxation ◽  
Epoxy Resin ◽  
Creep Compliance ◽  
Numerical Technique ◽  
Matrix Material ◽  
Relaxation Modulus ◽  
Master Curves ◽  
Creep Tests ◽  
Three Point Bending ◽  
Direct Inversion

Little experimental work has been done to characterize how the viscoelastic properties of composite material matrix resins develop during cure. In this paper, the results of a series of creep tests carried out on 3501–6 epoxy resin, a common epoxy matrix material for graphite/epoxy composites, at several different cure states is reported. Beam specimens were isothermally cured at increasing cure temperatures to obtain a range of degrees of cure from 0.66 to 0.99. These specimens were then tested in three-point bending to obtain creep compliance over a wide temperature range. The master curves and shift functions for each degree of cure case were obtained by time-temperature superposition. A numerical technique and direct inversion were used to calculate the stress relaxation modulus master curves from the creep compliance master curves. Direct inversion was shown to be adequate for fully cured specimens, however it underpredicts the relaxation modulus and the transition for partially cured specimens. Correlations with experimental stress relaxation data from Kim and White (1996) showed that reasonably accurate results can be obtained by creep testing followed by numerical conversion using the Hopkins-Hamming method.

EXPERIMENTAL RESEARCH ON VISCOELASTICITY PROPERTY OF DIFFERENT LAYERS PERIODONTAL LIGAMENT UNDER COMPRESSION

2021 ◽  
pp. 2150050
Author(s):  
JINLAI ZHOU ◽  
YANG SONG ◽  
CHENGUANG XU ◽  
CHUNQIU ZHANG ◽  
XUE SHI
Keyword(s):  
Elastic Modulus ◽  
Periodontal Ligament ◽  
Creep Compliance ◽  
Relaxation Modulus ◽  
Maxwell Model ◽  
Kelvin Model ◽  
Generalized Maxwell Model ◽  
Relaxation Stress ◽  
Generalized Kelvin Model ◽  
Fitting Accuracy

The periodontal ligament (PDL) exhibits different material mechanical properties along the long axis of the teeth. To explore the creep and the relaxation effects of dissimilar layers of PDL, this paper took the central incisors of porcine mandibular as experimental subjects and divided them perpendicular to the teeth axis into five layers. Creep experiments and relaxation experiments on five layers were conducted to obtain the creep compliance and relaxation modulus at different layers. Linear elastic model, generalized Kelvin model, and generalized Maxwell model were used to describe the major characteristics of the PDL: Instantaneous elasticity, creep and relaxation. Fitting accuracy of three-parameter, five-parameter, and seven-parameter of the model was compared, and the constitutive equations of different layers were established by the least square method. The results presented that the creep strain and the relaxation stress of PDL were exponentially correlated with time under different loading conditions. Different layers showed a significant effect on the creep strain and relaxation stress of PDL. Along the long axis of the teeth, the changing rule of the creep compliance and relaxation modulus of each layer showed quite the contrary, and the instantaneous elastic modulus first decreased to the minimum, then increased to the maximum. Higher instantaneous elastic modulus led to lower creep compliance and higher relaxation modulus. The generalized Kelvin model and the generalized Maxwell model well characterized the creep and relaxation properties of PDL. Fitting accuracy increased with the number of model parameters. The relaxation time of PDL was about one order of magnitude shorter than the creep retardation time, which indicated that the relaxation effect lasted shorter than the creep effect.

Obtaining shear relaxation modulus and creep compliance of linear viscoelastic materials from instrumented indentation using axisymmetric indenters of power-law profiles

2009 ◽  
Vol 24 (10) ◽  
pp. 3013-3017 ◽  
Author(s):  
Yang-Tse Cheng ◽  
Fuqian Yang
Keyword(s):  
Inverse Problem ◽  
Laplace Transform ◽  
Power Law ◽  
Creep Compliance ◽  
Relaxation Modulus ◽  
Instrumented Indentation ◽  
Loading Paths ◽  
Linear Viscoelastic ◽  
Shear Relaxation ◽  
Analytical Expressions

Using Laplace transform, we solve the inverse problem of obtaining the shear relaxation modulus and creep compliance of linear viscoelastic solids from indentation by axisymmetric indenters of power-law profiles. We identify several simple, though nontrivial, loading paths for carrying out indentation measurements such that the inverse problem has analytical solutions. We show that the shear relaxation modulus and creep compliance may be readily obtained using the newly derived analytical expressions together with proposed indentation loading paths.

scholarly journals Study on Relaxation Damage Properties of High Viscosity Asphalt Sand under Uniaxial Compression

2018 ◽  
Vol 2018 ◽  
pp. 1-12 ◽  
Author(s):  
Yazhen Sun ◽  
Zhangyi Gu ◽  
Jinchang Wang ◽  
Chenze Fang ◽  
Xuezhong Yuan
Keyword(s):  
Uniaxial Compression ◽  
Viscoelastic Model ◽  
Relaxation Modulus ◽  
Maxwell Model ◽  
High Viscosity ◽  
Secondary Development ◽  
Compression Tests ◽  
Crack Control ◽  
Different Temperatures ◽  
Damage Process

Laboratory investigations of relaxation damage properties of high viscosity asphalt sand (HVAS) by uniaxial compression tests and modified generalized Maxwell model (GMM) to simulate viscoelastic characteristics coupling damage were carried out. A series of uniaxial compression relaxation tests were performed on HVAS specimens at different temperatures, loading rates, and constant levels of input strain. The results of the tests show that the peak point of relaxation modulus is highly influenced by the loading rate in the first half of an L-shaped curve, while the relaxation modulus is almost constant in the second half of the curve. It is suggested that for the HVAS relaxation tests, the temperature should be no less than −15°C. The GMM is used to determine the viscoelastic responses, the Weibull distribution function is used to characterize the damage of the HVAS and its evolution, and the modified GMM is a coupling of the two models. In this paper, the modified GMM is implemented through a secondary development with the USDFLD subroutine to analyze the relaxation damage process and improve the linear viscoelastic model in ABAQUS. Results show that the numerical method of coupling damage provides a better approximation of the test curve over almost the whole range. The results also show that the USDFLD subroutine can effectively predict the relaxation damage process of HVAS and can provide a theoretical support for crack control of asphalt pavements.

scholarly journals A New Viscoelasticity Dynamic Fitting Method Applied for Polymeric and Polymer-Based Composite Materials

Materials ◽  
2020 ◽  
Vol 13 (22) ◽  
pp. 5213
Author(s):  
Vitor Dacol ◽  
Elsa Caetano ◽  
João Correia
Keyword(s):  
Composite Materials ◽  
Dynamic Behaviour ◽  
Creep Compliance ◽  
Complex Modulus ◽  
Relaxation Modulus ◽  
Viscoelastic Behaviour ◽  
Harmonic Load ◽  
Load Case ◽  
Accurate Analysis ◽  
Complex Moduli

The accurate analysis of the behaviour of a polymeric composite structure, including the determination of its deformation over time and also the evaluation of its dynamic behaviour under service conditions, demands the characterisation of the viscoelastic properties of the constituent materials. Linear viscoelastic materials should be experimentally characterised under (i) constant static load and/or (ii) harmonic load. In the first load case, the viscoelastic behaviour is characterised through the creep compliance or the relaxation modulus. In the second load case, the viscoelastic behaviour is characterised by the complex modulus, E*, and the loss factor, η. In the present paper, a powerful and simple implementing technique is proposed for the processing and analysis of dynamic mechanical data. The idea is to obtain the dynamic moduli expressions from the Exponential-Power Law Method (EPL) of the creep compliance and the relaxation modulus functions, by applying the Carson and Laplace transform functions and their relationship to the Fourier transform, and the Theorem of Moivre. Reciprocally, once the complex moduli have been obtained from a dynamic test, it becomes advantageous to use mathematical interconversion techniques to obtain the time-domain function of the relaxation modulus, E(t), and the creep compliance, D(t). This paper demonstrates the advantages of the EPL method, namely its simplicity and straightforwardness in performing the desirable interconversion between quasi-static and dynamic behaviour of polymeric and polymer-composite materials. The EPL approximate interconversion scheme to convert the measured creep compliance to relaxation modulus is derived to obtain the complex moduli. Finally, the EPL Method is successfully assessed using experimental data from the literature.

scholarly journals Effect of Preservation Period on the Viscoelastic Material Properties of Soft Tissues With Implications for Liver Transplantation

2010 ◽  
Vol 132 (10) ◽  
Author(s):  
Sina Ocal ◽  
M. Umut Ozcan ◽  
Ipek Basdogan ◽  
Cagatay Basdogan
Keyword(s):  
Liver Transplantation ◽  
Viscoelastic Material ◽  
Material Properties ◽  
Soft Tissues ◽  
Excitation Frequency ◽  
Viscoelastic Model ◽  
Relaxation Modulus ◽  
Bovine Liver ◽  
Dynamic Responses ◽  
Time Dependent

The liver harvested from a donor must be preserved and transported to a suitable recipient immediately for a successful liver transplantation. In this process, the preservation period is the most critical, since it is the longest and most tissue damage occurs during this period due to the reduced blood supply to the harvested liver and the change in its temperature. We investigate the effect of preservation period on the dynamic material properties of bovine liver using a viscoelastic model derived from both impact and ramp and hold experiments. First, we measure the storage and loss moduli of bovine liver as a function of excitation frequency using an impact hammer. Second, its time-dependent relaxation modulus is measured separately through ramp and hold experiments performed by a compression device. Third, a Maxwell solid model that successfully imitates the frequency- and time-dependent dynamic responses of bovine liver is developed to estimate the optimum viscoelastic material coefficients by minimizing the error between the experimental data and the corresponding values generated by the model. Finally, the variation in the viscoelastic material coefficients of bovine liver are investigated as a function of preservation period for the liver samples tested 1 h, 2 h, 4 h, 8 h, 12 h, 24 h, 36 h, and 48 h after harvesting. The results of our experiments performed with three animals show that the liver tissue becomes stiffer and more viscous as it spends more time in the preservation cycle.

An improved numerical interconversion for creep compliance and relaxation modulus

1972 ◽  
Vol 16 (11) ◽  
pp. 2963-2972 ◽  
Author(s):  
Warren F. Knoff ◽  
Irving L. Hopkins
Keyword(s):  
Creep Compliance ◽  
Relaxation Modulus

scholarly journals Relation Between Relaxation Modulus and Creep Compliance for Nonlinear Power Law model

1979 ◽  
Vol 7 (1) ◽  
pp. 15-19
Author(s):  
Takuii YAMAGUCHI ◽  
Hiroshi KIMURA
Keyword(s):  
Power Law ◽  
Creep Compliance ◽  
Relaxation Modulus ◽  
Power Law Model
Sign in / Sign up

Export Citation Format

Share Document