Effects of operational parameters on defluoridation efficiency using electrocoagulation process

2011 ◽  
Vol 6 (1) ◽  
Author(s):  
M. Behbahani ◽  
M.R. Alavi Moghaddam ◽  
M. Arami
Keyword(s):  
Reaction Time ◽  
Anode Material ◽  
Removal Efficiency ◽  
Fluoride Concentration ◽  
Fluoride Removal ◽  
Operational Parameters ◽  
Applied Current ◽  
Initial Ph ◽  
Electrocoagulation Process ◽  
Electrode Connection

The aim of this study is to examine the effect of operational parameters on fluoride removal using electrocoagulation method. For this purpose, various operational parameters including initial pH, initial fluoride concentration, applied current, reaction time, electrode connection mode, anode material, electrolyte salt, electrolyte concentration, number of electrodes and interelectrode distance were investigated. The highest defluoridation efficiency achieved at initial pH 6. In the case of initial fluoride concentration, maximum removal efficiency (98.5%) obtained at concentration of 25mg/l. The increase of applied current and reaction time improved defluoridation efficiency up to 99%. The difference of fluoride removal efficiencies between monopolar and bipolar series and monopolar parallel were significant, especially at reaction time of 5 min. When aluminum used as anode material, higher removal efficiency (98.5%) achieved compared to that of iron anode (67.7%). The best electrolyte salt was NaCl with the maximum defluoridation efficiency of 98.5% compared to KNO3 and Na2SO4. The increase of NaCl had no effect on defluoridation efficiency. Number of electrodes had little effect on the amounts of Al3+ ions released in the solution and as a result defluoridation efficiency. Almost the same fluoride removal efficiency obtained for different interelectrode distances.

scholarly journals Eggshell-Derived Nanohydroxyapatite Adsorbent for Defluoridation of Drinking Water from Bofo of Ethiopia

2019 ◽  
Vol 2019 ◽  
pp. 1-12 ◽  
Author(s):  
Kifle Workeneh ◽  
Enyew Amare Zereffa ◽  
Toshome Abdo Segne ◽  
Rajalakshmanan Eswaramoorthy
Keyword(s):  
Removal Efficiency ◽  
Fluoride Concentration ◽  
Fluoride Removal ◽  
Batch Adsorption ◽  
Alternative Source ◽  
Fluoride Adsorption ◽  
Initial Ph ◽  
Pseudo Second Order ◽  
Ft Ir ◽  
Eggshell Waste

Fluoride has become a notable toxicological environmental hazard worldwide because it is often found in groundwater. In the present study, hydroxyapatite adsorbent was synthesized from eggshell waste to remove fluoride from aqueous solution. XRD, FT-IR, and TGA techniques were used to characterize the prepared adsorbent. Batch adsorption studies were performed to examine the adsorption capacity of hydroxyapatite such as the effect of the initial pH of the solution, contact time, adsorbent dose, and initial fluoride concentration. The fluoride ion-selective electrode was used to determine the fluoride removal efficiency. 98.8% of fluoride was removed at pH 3.0, but at pH ~7.0, 85% of fluoride was removed; it shows that the fluoride adsorption is pH dependent. The adsorption isotherm studies (Langmuir and Freundlich models) and the experimental results for the removal of fluoride showed that the Langmuir model was more favorable and the reaction followed pseudo-second-order kinetics. In real water samples, the prepared hydroxyapatite derived from eggshell exhibited 81% removal efficiency. Our results indicate that eggshell waste-derived hydroxyapatite may be an alternative source for defluoridation in developing countries.

scholarly journals Application of Electrocoagulation Process Using Iron and Aluminum Electrodes for Fluoride Removal from Aqueous Environment

2012 ◽  
Vol 9 (4) ◽  
pp. 2297-2308 ◽  
Author(s):  
Edris Bazrafshan ◽  
Kamal Aldin Ownagh ◽  
Amir Hossein Mahvi
Keyword(s):  
Removal Efficiency ◽  
Fluoride Concentration ◽  
Electrical Potential ◽  
Cost Effective ◽  
Fluoride Removal ◽  
Aqueous Environment ◽  
Treatment Rate ◽  
Effective Removal ◽  
Electrocoagulation Process ◽  
Aluminum Electrodes

Fluoride in drinking water above permissible level is responsible for human being affected by skeletal fluorosis. The present study was carried out to assess the ability of electrocoagulation process with iron and aluminum electrodes in order to removal of fluoride from aqueous solutions. Several working parameters, such as fluoride concentration, pH, applied voltage and reaction time were studied to achieve a higher removal capacity. Variable concentrations (1, 5 and 10 mg L-1) of fluoride solutions were prepared by mixing proper amount of sodium fluoride with deionized water. The varying pH of the initial solution (3, 7 and 10) was also studied to measure their effects on the fluoride removal efficiency. Results obtained with synthetic solution revealed that the most effective removal capacities of fluoride could be achieved at 40 V electrical potential. In addition, the increase of electrical potential, in the range of 10-40 V, enhanced the treatment rate. Also comparison of fluoride removal efficiency showed that removal efficiency is similar with iron and aluminum electrodes. Finally it can be concluded that the electrocoagulation process has the potential to be utilized for the cost-effective removal of fluoride from water and wastewater.

The treatment of zinc-cyanide electroplating rinse water using an electrocoagulation process

2013 ◽  
Vol 68 (10) ◽  
pp. 2220-2227 ◽  
Author(s):  
Elif Senturk
Keyword(s):  
Electrode Material ◽  
Operating Time ◽  
Operating Conditions ◽  
Optimum Operating ◽  
Operating Parameters ◽  
Initial Ph ◽  
Electrocoagulation Process ◽  
Removal Efficiencies ◽  
Rinse Water ◽  
Electrode Connection

This paper investigates the treatment of zinc-cyanide electroplating rinse water using an electrocoagulation process (ECP). The effects of operating parameters such as electrode material, current density (2.5–40 A/m2), operating time (0–60 min), initial pH (5–12) and electrode connection mode (monopolar parallel (MP-P), monopolar series and bipolar series) on the ECP were evaluated to find the optimum operating conditions. At 20 A/m2, 60 min, the highest removal efficiencies were obtained with 85 and 99% for Fe and 64 and 33% for Al electrodes, for cyanide and zinc, respectively. The optimum operating conditions were found to be 30 A/m2 and 40 min, for the Fe electrode at the original pH (9.5) of the rinse water. Considering efficiency and economy, the MP-P connection mode was determined as the optimum connection mode.

scholarly journals Fluoride removal efficiencies of Al-EC and Fe-EC reactors: process optimization using Box–Behnken design of the surface response methodology

2020 ◽  
Vol 10 (9) ◽  
Author(s):  
Magori J. Nyangi ◽  
Yonas Chebude ◽  
Kessy F. Kilulya
Keyword(s):  
Treatment Time ◽  
Fluoride Concentration ◽  
Fluoride Removal ◽  
Reactor Model ◽  
Optimal Operating ◽  
Surface Response Methodology ◽  
Box Behnken Design ◽  
Surface Response ◽  
Independent Variables ◽  
Initial Ph

Abstract In this study, surface response methodology was employed to investigate the effect of different interacting factors on the removal of fluoride from synthetic water using aluminum electrocoagulation (Al-EC) and iron electrocoagulation (Fe-EC) in different reactors. Box–Behnken design of a Design Expert version 11 was used for the optimization and evaluation of the process independent variables: applied electric density, initial pH, initial fluoride concentration and treatment time on the efficiency of fluoride removal as a response. Results showed that the effect of current density and initial fluoride concentration was significant model terms for fluoride reduction in Fe-EC and Al-EC reactors, respectively. The Al-EC reactor model presented the R2 value of 79.2% while Fe-EC presented R2 value of 75.8%, showing that both models can predict the response well. The reduction by 94% (initial concentration of 16 mgF/L) was established at optimal operating parameters of 18.5 mAcm−2, pH 6.80 in 50 min using Al-EC. On the other hand, 16 mgF/L was reduced by 92% to 1.28 mgF/L in Fe-EC reactor at optimal condition of 6.5 mAcm−2, pH 6.50 in 50 min. Experimental results correlated well to the model predicted results that were 95 and 94% for Al-EC and Fe-EC, respectively. Both reactors manage to reduce fluoride to a level recommended by WHO (≤ 1.5 mg/L) for drinking purpose.

scholarly journals Application of Electrocoagulation for the Removal of Color from Institutional Wastewater: Analysis with Response Surface Methodology

2021 ◽  
Vol 9 (2) ◽  
pp. 470-479
Keyword(s):  
Response Surface Methodology ◽  
Reaction Time ◽  
Response Surface ◽  
The Other ◽  
Quadratic Model ◽  
Operational Parameters ◽  
Electrode Combination ◽  
Electrocoagulation Process ◽  
Percentage Removal ◽  
Central Composite

The removal percentage of color from institutional wastewater was studied using an electrocoagulation process with different electrode combination at the anode and cathode. This was done by considering operational parameters such as pH at (3, 6 and 9), current at (0.03A, 0.06A and 0.09A) and reaction time at (20, 40 and 60 minutes). When electrode combined in the form of Al-Al (anode-Cathode/Cathode-Anode) and Fe-Fe (anode-Cathode/Cathode-Anode) the percentage removal of color was up to 95.50% and 97.24% respectively. On the other hand around 98.03% and 91.95% of color was removed when Al-Fe (Anode-Cathode) and Fe-Al (Anode-Cathode) combined at pH 9 and 60 minutes of reaction time respectively. Central composite design from response surface methodology was used up to analysis the statistical and mathematical data based on experimental results such as the model was significant for all electrode combinations. Similarly a quadratic model was used for further study of operational effects on the removal (%) of color from institutional wastewater. The value of coefficient of the determination (R2) also indicated the model was a good fit as well as optimization was done by Response Surface Methodology.

scholarly journals An Experimental Study of Fluoride Removal from Wastewater by Mn-Ti Modified Zeolite

Water ◽  
2021 ◽  
Vol 13 (23) ◽  
pp. 3343
Author(s):  
Bo Yang ◽  
Guirong Sun ◽  
Bingxu Quan ◽  
Jiawei Tang ◽  
Chunhui Zhang ◽  
...  
Keyword(s):  
Sensitivity Analysis ◽  
Removal Efficiency ◽  
Natural Zeolite ◽  
Fluoride Concentration ◽  
Current Work ◽  
Fluoride Removal ◽  
Metal Fluoride ◽  
Modified Zeolite ◽  
X Ray ◽  
Independent Variables

The emerging interest in fluoride-removal from wastewater has attracted attention to zeolite since it has been considered as a natural adsorbent. However, the fluoride-removal efficiency of natural zeolite is generally low. As part of the effort to improve the zeolite adsorption efficiency, we have produced and tested the Mn-Ti modified zeolite. In the current work, the material preparation is discussed, and prepared materials were characterized by X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDS), scanning electron microscopy, and Fourier transform infrared (FTIR) spectra. Both static and dynamic experiments were conducted to examine the effects of independent variables. In the static adsorption section, sensitivity analysis experiments were conducted for independent variables, such as adsorbent dosage, pH, temperature, and competitive ions. The maximum adsorption capacity is 2.175 mg/g, which was obtained at PH = 7, temperature = 25 °C, and initial fluoride concentration = 10 mg/L. For adsorption kinetics, both Lagergren and Pseudo-second order models predict the experiments very well, which probably demonstrates that the current process is a combination of physical sorption and chemisorption. For adsorption isotherms, the Freundlich model performs better than the Langmuir model since it is usually applied to illustrate adsorption on inhomogeneous surfaces. In the dynamic adsorption section, sensitivity analysis experiments were also conducted for independent variables, such as adsorbent thickness, flow velocity, initial fluoride concentration, and PH. Additionally, the adsorption mechanism is also discussed. The main reason is the hydrated metal fluoride precipitate formation. As we know, the current work provides the first quantified comparison of the natural zeolite and the Mn-Ti modified zeolite regarding fluoride-removal efficiency.

scholarly journals Removal Efficiency of Acid Red 18 Dye from Aqueous Solution Using Different Aluminium-Based Electrode Materials by Electrocoagulation Process

2020 ◽  
Vol 20 (3) ◽  
pp. 536
Author(s):  
Nurulhuda Amri ◽  
Ahmad Zuhairi Abdullah ◽  
Suzylawati Ismail
Keyword(s):  
Reaction Time ◽  
Removal Efficiency ◽  
Industrial Wastewater ◽  
Electrode Materials ◽  
Cost Effective ◽  
Aluminium Electrode ◽  
Electrocoagulation Process ◽  
Commercial Aluminium ◽  
A Current ◽  
Better Than

This work compares commercial aluminium electrode for use in the treatment of wastewater by electrocoagulation process against waste aluminium cans electrode. The applicability of the waste aluminium cans electrode was tested for decolorization of Acid Red 18 dye as a model pollutant. The batch electrocoagulation process using both types of electrode was conducted at a current density of 25 mA/cm2, a pH of 3, an initial concentration of 100 mg/L and 25 min of reaction time. The elemental composition and surface morphology of both electrode materials and the sludge produced were analyzed using SEM-EDX to establish the correlation between the properties and characteristics of both electrode materials with their dye removal performance. The results demonstrated that waste aluminium cans performed better than commercial aluminium electrode with a removal efficiency of 100% in 25 min of reaction time. This was due to the higher Al dissolution of waste aluminium cans electrode that contributed to the larger amount of Al3+ released into the solution to consequently form more flocs to remove the dye molecules. In conclusion, the proposed waste aluminium electrode was considered as efficient and cost-effective and had the potential to replace the conventional ones in treating colored industrial wastewater using electrocoagulation process.

scholarly journals Removal of Cadmium from Industrial Wastewater using Electrocoagulation Process

2019 ◽  
Vol 26 (1) ◽  
pp. 24-34 ◽  
Author(s):  
Mohammed Alameen Salem ◽  
Najwa Majeed
Keyword(s):  
Heavy Metal ◽  
Removal Efficiency ◽  
Applied Voltage ◽  
Industrial Wastewater ◽  
Batch Reactor ◽  
Operating Parameters ◽  
Initial Concentration ◽  
Initial Ph ◽  
Electrocoagulation Process ◽  
Aluminum Electrodes

Cadmium is one of the heavy metal found in the wastewater of many industries. The electrocoagulation offers many advantages for the removal of cadmium over other methods. So the removal of cadmium from wastewater by using electrocoagulation was studied to investigate the effect of operating parameters on the removal efficiency. The studied parameters were the initial pH, initial concentration, and applied voltage. The study experiments were conducted in a batch reactor with  with two pairs of aluminum electrodes with dimension  and 2mm in thick with 1.5 cm space between them. The optimum removal was obtained at pH =7, initial concentration = 50 mg/L, and applied voltage = 20 V and it was 90%.

scholarly journals Optimization of electrocoagulation process parameters for enhancing phosphate removal in a biofilm-electrocoagulation system

2021 ◽  
Author(s):  
Jie Zeng ◽  
Min Ji ◽  
Yingxin Zhao ◽  
Pedersen ◽  
Thomas Helmer ◽  
...  
Keyword(s):  
Reaction Time ◽  
Removal Efficiency ◽  
Operating Cost ◽  
Integrated System ◽  
Phosphate Removal ◽  
Electrode Distance ◽  
Electrocoagulation Process ◽  
Biofilm Process ◽  
Switching Mode ◽  
The Individual

Abstract This study aimed to enhance the removal of phosphate in synthetic rural sewage by using a continuous electrocoagulation combined with biofilm process in an integrated system. Characteristic indexes of biofilm process effluent covering pH, DO, SS, COD and phosphate maintained a narrow fluctuation range and tended not readily to influence the phosphate removal of subsequent electrocoagulation. Three parameters including inter-electrode distance, current intensity and reaction time were selected to investigate the performance of enhancing phosphate removal. On the strength of single-factor tests, the Box-Behnken design (BBD) coupled with response surface methodology (RSM) was applied to investigate the individual and mutual interaction impacts of the major operating parameters and to optimize conditions. The optimum conditions were found to be inter-electrode distance of 1.8 cm, current density of 2.1 mA/cm2 and EC reaction time of 34 min, and the phosphate removal efficiency was achieved to be 90.24% along with less than 1 mg/L in case of periodic polarity switching mode, which raised removal efficiency by 10.10% and reduced operating cost by 0.13 CNY/g PO4− compared to non-switching mode. The combination of biofilm processing and electrocoagulation treatment was proven a valid and feasible method for enhancing phosphate removal.

scholarly journals Modeling and optimization of a continuous electrocoagulation process using an artificial intelligence approach

2021 ◽  
Author(s):  
Nuno S. Graça ◽  
Ana M. Ribeiro ◽  
Alírio E. Rodrigues
Keyword(s):  
Operating Cost ◽  
Fluoride Concentration ◽  
Fluoride Removal ◽  
Optimal Conditions ◽  
Feed Concentration ◽  
Predictive Capacity ◽  
Electrocoagulation Process ◽  
Artificial Neural Network Ann ◽  
Hidden Layer ◽  
Intelligence Approach

Abstract An artificial neural network (ANN) with the topology 8-94-85-2 (input – hidden layer 1 - hidden layer 2 - output) was used to model the operation of the continuous electrocoagulation (CEC) process for the removal of fluoride from water. After the ANN training, the sum of the squared errors (MSE) and the determination coefficient (R2) of the testing set model predictions were 0.0088 and 0.999, respectively, showing a good generalization and model's predictive capacity. The optimization of the process cost using the genetic algorithm (GA) showed that the optimal conditions are highly dependent on the feed concentration and the fluoride removal requirements. For a 5 L of water containing 10 mg/L of fluoride, the optimal conditions to reduce the fluoride concentration below the permissible limit (1.5 mg/L) are 88.3 mA of current intensity, a flow rate of 73.6 mL/min, and the use of a series monopolar (SM) electrode configuration, corresponding to a fluoride removal of 85% and an operating cost of 0.05 €/L.

Sign in / Sign up

Export Citation Format

Share Document