scholarly journals Eggshell-Derived Nanohydroxyapatite Adsorbent for Defluoridation of Drinking Water from Bofo of Ethiopia

2019 ◽  
Vol 2019 ◽  
pp. 1-12 ◽  
Author(s):  
Kifle Workeneh ◽  
Enyew Amare Zereffa ◽  
Toshome Abdo Segne ◽  
Rajalakshmanan Eswaramoorthy
Keyword(s):  
Removal Efficiency ◽  
Fluoride Concentration ◽  
Fluoride Removal ◽  
Batch Adsorption ◽  
Alternative Source ◽  
Fluoride Adsorption ◽  
Initial Ph ◽  
Pseudo Second Order ◽  
Ft Ir ◽  
Eggshell Waste

Fluoride has become a notable toxicological environmental hazard worldwide because it is often found in groundwater. In the present study, hydroxyapatite adsorbent was synthesized from eggshell waste to remove fluoride from aqueous solution. XRD, FT-IR, and TGA techniques were used to characterize the prepared adsorbent. Batch adsorption studies were performed to examine the adsorption capacity of hydroxyapatite such as the effect of the initial pH of the solution, contact time, adsorbent dose, and initial fluoride concentration. The fluoride ion-selective electrode was used to determine the fluoride removal efficiency. 98.8% of fluoride was removed at pH 3.0, but at pH ~7.0, 85% of fluoride was removed; it shows that the fluoride adsorption is pH dependent. The adsorption isotherm studies (Langmuir and Freundlich models) and the experimental results for the removal of fluoride showed that the Langmuir model was more favorable and the reaction followed pseudo-second-order kinetics. In real water samples, the prepared hydroxyapatite derived from eggshell exhibited 81% removal efficiency. Our results indicate that eggshell waste-derived hydroxyapatite may be an alternative source for defluoridation in developing countries.

scholarly journals Removal of Fluoride from Drinking Water Using Modified Immobilized Activated Alumina

2013 ◽  
Vol 2013 ◽  
pp. 1-7 ◽  
Author(s):  
Aneeza Rafique ◽  
M. Ali Awan ◽  
Ayesha Wasti ◽  
Ishtiaq A. Qazi ◽  
Muhammad Arshad
Keyword(s):  
Drinking Water ◽  
Removal Efficiency ◽  
Activated Charcoal ◽  
Contact Time ◽  
Sol Gel ◽  
Fluoride Concentration ◽  
Fluoride Removal ◽  
Batch Adsorption ◽  
Activated Alumina ◽  
Fluoride Adsorption

The study describes the removal of fluoride from drinking water using modified immobilized activated alumina (MIAA) prepared by sol-gel method. The modification was done by adding a specific amount of alum during the sol formation step. The fluoride removal efficiency of MIAA was 1.35 times higher as compared to normal immobilized activated alumina. A batch adsorption study was performed as a function of adsorbent dose, contact time, stirring rate, and initial fluoride concentration. More than 90% removal of fluoride was achieved within 60 minutes of contact time. The adsorption potential of MIAA was compared with activated charcoal which showed that the removal efficiency was about 10% more than the activated charcoal. Both the Langmuir and Freundlich adsorption isotherms fitted well for the fluoride adsorption on MIAA with the regression coefficientR2of 0.99 and 0.98, respectively. MIAA can both be regenerated thermally and chemically. Adsorption experiments using MIAA were employed on real drinking water samples from a fluoride affected area. The study showed that modified immobilized activated alumina is an effective adsorbent for fluoride removal.

Effects of operational parameters on defluoridation efficiency using electrocoagulation process

2011 ◽  
Vol 6 (1) ◽  
Author(s):  
M. Behbahani ◽  
M.R. Alavi Moghaddam ◽  
M. Arami
Keyword(s):  
Reaction Time ◽  
Anode Material ◽  
Removal Efficiency ◽  
Fluoride Concentration ◽  
Fluoride Removal ◽  
Operational Parameters ◽  
Applied Current ◽  
Initial Ph ◽  
Electrocoagulation Process ◽  
Electrode Connection

The aim of this study is to examine the effect of operational parameters on fluoride removal using electrocoagulation method. For this purpose, various operational parameters including initial pH, initial fluoride concentration, applied current, reaction time, electrode connection mode, anode material, electrolyte salt, electrolyte concentration, number of electrodes and interelectrode distance were investigated. The highest defluoridation efficiency achieved at initial pH 6. In the case of initial fluoride concentration, maximum removal efficiency (98.5%) obtained at concentration of 25mg/l. The increase of applied current and reaction time improved defluoridation efficiency up to 99%. The difference of fluoride removal efficiencies between monopolar and bipolar series and monopolar parallel were significant, especially at reaction time of 5 min. When aluminum used as anode material, higher removal efficiency (98.5%) achieved compared to that of iron anode (67.7%). The best electrolyte salt was NaCl with the maximum defluoridation efficiency of 98.5% compared to KNO3 and Na2SO4. The increase of NaCl had no effect on defluoridation efficiency. Number of electrodes had little effect on the amounts of Al3+ ions released in the solution and as a result defluoridation efficiency. Almost the same fluoride removal efficiency obtained for different interelectrode distances.

scholarly journals REMOVAL OF FLUORIDE USING NEEM LEAVES BATCH REACTOR: KINETICS AND EQUILIBRIUM STUDIES

2018 ◽  
Vol 11 (3) ◽  
pp. 237
Author(s):  
Tej Pratap Singh ◽  
Majumder Cb
Keyword(s):  
Removal Efficiency ◽  
Batch Reactor ◽  
Low Cost ◽  
Fluoride Concentration ◽  
Second Order ◽  
Fluoride Removal ◽  
Equilibrium Studies ◽  
Neem Leaves ◽  
Pseudo Second Order ◽  
Adsorbent Dose

 Objective: The aim of this paper is to study the fluoride removal efficiency of the neem leaves low-cost biosorbent for defluoridation of sewage wastewater.Methods: For finding the best operating condition for maximum removal of fluoride, batchwise experiments were performed at different contact times and keeping other parameters to be constant such as pH, initial fluoride concentration, and adsorbent dose. Various kinetic models such as intraparticle diffusion model, Bangham’s model, and Elovich model had been investigated for determining the suitable adsorption mechanism. The rate of adsorption of fluoride on neem leaves has been determined by pseudo-first-order and pseudo-second-order rate models.Results: The adsorption kinetics rate and mechanism was best described by the pseudo-second-order model and Bangham’s model, respectively. The optimum pH, initial concentration, adsorbent dose, and contact time were found to be 7, 20 mg/L, 10 g/L, and 40 min, respectively, for which there was maximum fluoride removal.Conclusion: The result obtained from the experiments show that the neem leaves have been proved to be a low-cost biosorbent for the defluoridation of the sewage wastewater and have high fluoride removal efficiency.

scholarly journals Application of Novel Clay Composite Adsorbent for Fluoride Removal

2019 ◽  
Vol 16 (2) ◽  
pp. 164-173 ◽  
Author(s):  
Lechisa Daba Gidi ◽  
Enyew Zereffa Amare ◽  
H C Ananda Murthy ◽  
Buzuayehu Abebe
Keyword(s):  
Removal Efficiency ◽  
Volume Ratio ◽  
Cost Effective ◽  
Xrd Analysis ◽  
Fluoride Removal ◽  
Clay Material ◽  
Composite Adsorbent ◽  
Pseudo Second Order ◽  
Ft Ir ◽  
Ir Analysis

A novel cost-effective, eco-friendly clay composite adsorbent was developed towards fluoride remediation. Clay, Grog, Bone char, and Sawdust were dry mixed within volume ratios of (5:1:1:1), (4:2:2:1), and (3:3:3:1), respectively. The powders were mixed again with distilled water, pressed with disc shape; sun dried for three days and fired for one hour in the muffle furnace at 400oC, 500oC, and 600oC. The cooled discs were ground and sieved to obtain nine different composite powdered with particle size less than 1.18 mm. The developed composite adsorbent was characterized using advanced techniques: XRD, SEM, and FT-IR. The adsorption studies showed that among the developed adsorbents, composite with the volume ratio of (3:3:3:1) and optimized at firing temperature of 400°C exhibited maximum adsorption capacities of 91.6% fluoride removal efficiency. The XRD analysis revealed mixed phases in the composite, and the presence of OH¯ functional groups was indicated by FT-IR analysis. The experimental results indicated that the Langmuir model was found to fit better for the removal of fluoride ion and followed the pseudo-second-order rate equation. The composite clay material exhibited excellent removal efficiency for the real water samples analyzed.

scholarly journals Development of a novel Artemia eggshell-zirconium nanocomposite for efficient fluoride removal

PLoS ONE ◽  
2021 ◽  
Vol 16 (1) ◽  
pp. e0244711
Author(s):  
Wen Zhang ◽  
Yuqin Mao ◽  
Yin Lu
Keyword(s):  
Composite Material ◽  
Removal Efficiency ◽  
Treatment Time ◽  
Fluoride Concentration ◽  
Fluoride Removal ◽  
Pore Blockage ◽  
Pseudo Second Order ◽  
The Common ◽  
Kinetics Of ◽  
Better Than

Fluoride pollution in water has attracted widespread concern worldwide. In this study, an Artemia eggshell-zirconium (Aes-Z) nanocomposite has been used for fluoride removal. Material characterization results showed that nano-ZrO2 was immobilized on the inner surface of the Artemia eggshell, and there was no pore blockage on the composite material. Various parameters influencing on the fluoride removal, including treatment time, composite dosage, pH, initial fluoride concentration, and other anions, were analyzed. The removal efficiency of the composite material was better than that of the single zirconia material. The removal percentage of fluoride reached 93% in 30 min with an initial fluoride concentration of 10 mg/L and a nanocomposite dosage of 8.0 g/L. The composite material had a high removal efficiency for fluoride in the pH region 4.0–10.0. The adsorption of fluoride was not influenced by the common anions (e.g., Cl-, SO42-, and NO3-) in water. The regeneration revealed that the Aes-Z composite material could be reused and remove fluoride effectively in four cycles. The pseudo-second-order rate model adequately represented the adsorption kinetics of the Aes-Z composite material. A possible, defluoridation mechanism of the Aes-Z composite material was also proposed. This study demonstrates that Aes-Z is a promising adsorbent material for fluoride removal.

scholarly journals Fluoride Adsorption by Pumice from Aqueous Solutions

2012 ◽  
Vol 9 (4) ◽  
pp. 1843-1853 ◽  
Author(s):  
Amir Hossein Mahvi ◽  
Behzad Heibati ◽  
Alireza Mesdaghinia ◽  
Ahmad Reza Yari
Keyword(s):  
Drinking Water ◽  
Aqueous Solutions ◽  
Fluoride Concentration ◽  
Freundlich Isotherm ◽  
Fluoride Removal ◽  
Maximum Sorption Capacity ◽  
Fluoride Adsorption ◽  
Maximum Sorption ◽  
Pseudo Second Order ◽  
High Concentrations

Drinking water provides many vital elements for the human body, but the presence of some dissolved elements more than permissible concentration can endanger human health. Among the dissolved elements in drinking water, fluoride is noticeable, because both the very low or very high concentrations have adverse health impacts such as dental caries. Therefore, fluoride concentration should be kept in acceptable levels. In this study Pumice was used for fluoride removal. It was found that Fluoride sorption kinetic was fitted by pseudo-second-order model. The maximum sorption capacity of Pumice was found to be 13.51 mg/g at laboratory temperature (24°C). Maximum sorption study occurred at pH= 3. Results of Isotherm showed the fluoride sorption has been well fitted with Freundlich isotherm model. This study has demonstrated that Pumice can be used as effective adsorbents for fluoride removal from aqueous solutions. The adsorbent prepared in this study was cheap and efficient in removal of fluoride than other adsorbents.

Synthesis of Functionalized Magnetite Titanium Dioxide Nanocomposite for Removal of Acid Fuchsine Dye

2018 ◽  
Vol 21 (8) ◽  
pp. 583-593 ◽  
Author(s):  
Sara Rahnama ◽  
Shahab Shariati ◽  
Faten Divsar
Keyword(s):  
Titanium Dioxide ◽  
Removal Efficiency ◽  
Magnetic Core ◽  
Fractional Factorial ◽  
Order Kinetic ◽  
Sorption Data ◽  
Salt Addition ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Ft Ir

Objective: In this research, a novel magnetite titanium dioxide nanocomposite functionalized by amine groups (Fe3O4@SiO2@TiO2-NH2) was synthesized and its ability for efficient removal of Acid Fuchsine as an anionic dye from aqueous solutions was investigated. Method: The core-shell structure of Fe3O4@SiO2@TiO2 was prepared using Fe3O4 as magnetic core, tetra ethyl orthosilicate as silica and tetra butyl titanate as titanium source for shell. The synthesized nanocomposites (particle size lower than 44 nm) were characterized by FT-IR, XRD, DRS, SEM and TGA instruments. The various experimental parameters affecting dye removal efficiency were investigated and optimized using Taguchi fractional factorial design. Results: The synthesized adsorbent showed the highest removal efficiency of Acid Fuchsine (99 %) at pH= 3.5, without salt addition and during stirring at contact times less than 10 minutes. The study of kinetic models at two concentration levels showed the fast dye sorption on the surface of proposed nanocomposites with pseudo second order kinetic model (R2=1). Also, the fitting of Acid Fuchsine sorption data to Freundlich, Langmuir and Temkin isotherms suggested that Freundlich model gave a better fitting than other models (R2=0.9936, n=2). Conclusion: Good chemical stability, excellent magnetic properties, very fast adsorption kinetics and high removal efficiency make the synthesized nanocomposite as a proper recoverable sorbent for removal of Acid Fuchsine dye from wastewaters.

scholarly journals Eggshell Powder as an Adsorbent for Removal of Fluoride from Aqueous Solution: Equilibrium, Kinetic and Thermodynamic Studies

2012 ◽  
Vol 9 (3) ◽  
pp. 1457-1480 ◽  
Author(s):  
R. Bhaumik ◽  
N. K. Mondal ◽  
B. Das ◽  
P. Roy ◽  
K. C. Pal ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Adsorption Process ◽  
Low Cost ◽  
Fluoride Removal ◽  
Contaminated Water ◽  
Fluoride Adsorption ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Kinetic And Thermodynamic Studies ◽  
Maximum Removal

A new medium, eggshell powder has been developed for fluoride removal from aqueous solution. Fluoride adsorption was studied in a batch system where adsorption was found to be pH dependent with maximum removal efficiency at 6.0. The experimental data was more satisfactorily fitted with Langmuir isotherm model. The kinetics and the factor controlling adsorption process fully accepted by pseudo-second-order model were also discussed. Eawas found to be 45.98 kJmol-1by using Arrhenius equation, indicating chemisorption nature of fluoride onto eggshell powder. Thermodynamic study showed spontaneous nature and feasibility of the adsorption process with negative enthalpy (∆H0) value also supported the exothermic nature. Batch experiments were performed to study the applicability of the adsorbent by using fluoride contaminated water collected from affected areas. These results indicate that eggshell powder can be used as an effective, low-cost adsorbent to remove fluoride from aqueous solution as well as groundwater.

scholarly journals Biosorption of Fluoride from Synthetic and Ground Water Using Chlorella vulgaris Immobilized in Calcium Alginate Beads in an Upflow Packed Bed Column

2017 ◽  
Vol 61 (3) ◽  
pp. 188 ◽  
Author(s):  
Poornima G. Hiremath ◽  
Thomas Theodore
Keyword(s):  
Experimental Data ◽  
Ground Water ◽  
Chlorella Vulgaris ◽  
Water Samples ◽  
Packed Column ◽  
Fluoride Concentration ◽  
Fixed Bed ◽  
Fluoride Removal ◽  
Fluoride Ions ◽  
Fluoride Adsorption

The potential of immobilized Chlorella vulgaris to remove fluoride from synthetic and real ground water samples in a fixed bed was investigated. The effect of important kinetic parameters including column bed height, feed flow rate and influent fluoride concentration of solution on fluoride removal was studied. Thomas, Yoon-Nelson, and BDST models were used to analyze the experimental data and understand the influence on biosorption performance. The models’ predictions were in good agreement with the experimental data for all the process parameters studied, indicating that the models were suitable for fixed-bed column design. Fluoride adsorption was reversible. Desorption of fluoride ions was accomplished by pumping 0.1 N HCl solution. The reusability of adsorbent was studied by subjecting column to repeated cycles of fluoride adsorption and desorption. The suitability of immobilized C. vulgaris adsorbent for fluoride removal from ground water samples of Pavagada taluk, Tumakuru district was studied in the packed column.

Adsorption of Zn(II) from Aqueous Solutions by Thiol-Functionalized MCM-48

2011 ◽  
Vol 413 ◽  
pp. 148-153 ◽  
Author(s):  
Xue Na Hu ◽  
Ya Han ◽  
Jia Yan Li ◽  
Jun Yan Wu ◽  
Jian Rong Chen ◽  
...  
Keyword(s):  
Ethylene Oxide ◽  
Batch Adsorption ◽  
Order Kinetic ◽  
Pluronic P123 ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Poly Ethylene Oxide ◽  
Ft Ir ◽  
Poly Ethylene ◽  
Poly Propylene

Thiol-functionalized MCM-48 (SH-MCM-48) was synthesized by co-condensation method, with co-templates of cetyltrimethylammonium bromide (CTAB) and nonionic poly (ethylene oxide)–poly (propylene oxide)–poly (ethylene oxide) triblock copolymer (Pluronic P123). The resulting material was characterized by XRD and FT-IR spectrum. The potential of SH-MCM-48 for adsorption Zn (II) from aqueous solution was examined. Batch adsorption studies were carried out to investigate the effect of experimental parameters including pH, metal ions concentration and adsorption time. The maximum adsorption capacities of Zn (II) onto SH-MCM-48 were 30.12, 34.01 and 38.02 mg g-1 at the temperature of 303, 313 and 323K, respectively. The adsorption kinetics data were found to follow the pseudo-second-order kinetic model, and adsorption isotherms were fitted well with Langmuir and Freundlich models. Moreover, the adsorption thermodynamic parameters (△G0, △H0 and △S0) were measured, and indicated that the adsorption was an exothermic and spontaneous process.

Sign in / Sign up

Export Citation Format

Share Document