scholarly journals Discharge quality from municipal wastewater treatment plants and the Sludge Biotic Index for activated sludge: integrative assessment

2017 ◽  
Vol 12 (4) ◽  
pp. 857-870
Author(s):  
M. Ostoich ◽  
F. Serena ◽  
C. Zacchello ◽  
L. Falletti ◽  
M. Zambon ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Municipal Wastewater ◽  
Wastewater Treatment Plants ◽  
Ecological Status ◽  
Biotic Index ◽  
Aeration Tank ◽  
Microbiological Analysis ◽  
Limit Values ◽  
Integrative Assessment

Abstract Wastewater treatment plants (WWTPs) are scrutinized by Environmental Authorities particularly regarding the compliance to discharge limit values fixed by national and local regulations. An integrated approach is necessary to achieve the objectives established with Directive 2000/60/EC (WFD) considering the ecological status of the receiving water body and the quality of the discharge. Specifically, documentary, technical, management and analytical controls should be developed. Moreover, integrative information on the behaviour of the activated sludge in the aeration tank can be useful for plant managers as well as for the regulating Authorities. The study presents the experience concerning WWTP regulation considering the analytic assessment of the discharge as well the monitoring of the Sludge Biotic Index (SBI) for activated sludge. Data from monitoring during the period 2008–14 on SBI values and chemical and microbiological data on the discharges of a sample of 35 WWTPs in the province of Venice (north-east Italy, Veneto region) are presented and discussed. Together with chemical and microbiological analysis, the SBI appears to be a highly useful index for the integrative assessment of plant functionality, in particular when monitoring and identifying critical situations that can determine the exceedance of discharge limit values. The SBI method, in an integrated control approach, can be used for small and medium sized WWTPs that only treat domestic wastewaters. In a case by case assessment this may even substitute part of the analytical monitoring carried out in the WWTPs' control process.

PARAMETERS FOR DYNAMIC SIMULATION OF W ASTEW ATER TREATMENT PLANTS WITH HIGH-RATE AND LOW-RATE ACTIVATED SLUDGE TANKS

1994 ◽  
Vol 30 (4) ◽  
pp. 211-214 ◽  
Author(s):  
E. Brands ◽  
M. Liebeskind ◽  
M. Dohmann
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Dynamic Simulation ◽  
Municipal Wastewater ◽  
Wastewater Treatment Plants ◽  
High Rate ◽  
Yield Coefficient ◽  
Municipal Wastewater Treatment ◽  
Municipal Wastewater Treatment Plants ◽  
Low Rate

This study shows a comparison of important parameters for dynamic simulation concerning the highrate and low-rate activated sludge tanks of several municipal wastewater treatment plants. The parameters for the dynamic simulation of the single-stage process are quite well known, but parameters for the high-ratellow-rate activated sludge process are still missi ng, although a considerable number of wastewater treatment plants are designed and operated that way. At present any attempt to simulate their operation is restricted to the second stage due to missing data concerning growth rate, decay rate, yield coefficient and others.

Characterization of wastewater and activated sludge from European municipal wastewater treatment plants using the NUR test

1998 ◽  
Vol 38 (1) ◽  
pp. 303-310 ◽  
Author(s):  
V. Naidoo ◽  
V. Urbain ◽  
C. A. Buckley
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Municipal Wastewater ◽  
Wastewater Treatment Plants ◽  
Municipal Wastewater Treatment ◽  
Batch Tests ◽  
Denitrification Kinetics ◽  
Municipal Wastewater Treatment Plants

Denitrification kinetics and wastewater characterization of eight different plants in Europe are discussed. Denitrification batch tests revealed three distinct rates except in the cases of Plaisir, Rostock and Orense where 4 rates were observed. The latter three plants revealed atypical rapid initial rates which were between 7 and 21 mgN/gVSS.h. All denitrification kinetics under non-limiting carbon conditions revealed fast first rates which ranged between 3.0 and 7.3 mgN/gVSS.h. Acetate was used to simulate denitrification kinetics with readily biodegradable COD present. Two subsequent rates were observed. Rates 2 and 3 ranged between 2 and 3 mgN/gVSS.h, and 1 and 2 mgN/gVSS.h, respectively. The RBCOD fraction varied between 10 and 19%, except for one of the plants where the value determined was 7%.

An investigation into studying of the activated sludge foaming potential by using physicochemical parameters

2002 ◽  
Vol 46 (1-2) ◽  
pp. 525-528 ◽  
Author(s):  
K. Hladikova ◽  
I. Ruzickova ◽  
P. Klucova ◽  
J. Wanner
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Physicochemical Parameters ◽  
Wastewater Treatment Plants ◽  
Physicochemical Characteristics ◽  
Full Scale ◽  
Aeration Tank ◽  
Foam Formation ◽  
Individual Parameter

This paper examines how the physicochemical characteristics of the solids are related to foam formation and describes how the foaming potential of full-scale plants can be assessed. The relations among activated sludge and biological foam hydrophobicity, scum index, aeration tank cover and filamentous population are evaluated. Individual parameter comparison reveals the scumming intensity can be estimated only on the assumption that foams is already established. None of the above mentioned characteristics can be reliably used to predict the foaming episodes at wastewater treatment plants.

scholarly journals Improving and upgrading an existing activated sludge with a compact MBBR – disc filters parallel line for municipal wastewater treatment in touristic alpine areas

2020 ◽  
Vol 15 (2) ◽  
pp. 515-527
Author(s):  
L. Desa ◽  
P. Kängsepp ◽  
L. Quadri ◽  
G. Bellotti ◽  
K. Sørensen ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Municipal Wastewater ◽  
Wastewater Treatment Plants ◽  
Oxygen Demand ◽  
Parallel Line ◽  
Ammonium Nitrogen ◽  
Biofilm Reactor ◽  
Municipal Wastewater Treatment ◽  
Yearly Average

Abstract Many wastewater treatment plants (WWTP) in touristic areas struggle to achieve the effluent requirements due to seasonal variations in population. In alpine areas, the climate also determines a low wastewater temperature, which implies long sludge retention time (SRT) needed for the growth of nitrifying biomass in conventional activated sludge (CAS). Moreover, combined sewers generate high flow and dilution. The present study shows how the treatment efficiency of an existing CAS plant with tertiary treatment can be upgraded by adding a compact line in parallel, consisting of a Moving Bed Biofilm Reactor (MBBR)-coagulation-flocculation-disc filtration. This allows the treatment of influent variations in the MBBR and a constant flow supply to the activated sludge. The performance of the new 2-step process was comparable to that of the improved existing one. Regardless significant variations in flow (10,000–25,000 m3/d) and total suspended solids (TSS) (50–300 mg/L after primary treatment) the effluent quality fulfilled the discharge requirements. Based on yearly average effluent data, TSS were 11 mg/L, chemical oxygen demand (COD) 27 mg/L and total phosphorus (TP) 0.8 mg/L. After the upgrade, ammonium nitrogen (NH4-N) dropped from 4.9 mg/L to 1.3 mg/L and the chemical consumption for phosphorus removal was reduced.

scholarly journals LCA of a Membrane Bioreactor Compared to Activated Sludge System for Municipal Wastewater Treatment

Membranes ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 421
Author(s):  
Dimitra C. Banti ◽  
Michail Tsangas ◽  
Petros Samaras ◽  
Antonis Zorpas
Keyword(s):  
Wastewater Treatment ◽  
Life Cycle ◽  
Activated Sludge ◽  
Membrane Bioreactor ◽  
Municipal Wastewater ◽  
Wastewater Treatment Plants ◽  
Treatment Plant ◽  
Real Data ◽  
Municipal Wastewater Treatment ◽  
Conventional Activated Sludge

Membrane bioreactor (MBR) systems are connected to several advantages compared to the conventional activated sludge (CAS) units. This work aims to the examination of the life cycle environmental impact of an MBR against a CAS unit when treating municipal wastewater with similar influent loading (BOD = 400 mg/L) and giving similar high-quality effluent (BOD < 5 mg/L). The MBR unit contained a denitrification, an aeration and a membrane tank, whereas the CAS unit included an equalization, a denitrification, a nitrification, a sedimentation, a mixing, a flocculation tank and a drum filter. Several impact categories factors were calculated by implementing the Life Cycle Assessment (LCA) methodology, including acidification potential, eutrophication potential, global warming potential (GWP), ozone depletion potential and photochemical ozone creation potential of the plants throughout their life cycle. Real data from two wastewater treatment plants were used. The research focused on two parameters which constitute the main differences between the two treatment plants: The excess sludge removal life cycle contribution—where GWPMBR = 0.50 kg CO2-eq*FU−1 and GWPCAS = 2.67 kg CO2-eq*FU−1 without sludge removal—and the wastewater treatment plant life cycle contribution—where GWPMBR = 0.002 kg CO2-eq*FU−1 and GWPCAS = 0.14 kg CO2-eq*FU−1 without land area contribution. Finally, in all the examined cases the environmental superiority of the MBR process was found.

scholarly journals Initiating Biodegradation of Polyvinylpyrrolidone in an Aqueous Aerobic Environment: Technical Note / Zainicjowanie Biodegradacji Poliwinylopirolidonu W Środowisku Wodno-Tlenowym: Notatki Techniczne

2013 ◽  
Vol 20 (1) ◽  
pp. 199-208 ◽  
Author(s):  
Marketa Julinova ◽  
Jan Kupec ◽  
Roman Slavik ◽  
Maria Vaskova
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Municipal Wastewater ◽  
Waste Treatment ◽  
Wastewater Treatment Plants ◽  
Treatment Plant ◽  
Oxygen Demand ◽  
Technical Note ◽  
Aerobic Biodegradation ◽  
Municipal Wastewater Treatment

Abstract A synthetic polymer, polyvinylpyrrolidone (PVP - E 1201) primarily finds applications in the pharmaceutical and food industries due to its resistance and zero toxicity to organisms. After ingestion, the substance passes through the organism unchanged. Consequently, it enters the systems of municipal wastewater treatment plants (WWTP) without decomposing biologically during the waste treatment process, nor does it attach (through sorption) to particles of activated sludge to any significant extent, therefore, it passes through the system of a WWTP, which may cause the substance to accumulate in the natural environment. For this reason the paper investigates the potential to initiate aerobic biodegradation of PVP in the presence of activated sludge from a municipal wastewater treatment plant. The following agents were selected as the initiators of the biodegradation process - co-substrates: acrylamide, N-acethylphenylalanine and 1-methyl-2-pyrrolidone, a substance with a similar structure to PVP monomer. The biodegradability of PVP in the presence of co-substrates was evaluated on the basis of biological oxygen demand (BOD) as determined via a MicroOxymax O2/CO2/CH4 respirometer. The total substrate concentration in the suspension equaled 400 mg·dm-3, with the ratio between PVP and the cosubstrate being 1:1, while the concentration of the dry activated sludge was 500 mg·dm-3. Even though there was no occurrence of a significant increase in the biodegradation of PVP alone in the presence of a co-substrate, acrylamide appeared to be the most effective type of co-substrate. Nevertheless, a recorded decrease in the slope of biodegradation curves over time may indicate that a process of primary decomposition was underway, which involves the production of metabolites that inhibit activated sludge microorganisms. The resulting products are not identified at this stage of experimentation.

scholarly journals Reliability of removal of selected pollutants in different technological solutions of household wastewater treatment plants

2017 ◽  
Vol 35 (1) ◽  
pp. 141-148 ◽  
Author(s):  
Michał Marzec
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Suspended Solids ◽  
Wastewater Treatment Plants ◽  
Sewage Treatment ◽  
Sewage Treatment Plant ◽  
Treatment Plant ◽  
Total Suspended Solids ◽  
Hybrid Reactor ◽  
Limit Values

AbstractThe reliability of removal of selected contaminants in three technological solutions of the household sewage treatment plants was analysed in this paper. The reliability of the sewage treatment plant with activated sludge, sprinkled biological deposit and hybrid reactor (activated sludge and immersed trickling filter) was analyzed. The analysis was performed using the Weibull method for basic indicators of impurities, BOD5, COD and total suspended solids. The technological reliability of the active sludge treatment plant was 70% for BOD5, 87% for COD and 66% for total suspended solids. In the sewage treatment plant with a biological deposit, the reliability values determined were: 30% (BOD5), 60% (COD) and 67% (total suspended solids). In a treatment plant with a hybrid reactor, 30% of the BOD5and COD limit values were exceeded, while 30% of the total suspended solids were exceeded. The reliability levels are significantly lower than the acceptable levels proposed in the literature, which means that the wastewater discharged from the analysed wastewater treatment plants often exceeds the limit values of indicators specified in currently valid in Poland Regulation of the Minister of Environment for object to 2000 population equivalent.

scholarly journals Activated Sludge Microbial Community and Treatment Performance of Wastewater Treatment Plants in Industrial and Municipal Zones

2020 ◽  
Vol 17 (2) ◽  
pp. 436 ◽  
Author(s):  
Yongkui Yang ◽  
Longfei Wang ◽  
Feng Xiang ◽  
Lin Zhao ◽  
Zhi Qiao
Keyword(s):  
Wastewater Treatment ◽  
Microbial Community ◽  
Activated Sludge ◽  
Municipal Wastewater ◽  
Wastewater Treatment Plants ◽  
Treatment Plant ◽  
Wastewater Sludge ◽  
Community Diversity ◽  
Nitrogen And Phosphorus ◽  
Metabolic Functions

Controlling wastewater pollution from centralized industrial zones is important for reducing overall water pollution. Microbial community structure and diversity can adversely affect wastewater treatment plant (WWTP) performance and stability. Therefore, we studied microbial structure, diversity, and metabolic functions in WWTPs that treat industrial or municipal wastewater. Sludge microbial community diversity and richness were the lowest for the industrial WWTPs, indicating that industrial influents inhibited bacterial growth. The sludge of industrial WWTP had low Nitrospira populations, indicating that influent composition affected nitrification and denitrification. The sludge of industrial WWTPs had high metabolic functions associated with xenobiotic and amino acid metabolism. Furthermore, bacterial richness was positively correlated with conventional pollutants (e.g., carbon, nitrogen, and phosphorus), but negatively correlated with total dissolved solids. This study was expected to provide a more comprehensive understanding of activated sludge microbial communities in full-scale industrial and municipal WWTPs.

Sign in / Sign up

Export Citation Format

Share Document