Influence of nanoparticles on the polymer-conditioned dewatering of wastewater sludges

2013 ◽  
Vol 67 (9) ◽  
pp. 2117-2123
Author(s):  
N. J. Boyle ◽  
G. M. Evans
Keyword(s):  
Activated Sludge ◽  
Titanium Dioxide Nanoparticles ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
Wastewater Sludge ◽  
Small Scale ◽  
Sludge Dewatering ◽  
Solids Content ◽  
The Impact

The effect of using small-scale, high surface area, nanoparticles to supplement polymer-conditioned wastewater sludge dewatering was investigated. Aerobically digested sludge and waste activated sludge sourced from the Hunter Valley, NSW, Australia, were tested with titanium dioxide nanoparticles. The sludge samples were dosed with the nanoparticles in an attempt to adsorb a component of the charged biopolymer surfactants present naturally in sludge. The sludge was conditioned with a cationic polymer. The dewatering characteristics were assessed by measuring the specific resistance to filtration through a modified time-to-filter testing apparatus. The solids content of the dosed samples was determined by a mass balance and compared to the original solids content in the activated sludge. Test results indicated that nanoparticle addition modified the structure of the sludge and provided benefits in terms of the dewatering rate. The samples dosed with nanoparticles exhibited faster water removal, indicating a more permeable filter cake and hence more permeable sludge. A concentration of 2–4% nanoparticles was required to achieve a noticeable benefit. As a comparison, the sludge samples were also tested with a larger particle size, powdered activated carbon (PAC). It was found that the PAC did provide some minor benefits to sludge dewatering but was outperformed by the nanoparticles. The solids content of the final sludge was increased by a maximum of up to 0.6%. The impact of the order sequence of particles and polymer was also investigated. It was found that nanoparticles added before polymer addition provided the best dewatering performance. This outcome was consistent with current theories and previous research through the literature. An economic analysis was undertaken to confirm the viability of the technology for implementation at a full-scale plant. It was found that, currently, this technology is unlikely to be favourable unless the nanoparticles can be sourced for a low cost.

scholarly journals Enhanced adsorption capacity of porous titanium dioxide nanoparticles synthetized in alkaline sol

2020 ◽  
Vol 126 (12) ◽  
Author(s):  
Luigi Scrimieri ◽  
Luciano Velardi ◽  
Antonio Serra ◽  
Daniela Manno ◽  
Francesca Ferrari ◽  
...  
Keyword(s):  
Titanium Dioxide ◽  
Adsorption Capacity ◽  
Industrial Development ◽  
Titanium Dioxide Nanoparticles ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
Porous Titanium ◽  
Electron Microscopies ◽  
Enhanced Adsorption

Abstract In recent years, the exploitation of natural resources and industrial development have led to the production of harmful pollutants. Much of these contaminants end up in water resources, reducing the availability of drinking water. Therefore, it is necessary to find remedies to this situation. Solutions could be the adsorption or the degradation through photocatalysis of these compounds. A good candidate for this task is titanium dioxide (TiO2), due to its non-toxicity, stability and low cost. In this work, we propose a novel synthesis of TiO2 nanoparticles (NPs), with high adsorption capacity, produced at low temperature in alkaline environment. Adsorption tests were conducted using methylene blue and diclofenac as model pollutants. Moreover, the obtained NPs have been characterized through Raman spectroscopy, Scanning and Transmission electron microscopies and with thermogravimetric analysis. The results showed a porous structure with a high surface area, able to efficiently adsorb large amounts of dye from the aqueous solution. These properties make the obtained TiO2 powders suitable for applications devoted to the adsorption and recovery of harmful compounds. Graphic abstract

scholarly journals Synthesis of catalysts with fine platinum particles supported by high-surface-area activated carbons and optimization of their catalytic activities for polymer electrolyte fuel cells

RSC Advances ◽  
2021 ◽  
Vol 11 (33) ◽  
pp. 20601-20611
Author(s):  
Md. Mijanur Rahman ◽  
Kenta Inaba ◽  
Garavdorj Batnyagt ◽  
Masato Saikawa ◽  
Yoshiki Kato ◽  
...  
Keyword(s):  
Fuel Cells ◽  
Polymer Electrolyte ◽  
High Performance ◽  
Activated Carbons ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
Polymer Electrolyte Fuel Cells ◽  
Supported Platinum ◽  
Platinum Particles

Herein, we demonstrated that carbon-supported platinum (Pt/C) is a low-cost and high-performance electrocatalyst for polymer electrolyte fuel cells (PEFCs).

scholarly journals Effects of Annealing Temperature on the Oxygen Evolution Reaction Activity of Copper–Cobalt Oxide Nanosheets

Nanomaterials ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 657
Author(s):  
Geul Han Kim ◽  
Yoo Sei Park ◽  
Juchan Yang ◽  
Myeong Je Jang ◽  
Jaehoon Jeong ◽  
...  
Keyword(s):  
High Activity ◽  
Cobalt Oxide ◽  
Oxygen Evolution ◽  
Oxygen Evolution Reaction ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
Cobalt Hydroxide ◽  
Ni Foam ◽  
Electron Conduction

Developing high performance, highly stable, and low-cost electrodes for the oxygen evolution reaction (OER) is challenging in water electrolysis technology. However, Ir- and Ru-based OER catalysts with high OER efficiency are difficult to commercialize as precious metal-based catalysts. Therefore, the study of OER catalysts, which are replaced by non-precious metals and have high activity and stability, are necessary. In this study, a copper–cobalt oxide nanosheet (CCO) electrode was synthesized by the electrodeposition of copper–cobalt hydroxide (CCOH) on Ni foam followed by annealing. The CCOH was annealed at various temperatures, and the structure changed to that of CCO at temperatures above 250 °C. In addition, it was observed that the nanosheets agglomerated when annealed at 300 °C. The CCO electrode annealed at 250 °C had a high surface area and efficient electron conduction pathways as a result of the direct growth on the Ni foam. Thus, the prepared CCO electrode exhibited enhanced OER activity (1.6 V at 261 mA/cm2) compared to those of CCOH (1.6 V at 144 mA/cm2), Co3O4 (1.6 V at 39 mA/cm2), and commercial IrO2 (1.6 V at 14 mA/cm2) electrodes. The optimized catalyst also showed high activity and stability under high pH conditions, demonstrating its potential as a low cost, highly efficient OER electrode material.

Tailored Mesoporous Silicas: From Confinement Effects to Catalysis

2009 ◽  
Vol 1217 ◽  
Author(s):  
A. C. Buchanan, III ◽  
Michelle K. Kidder
Keyword(s):  
Chemical Reactivity ◽  
High Surface ◽  
High Surface Area ◽  
Mesoporous Silicas ◽  
Surface Immobilization ◽  
Product Selectivity ◽  
Aryl Ether ◽  
Ether Linkage ◽  
Synthetic Methodologies ◽  
The Impact

AbstractOrdered mesoporous silicas continue to find widespread use as supports for diverse applications such as catalysis, separations, and sensors. They provide a versatile platform for these studies because of their high surface area and the ability to control pore size, topology, and surface properties over wide ranges. Furthermore, there is a diverse array of synthetic methodologies for tailoring the pore surface with organic, organometallic, and inorganic functional groups. In this paper, we will discuss two examples of tailored mesoporous silicas and the resultant impact on chemical reactivity. First, we explore the impact of pore confinement on the thermochemical reactivity of phenethyl phenyl ether (PhCH2CH2OPh, PPE), which is a model of the dominant β-aryl ether linkage present in lignin derived from woody biomass. The influence of PPE surface immobilization, grafting density, silica pore diameter, and presence of a second surface-grafted inert “spacer” molecule on the product selectivity has been examined. We will show that the product selectivity can be substantially altered compared with the inherent gas-phase selectivity. Second, we have recently initiated an investigation of mesoporous silica supported, heterobimetallic oxide materials for photocatalytic conversion of carbon dioxide. Through surface organometallic chemistry, isolated M-O-M’ species can be generated on mesoporous silicas that, upon irradiation, form metal to metal charge transfer bands capable of converting CO2 into CO. Initial results from studies of Ti(IV)-O-Sn(II) on SBA-15 will be presented.

Morphology dependent adsorption of methylene blue on trititanate nanoplates and nanotubes prepared by the hydrothermal treatment of TiO2

2016 ◽  
Vol 75 (2) ◽  
pp. 350-357
Author(s):  
Graham Dawson ◽  
Wei Chen ◽  
Luhua Lu ◽  
Kai Dai
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Pore Volume ◽  
Hydrothermal Reaction ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
High Capacity ◽  
Adsorption Properties

The adsorption properties of two nanomorphologies of trititanate, nanotubes (TiNT) and plates (TiNP), prepared by the hydrothermal reaction of concentrated NaOH with different phases of TiO2, were examined. It was found that the capacity for both morphologies towards methylene blue (MB), an ideal pollutant, was extremely high, with the TiNP having a capacity of 130 mg/g, higher than the TiNT, whose capacity was 120 mg/g at 10 mg/L MB concentration. At capacity, the well-dispersed powders deposit on the floor of the reaction vessel. The two morphologies had very different structural and adsorption properties. TiNT with high surface area and pore volume exhibited exothermic monolayer adsorption of MB. TiNP with low surface area and pore volume yielded a higher adsorption capacity through endothermic multilayer adsorption governed by pore diffusion. TiNP exhibited a higher negative surface charge of −23 mV, compared to −12 mV for TiNT. The adsorption process appears to be an electrostatic interaction, with the cationic dye attracted more strongly to the nanoplates, resulting in a higher adsorption capacity and different adsorption modes. We believe this simple, low cost production of high capacity nanostructured adsorbent material has potential uses in wastewater treatment.

Highly active mixed-valent MnOxspheres constructed by nanocrystals as efficient catalysts for long-cycle Li–O2batteries

2016 ◽  
Vol 4 (43) ◽  
pp. 17129-17137 ◽  
Author(s):  
Sanpei Zhang ◽  
Zhaoyin Wen ◽  
Yang Lu ◽  
Xiangwei Wu ◽  
Jianhua Yang
Keyword(s):  
Surface Area ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
Long Cycle ◽  
Highly Active

We demonstrate a low-cost and facile strategy to synthesize mixed-valent MnOxspheres constructed from nanocrystals (~5 nm), containing MnII, MnIII, and MnIVspecies. Such highly active mixed-valent MnOxspheres with high surface area greatly improve the performance of Li–O2batteries.

scholarly journals Green and facile synthesis of cerium doped Ni3Fe electrocatalyst for efficient oxygen evolution reaction

2020 ◽  
Vol 34 (2) ◽  
pp. 353-363
Author(s):  
F. Kanwal ◽  
A. Batool ◽  
R. Akbar ◽  
S. Asim ◽  
M. Saleem
Keyword(s):  
Oxygen Evolution ◽  
Oxygen Evolution Reaction ◽  
Large Scale ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
Three Dimensional ◽  
Alkaline Electrolyte ◽  
Hydrogen Electrode ◽  
Molar Ratios

Electrochemical water splitting is the most promising pathway to produce high-purity hydrogen to alleviate global energy crisis. This reaction demands inexpensive, efficient and robust electrocatalyst for its commercial use. Herein, we demonstrate an effective, facile and scalable method for the synthesis of cerium doped Ni3Fe nanostructures as an electrocatalyst for oxygen evolution reaction (OER) by following simple chemical bath deposition route. The different molar ratios (3, 6 and 12 mM) of cerium in the chemical bath were used to study its effect on the structural and the electrochemical properties of the Ni3Fe nanostructured films. Doping of cerium contents induced variations in the morphology of deposited Ni3Fe nanostructures. The optimized electrocatalyst Ni3Fe/Ce-6 yielded high surface area catalyst nanosheets uniformly deposited on three-dimensional conductive scaffold to ensure increase in the exposure of doped Ni3Fe catalytic sites with high electrical conductivity. As a result, this earth-abundant electrocatalyst affords high OER performance with a small overpotential of 310 mV versus reversible hydrogen electrode (RHE) at 10 mA cm-2 and retains good stability up to ~ 10 h in alkaline electrolyte. This scalable strategy has great potential in future advancement of efficient and low-cost electrocatalysts for their large-scale application in energy conversion systems.                     KEY WORDS: Oxygen evolution, Electrocatalyst, Ni3Fe nanostructures, Cerium, Alkaline electrolyte   Bull. Chem. Soc. Ethiop. 2020, 34(2), 353-363 DOI: https://dx.doi.org/10.4314/bcse.v34i2.12

scholarly journals Darcy–Forchheimer Radiative Flow of Micropoler CNT Nanofluid in Rotating Frame with Convective Heat Generation/Consumption

Processes ◽  
2019 ◽  
Vol 7 (10) ◽  
pp. 666 ◽  
Author(s):  
Ebraheem O. Alzahrani ◽  
Zahir Shah ◽  
Wajdi Alghamdi ◽  
Malik Zaka Ullah
Keyword(s):  
Heat Generation ◽  
High Surface ◽  
High Surface Area ◽  
Numerical Results ◽  
Coupled Equations ◽  
Analysis Technique ◽  
Homotopy Analysis ◽  
Material Energy ◽  
The Impact ◽  
Thermal Radiation Effect

Since 1991, from the beginning of the carbon nanotube era, this has been a focus point for investigation due to its synthetic and simple nature. Unique properties like good stiffness, high surface area, and resilience of carbon nanotubes (CNTs) have been investigated in many engineering applications such as hydrogen storage, composite material, energy storage, electrochemical super-capacitors, transistors, sensors, and field-emitting devices. Keeping in view these applications, we investigate single and multi-walled CNTs nanofluid flow having water as the base fluid between parallel and horizontal rotating plates with microstructure and inertial properties. The thermal radiation effect is considered for variable phenomenon of heat generation/consumption. The principal equations are first symmetrically transformed to a system of nonlinear coupled ordinary differential equations (ODEs), and then, Homotopy Analysis Technique (HAM) and numerical method are employed for solving these coupled equations. The obtained analytical and numerical results are explained graphically and through different tables. The HAM and numerical results show an excellent agreement. The Skin friction and the Nusselt number are numerically calculated and then analyzed with the already published results, and these results are found to be in agreement with one another. The impact of important parameters are shown graphically.

scholarly journals Recent Advances in Oxygen Electrocatalysts Based on Perovskite Oxides

Nanomaterials ◽  
2019 ◽  
Vol 9 (8) ◽  
pp. 1161 ◽  
Author(s):  
Jun Xu ◽  
Chan Chen ◽  
Zhifei Han ◽  
Yuanyuan Yang ◽  
Junsheng Li ◽  
...  
Keyword(s):  
High Performance ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
Precious Metals ◽  
Perovskite Oxides ◽  
Air Battery ◽  
Energy Conversion Devices ◽  
Further Development ◽  
Electrochemical Oxygen

Electrochemical oxygen reduction and oxygen evolution are two key processes that limit the efficiency of important energy conversion devices such as metal–air battery and electrolysis. Perovskite oxides are receiving discernable attention as potential bifunctional oxygen electrocatalysts to replace precious metals because of their low cost, good activity, and versatility. In this review, we provide a brief summary on the fundamentals of perovskite oxygen electrocatalysts and a detailed discussion on emerging high-performance oxygen electrocatalysts based on perovskite, which include perovskite with a controlled composition, perovskite with high surface area, and perovskite composites. Challenges and outlooks in the further development of perovskite oxygen electrocatalysts are also presented.

Sign in / Sign up

Export Citation Format

Share Document