scholarly journals Quarterly technical progress report No. 2, December 20-March 19, 1982. Second quarterly report on the effect of rapid heating rate on coal nitrogen and sulfur release

1982 ◽  
Author(s):  
N. Gat
Materials ◽  
2013 ◽  
Vol 6 (8) ◽  
pp. 3624-3640 ◽  
Author(s):  
Betime Nuhiji ◽  
Darren Attard ◽  
Gordon Thorogood ◽  
Tracey Hanley ◽  
Kevin Magniez ◽  
...  

1993 ◽  
Vol 14 (3) ◽  
pp. 247-259 ◽  
Author(s):  
Roger Avery ◽  
Annabel Basker ◽  
Claudia Corti

AbstractTwo adult Podarcis muralis whose normal movements incorporated the flat top of a wall, frequently paused so that they were looking outwards from an edge ("scan" posture), especially during longer (≥9 s) periods immobile. Investigations of the posture on raised wooden platforms in outdoor enclosures, using two juvenile lizards, showed that (1) lizards spent significantly more time on platforms than would be expected from random movement, and this was not because wood is a favoured substrate for basking; (2) lizards which were immobile on platforms spent significantly more time at edges than would be expected by chance; (3) body orientations at 67.5-112.5° to the edge were the most frequent and these were maintained for significantly longer periods than the remaining orientations; exceptions were from 0800-0900 h when orientation was often parallel to the edge facing the sun and from 1200-1300 h with only a thin strip of shade at 45°, into which the lizards fitted themselves. Lizards basking in the laboratory beneath a tungsten bulb at the edge of a raised platform adopted outward-facing orientations when the platform height was ≥6 mm. When presented with a choice between basking more effectively (i.e. rapid heating rate) or adopting the "scan" posture at an edge with a lower heating rate or with no heating, they opted for the former. Podarcis sicula, P. filfolensis, Lacerta viridis and L. vivipara all showed an excess of outward-facing orientations when the basking bulbs were place near edges of platforms, but Psammodromus hispanicus did not. Only the two Podarcis species, however, spent more time on raised platforms than would be expected by chance when basking was possible at many sites in an arena.


Fuel ◽  
2021 ◽  
Vol 287 ◽  
pp. 119496
Author(s):  
Hanjian Li ◽  
Huanying Chi ◽  
Song Hu ◽  
Yankui Wang ◽  
Gongxiang Song ◽  
...  

CrystEngComm ◽  
2019 ◽  
Vol 21 (3) ◽  
pp. 478-486 ◽  
Author(s):  
Taejin Park ◽  
Changdeuck Bae ◽  
Hyangsook Lee ◽  
Mirine Leem ◽  
Hoijoon Kim ◽  
...  

Non-equilibrium fractal growth of MoS2 was induced by establishing an extremely Mo rich chemical vapor deposition (CVD) environment using a rapid heating rate in a confined reaction space.


2021 ◽  
Vol 8 ◽  
pp. 25
Author(s):  
Olusoji Oluremi Ayodele ◽  
Mary Ajimegoh Awotunde ◽  
Bukola Joseph Babalola ◽  
Peter Apata Olubambi

The densification process and grain analysis of consolidated NiAl-CNT composites at 1000 °C, and at varied heating rates from 50 °C/min to 150 °C/min was investigated. The results revealed the effect of heating rate on the densification behaviour of the samples. The displacement of the composites decreased from 3.39 mm to 2.63 mm with increasing heating rate, while the porosity increased by 69% at rapid heating rate. The grain analysis of the sintered samples through the electron backscattered (EBSD) technique indicates the evolution of bigger grains as the heating rate proceeds higher. Furthermore, the mean grain size of the consolidated composites increased from 3.93 μm, to 8.05 μm due to the concentration of defects. Interestingly, there was no texture or predominance of any color evolution in the sintered materials.


2011 ◽  
Vol 299-300 ◽  
pp. 131-134
Author(s):  
Qi Mei Gao ◽  
Ya Zhen Liu ◽  
Ni Tian

The cold-rolled sheets of the Al-Mg-Si Alloy were annealed for recrystallization in the box furnace and the bath furnace respectively, then the microstructures were observed and the recrystallization textures were investigated with the orientation distribution functions (ODFs). The results show that after recrystallization annealing at slow heating rate the coarse a-Al grains and the strong recrystallization texture composed of Cube+nd25 components and the {011}<323> components were formed in the sheets of the Al-Mg-Si alloy, and after recrystallization annealing at rapid heating rate the fine a-Al grains and the weak or almost random recrystallization textures were formed.


Sign in / Sign up

Export Citation Format

Share Document