scholarly journals Ocena wpływu systemu technologicznego oczyszczania ścieków na charakterystykę osadu czynnego

2017 ◽  
Vol 26 (3) ◽  
pp. 383-393
Author(s):  
Izabela Płonka ◽  
Barbara Pieczykolan
Keyword(s):  
Activated Sludge ◽  
Municipal Wastewater ◽  
Settling Tank ◽  
Operating Conditions ◽  
Volume Index ◽  
Technological Systems ◽  
Tank System ◽  
Bioreactor System ◽  
Secondary Settling ◽  
Biological Methods

Biological methods are used for treatment of municipal wastewater. These processes can be conducted in various kinds of technological systems. In the paper the comparison of characteristic of activated sludge from two types of technological systems is shown. A flow bioreactor with secondary settling tank (system I) and sequential bioreactor (system II) were used. The study showed, that more favorable operating conditions of activated sludge were in the SBR reactor. The activated sludge in SBR reactor had better sedimentary properties, as indicated by values of sludge volume index and flocs’ sizes. This can be connected with the fact that sludge in SRB reactor is not pumped (what occurs in flow systems). Therefore the sludge is not subjected to unfavorable conditions during hydraulic transport (flocs do not undergo the dispersion). Moreover the values of flocs’ sizes, respiratory activity and specific surface area of sludge from II system were higher in comparison with system I.

Control of Activated Sludge Circulation and of Secondary Settling Tank Hydraulics

1988 ◽  
Vol 20 (1) ◽  
pp. 287-290
Author(s):  
R. Huster ◽  
C. H. Möbius
Keyword(s):  
Waste Water ◽  
Activated Sludge ◽  
Load Capacity ◽  
Waste Water Treatment ◽  
Settling Tank ◽  
Effluent Treatment ◽  
Volume Index ◽  
Research Centre ◽  
Capacity Limits ◽  
Secondary Settling

The directives issued by the German Waste Water Association (ABWASSERTECHNISCHE VEREINIGUNG (ATV)) and by the British WATER RESEARCH CENTRE (WRC) in respect of the rating and control of activated sludge circuits and of the loading of secondary settling tanks of biological waste water treatment plants were studied for their applicability to papermill effluents. To this end, several years' testing was carried out on an activated sludge pilot plant and on various industrial plants. These tests revealed that secondary settling tanks of papermill effluent treatment plants may safely be rated in accordance with ATV up to a sludge volume index (SVI) of 300 ml/g and a sludge return rate of 3. If SVI values are low, the WRC process permits excessive surface loadings and is thus only practicable for high SVI levels. If sedimentation properties of the activated sludge are poor, load capacity limits are indicated more correctly by the WRC method. A simplified settling velocity method derived from the WRC process gives reliable information on the load capacity of secondary settling tanks and may readily be used for sludge circulation control.

scholarly journals Intensification of activated sludge sedimentation processes by means of vacuuming

Vestnik MGSU ◽  
2021 ◽  
pp. 370-380
Author(s):  
Artem A. Kulakov ◽  
Alina F. Filatova
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Municipal Wastewater ◽  
Wastewater Treatment Plants ◽  
Settling Tank ◽  
Municipal Wastewater Treatment ◽  
Treated Water ◽  
Mixed Liquor ◽  
Municipal Wastewater Treatment Plants ◽  
Secondary Settling

Introduction. The mixed liquor of nitrogen removal wastewater treatment plants is characterized by a high concentration of nitrates and dissolved oxygen at the inlet to the secondary settling tank. In the sludge layer of secondary sedimentation tanks, conditions of decreased oxygen content and uncontrolled denitrification processes take place. This leads to the floating up and removal of sludge with the effluent and secondary pollution of treated water. The purpose of this article is to study the parameters of activated sludge sedimentation in municipal wastewater treatment plants and their intensification by means of vacuuming. Materials and methods. The studies were carried out under laboratory conditions. Activated sludge vacuuming and sedimentation processes were simulated. Diagrams of the “sludge-water” phase reduction (Kinsh curves) were drawn. Mathematical and graphic processing of the results was carried out. Results. Biological treatment of municipal wastewater (aerotank — secondary settling tank) and methods of its intensification by influencing the activated sludge were considered in this article. Trends of activated sludge (at different concentrations of mixed liquor suspended solids) sedimentation were experimentally obtained for municipal wastewater treatment plants. The process of sludge vacuuming was researched, the process efficiency was determined as a function of the treatment time. Conclusions. Vacuuming allows removing gases from the fluid, which accelerates the process of sludge separation from the treated water and prevents it from floating to the surface. The treated sample is characterized by better sedimentation characteristics, density, coarseness and integrity of flakes. The optimal duration of mixed liquor vacuuming before sedimentation is 0.5 minutes; this accelerates the processes of subsequent sedimentation and reduces the removal of sludge with treated water. The results of laboratory tests can be applied to the design of the mixed liquor vacuuming unit before the secondary sedimentation tanks and its sludge separation.

An equation for the empirical design of anoxic zones used to eliminate rising sludges at nitrifying activated sludge plants

1996 ◽  
Vol 33 (3) ◽  
pp. 185-194 ◽  
Author(s):  
M. Sarioglu ◽  
N. Horan
Keyword(s):  
Activated Sludge ◽  
Empirical Equation ◽  
Nitrate Nitrogen ◽  
Critical Concentration ◽  
Settling Tank ◽  
Limited Information ◽  
Batch Experiments ◽  
Anoxic Zone ◽  
Secondary Settling ◽  
Anoxic Zones

Anoxic zones are designed for the removal of nitrogen in nitrifying activated sludge plants. This can be carried out either to achieve a nitrogen discharge consent or to eliminate the problem of rising sludges. The rising sludge problem is mostly encountered in medium and small size plants in warm conditions and there is limited information as to the appropriate design of anoxic zones to protect against rising sludges in the secondary sedimentation tanks. Therefore a series of batch experiments were undertaken in order to establish the critical concentration of nitrate-nitrogen which causes rising sludge in the secondary settling tank and the effect of environmental factors such as temperature (15°C to 30°C) and residual carbon source (100 to 600 mg/1 COD) were examined. Based on the results of these experiments an empirical equation was presented which can be used to size an anoxic zone to eliminate rising sludges. The application of this equation at full-scale plants is discussed.

Intermittent feeding of wastewater in combination with alternating aeration for complete denitrification and control of filaments

2010 ◽  
Vol 61 (9) ◽  
pp. 2259-2266 ◽  
Author(s):  
Styliani Kantartzi ◽  
Paraschos Melidis ◽  
Alexander Aivasidis
Keyword(s):  
Wastewater Treatment ◽  
Total Nitrogen ◽  
Nitrogen Removal ◽  
Wastewater Treatment Plant ◽  
Municipal Wastewater ◽  
Settling Tank ◽  
Treatment Plant ◽  
Operating Conditions ◽  
Anoxic Conditions ◽  
Total Nitrogen Removal

In the present study, a laboratory scale system, consisting of a primary settling tank, a continuous stirred tank reactor and a clarifier were constructed and operated, using wastewater from the municipal wastewater treatment plant in Xanthi, Greece. The system operated under intermittent aeration in aerobic/anoxic conditions and feeding of the wastewater once in every cycle. The unit was inoculated with sludge, which originated from the recirculation stream of the local wastewater treatment plant. The wastewater was processed with hydraulic retention time (HRT) of 12 h, in which various experimental states were studied regarding the combination of aerobic and anoxic intervals. The wastewater was fed in limited time once in every cycle of aerobic/anoxic conditions at the beginning of the anoxic period. The two states that exhibited highest performance in nitrification and total nitrogen removal were, then, repeated with HRT of 10 h. The results show that, regarding the nitrification stage and the organic load removal, the intermittent system achieved optimum efficiency, with an overall removal of biological oxygen demand (BOD5) and ammonium nitrogen in the range of 93–96% and 91–95% respectively. As far as the total nitrogen removal is concerned, and if the stage of the denitrification is taken into account, the performance of the intermittent system surpassed other methods, as it is shown by the total Kjeldahl nitrogen (TKN) removal efficiency of 85–87%. These operating conditions suppressed the growth of filamentous organisms, a fact reflected at the SVI values, which were lower than 150 ml/g.

A simple empirical model for the clarification-thickening process in wastewater treatment plants

2014 ◽  
Vol 71 (3) ◽  
pp. 366-372
Author(s):  
Y. K. Zhang ◽  
H. C. Wang ◽  
L. Qi ◽  
G. H. Liu ◽  
Z. J. He ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Empirical Model ◽  
Wastewater Treatment Plants ◽  
Volume Index ◽  
Compression Zone ◽  
Efficient Operation ◽  
Secondary Settling ◽  
Sludge Thickening ◽  
Simple Empirical Model

In wastewater treatment plants (WWTPs), activated sludge is thickened in secondary settling tanks and recycled into the biological reactor to maintain enough biomass for wastewater treatment. Accurately estimating the activated sludge concentration in the lower portion of the secondary clarifiers is of great importance for evaluating and controlling the sludge recycled ratio, ensuring smooth and efficient operation of the WWTP. By dividing the overall activated sludge-thickening curve into a hindered zone and a compression zone, an empirical model describing activated sludge thickening in the compression zone was obtained by empirical regression. This empirical model was developed through experiments conducted using sludge from five WWTPs, and validated by the measured data from a sixth WWTP, which fit the model well (R2 = 0.98, p < 0.001). The model requires application of only one parameter, the sludge volume index (SVI), which is readily incorporated into routine analysis. By combining this model with the conservation of mass equation, an empirical model for compression settling was also developed. Finally, the effects of denitrification and addition of a polymer were also analysed because of their effect on sludge thickening, which can be useful for WWTP operation, e.g., improving wastewater treatment or the proper use of the polymer.

scholarly journals Co-treatment of old landfill leachate and municipal wastewater in sequencing batch reactor (SBR): effect of landfill leachate concentration

2016 ◽  
Vol 51 (4) ◽  
pp. 377-387 ◽  
Author(s):  
Kshitij Ranjan ◽  
Shubhrasekhar Chakraborty ◽  
Mohini Verma ◽  
Jawed Iqbal ◽  
R. Naresh Kumar
Keyword(s):  
Removal Efficiency ◽  
Landfill Leachate ◽  
Suspended Solids ◽  
Sequencing Batch Reactor ◽  
Municipal Wastewater ◽  
Batch Reactor ◽  
Operating Conditions ◽  
Volume Index ◽  
Turbidity Removal ◽  
Mixed Liquor

Sequencing batch reactor (SBR) was assessed for direct co-treatment of old landfill leachate and municipal wastewater for chemical oxygen demand (COD), nutrients and turbidity removal. Nitrogen removal was achieved by sequential nitrification and denitrification under post-anoxic conditions. Initially, SBR operating conditions were optimized by varying hydraulic retention time (HRT) at 20% (v/v) landfill leachate concentration, and results showed that 6 d HRT was suitable for co-treatment. SBR performance was assessed in terms of COD, ammonia, nitrate, phosphate, and turbidity removal efficiency. pH, mixed liquor suspended solids, mixed liquor volatile suspended solids (MLVSS), and sludge volume index were monitored to evaluate stability of SBR. MLVSS indicated that biomass was able to grow even at higher concentrations of old landfill leachate. Ammonia and nitrate removal efficiency was more than 93% and 83%, respectively, whereas COD reduction was in the range of 60–70%. Phosphate and turbidity removal efficiency was 80% and 83%, respectively. Microbial growth kinetic parameters indicated that there was no inhibition of biomass growth up to 20% landfill leachate. The results highlighted that SBR can be used as an initial step for direct co-treatment of landfill leachate and municipal wastewater.

Occurrence of Microthrix parvicella in sequencing batch reactors

2014 ◽  
Vol 69 (10) ◽  
pp. 1984-1995 ◽  
Author(s):  
Lana Mallouhi ◽  
Ute Austermann-Haun
Keyword(s):  
Activated Sludge ◽  
Municipal Wastewater ◽  
Batch Reactor ◽  
Oxygen Demand ◽  
Volume Index ◽  
Batch Reactors ◽  
Sequencing Batch Reactors ◽  
Municipal Wastewater Treatment ◽  
Nitrogen And Phosphorus ◽  
Microthrix Parvicella

Sequencing batch reactors (SBRs) are known for high process stability and usually have a good sludge volume index (SVI). Nevertheless, in many SBRs in Germany for municipal wastewater treatment, scum and foam problems can occur, and SVI can be larger than 200 mL/g. The microscopic investigations of the activated sludge from plants with nitrogen and phosphorus removal have shown that Microthrix parvicella is dominant in the activated sludge in most of them. Studies showed that the optimum growth of M. parvicella is performed at a high sludge age (>20 d) and low sludge load in the range of 0.05–0.2 kg of biochemical oxygen demand per kg of total suspended solids per day (kg BOD5/(TSS·d)). The investigations in 13 SBRs with simultaneous aerobic sludge stabilization (most of them are operated with a system called differential internal cycle strategy sequential batch reactor (DIC-SBR)) show that M. parvicella is able to grow in sludge loads less than 0.05 kg BOD5/(kg TSS·d) as well. To optimize the operation of those SBRs, long cycle times (8–12 h) and dosing of iron salts to eliminate long-chain fatty acids are both recommended. This leads to better SVI and keeps M. parvicella at a low frequency.

scholarly journals Effect of polyphenols on activated sludge biomass during the treatment of highly diluted olive mill wastewaters: biomass dynamics and purifying performances

2020 ◽  
Vol 82 (7) ◽  
pp. 1416-1429
Author(s):  
T. E. Elmansour ◽  
L. Mandi ◽  
A. Ahmali ◽  
A. Elghadraoui ◽  
F. Aziz ◽  
...  
Keyword(s):  
Waste Water ◽  
Activated Sludge ◽  
Klebsiella Oxytoca ◽  
Settling Tank ◽  
Oxygen Demand ◽  
Volume Index ◽  
High Concentration ◽  
Olive Mill Waste Water ◽  
Rhizopus Sp ◽  
Olive Mill

Abstract This study aims to investigate the feasibility of treating olive mill waste water (OMWW) by activated sludge pilot (AS) after its high dilution (1%) by urban waste water (UWW) and to study the effect of polyphenol compounds on the biomass during the treatment. Specific oxygen uptake rate (SOUR), mixed liquor volatile suspended solids (MLVSS), chemical oxygen demand (COD) and total polyphenols, were followed up over 100 days. In spite of the polyphenols' high concentration (up to 128 mg·L−1), successful biomass growth of 7.12 g MLVSS.L −1 and activity were achieved. Most of the bacteria (Pseudomonas sp., Klebsiella oxytoca, Citrobacter fereundii, Escherichia coli and Staphylococcus sp.) and fungi (Trichoderma sp., Rhizopus sp., Aspergillus niger, Penicillium sp., Fusarium sp., Alternaria) identified in the aerobic basin during the stabilization stage were known to be resistant to OMWW and showed effective adaptation of the biomass to polyphenols in high concentration. COD and polyphenols were highly eliminated (90%, 92% respectively). The sludge volume index in the pilot settling tank was almost constant at around 120 mL.g −1. This suggests the possibility of managing OMWW by simple injection at a given percentage in already functioning conventional AS treating UWW.

Removal of organic halogens (AOX) from municipal wastewater by powdered activated carbon (PAC)/activated sludge (AS) treatment

1997 ◽  
Vol 35 (10) ◽  
pp. 147-153 ◽  
Author(s):  
C. Bornhardt ◽  
J. E. Drewes ◽  
M. Jekel
Keyword(s):  
Activated Carbon ◽  
Activated Sludge ◽  
Municipal Wastewater ◽  
Activated Carbons ◽  
Treatment Plant ◽  
Volume Index ◽  
Enhancement Effect ◽  
Simultaneous Treatment ◽  
Volatile Solids ◽  
Organic Halogens

The effectiveness of different treatments with powdered activated carbons (PAC) to reduce the AOX-levels in municipal wastewater was investigated in a bench-scale activated sludge (AS) treatment plant. The PAC was added either directly to the aerated basin (simultaneous PAC-treatment), or to a partial stream of clarified effluent, which was treated with PAC in an agitated tank and recirculated to the aerated basin (subsequent PAC-treatment with recirculation). The standard advanced biological treatment reduced the AOX-content by 24%. In the pilot-plant, three types of powdered activated carbons were tested for a simultaneous treatment. The treatment with 100 mg/l PICA PCO Super produced an additional reduction of AOX by 20%, whereas a dosage of 50 mg/l NORIT W-20 showed no enhancement effect, and W-35 led to an additional AOX-removal of about 9%. Also, an improved removal of DOC, NH4-N and PO4-P was observed. In all cases, the PAC addition caused a significantly improved settling of the AS, reducing the sludge-volume-index, and increasing the content of volatile solids of the PAC-sludge. In general, no evidence of a synergistic effect of the PAC addition to activated sludge, nor bioregeneration of the activated carbon, could be observed. This suggests, that the observed effects probably are caused only by simple adsorption.

Nitrogen removal from wastewater in a pilot plant operated in the recirculation anoxic-oxic activated sludge mode

1996 ◽  
Vol 33 (12) ◽  
pp. 255-258 ◽  
Author(s):  
Olga Burica ◽  
Marjeta Strazar ◽  
Ivan Mahne
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Wastewater Treatment Plant ◽  
Pilot Plant ◽  
Municipal Wastewater ◽  
Treatment Plant ◽  
Volume Ratio ◽  
Mineral Nitrogen ◽  
Operating Conditions ◽  
Effluent Quality

The recirculation activated sludge process with preanoxic treatment was applied for biological reduction of the nitrogen content in municipal wastewater at pilot plant level. The pilot plant of total volume 3 300 1 with an initial anoxic to aerobic volume ratio of 40 : 60 was fed with wastewater from the first heavily loaded aerobic stage of a local wastewater treatment plant. Experiments were run over the summer and winter periods, the influent wastewater temperature being approx 24°C and approx 10°C, respectively. Special attention was paid to the hydraulic retention time, the total as well as mineral nitrogen loading, the aerobic to anaerobic volume ratio, and to the energy demand for denitrification of oxidised mineral nitrogen forms. Under optimal operating conditions the effluent quality that could be achieved was about 10 mg/l of total nitrogen (74% removal) and less than 2 mg N/l mineral nitrogen (87% removal), while simultaneously 205 mg BOD5/l in the influent was reduced to less than 7mg O2/l in the effluent. It was found feasible from the pilot plant experiments to upgrade an existing two stage aerobic-anaerobic wastewater treatment plant to reduce nitrogen from the liquid fraction of municipal wastewater so as to meet effluent quality standards without much additional volume and without amending the energy source for bioconversion of oxidised mineral nitrogen to gaseous forms.

Sign in / Sign up

Export Citation Format

Share Document