scholarly journals Effect of Rolling Temperature on Room Temperature Formability and Texture Formation of Mg-3 mass％Al-1 mass％Sn Alloy Sheet

2021 ◽  
Vol 85 (3) ◽  
pp. 120-127
Author(s):  
Hitoshi Fukuoka ◽  
Xinsheng Huang ◽  
Kazutaka Suzuki ◽  
Yuhki Tsukada ◽  
Toshiyuki Koyama ◽  
...  
Keyword(s):  
Room Temperature ◽  
Alloy Sheet ◽  
Rolling Temperature ◽  
Texture Formation

Texture of AZ31 Magnesium Alloy Sheet Heavily Rolled by High Speed Warm Rolling

2007 ◽  
Vol 539-543 ◽  
pp. 3359-3364 ◽  
Author(s):  
Tetsuo Sakai ◽  
Hiroshi Utsunomiya ◽  
H. Koh ◽  
S. Minamiguchi
Keyword(s):  
Magnesium Alloy ◽  
High Speed ◽  
Room Temperature ◽  
Alloy Sheet ◽  
Rolling Temperature ◽  
Az31 Magnesium Alloy ◽  
Basal Texture ◽  
Double Peak ◽  
Magnesium Alloy Sheet ◽  
Az31 Magnesium Alloy Sheet

Magnesium alloy sheets had to be rolled at elevated temperature to avoid cracking. The poor workability of magnesium alloy is ascribed to its hcp crystallography and insufficient activation of independent slip systems. Present authors have succeeded in 1-pass heavy rolling of AZ31 magnesium alloy sheet below 473K by raising rolling speed above 1000m/min. Heavy reduction larger than 60% can be applied by 1-pass high speed rolling even at room temperature. The improvement of workability at lower rolling temperature is due to temperature rise by plastic working. The texture of heavily rolled AZ31 magnesium alloy sheet is investigated in the present study. The texture of sheets rolled 60% at room temperature was <0001>//ND basal texture. At the rolling temperature above 373K, the peak of (0001) pole tilted ±10-15 deg toward RD direction around TD axisto form a double peak texture. The texture varied through thickness. At the surface, the (0001) peak tilted ±10-15 deg toward TD direction around RD axis to form a TD-split double peak texture. The direction of (0001) peak splitting rotated 90 deg from the surface to the center of thickness. Heavily rolled magnesium alloy sheets have non-basal texture. The sheets having non-basal texture are expected to show better ductility than sheets with basal texture.

Improving Room-Temperature Stretch Formability of Mg-4.9Al-0.16Mn (mass%) Alloy Sheet via Optimizing Rolling Temperature

JOM ◽  
2021 ◽  
Author(s):  
Taiki Nakata ◽  
Chao Xu ◽  
Takumi Fujii ◽  
Yu Yoshida ◽  
Katsuhito Yoshida ◽  
...  
Keyword(s):  
Room Temperature ◽  
Alloy Sheet ◽  
Rolling Temperature ◽  
Stretch Formability

Study on the Microstructure and Texture of Warm Rolled ZK60 Magnesium Alloy Sheet

2012 ◽  
Vol 557-559 ◽  
pp. 1344-1348
Author(s):  
Hong Mei Chen ◽  
Hua Shun Yu ◽  
Guang Hui Min ◽  
Yun Xue Jin
Keyword(s):  
Shear Bands ◽  
Rolling Direction ◽  
Rolling Process ◽  
Warm Rolling ◽  
Alloy Sheet ◽  
Rolling Temperature ◽  
Rolling Reduction ◽  
Basal Pole ◽  
Zk60 Alloy ◽  
Twin Roll

The microstructure and macrotexture of ZK60 alloy sheet were investigated through OM and XRD, which were produced by twin roll casting and sequential warm rolling. Microstructure of twin roll cast ZK60 alloy changed from dendrite structure to fibrous structure with elongated grains and high density shear bands along the rolling direction after warm rolling process at different rolling parameters. The density of shear bands increased with the decreasing of the rolling temperature, or the increasing of per pass rolling reduction. Dynamic recrystallization could be found during the warm rolling process at and above 350oC, and many fine grains could be found in the shear band area. The warm rolled ZK60 alloy sheet exhibited strong (0001) basal pole texture. The formation of the shear bands tends to cause the basal pole tilt slightly to the transverse direction after warm rolling. The intensity of (0001) pole figure increased with the decreasing of rolling temperature, or the increasing of per pass rolling reduction.

Anomalous effect of grain size on the room-temperature bendability of Mg–Gd alloy sheet

2021 ◽  
pp. 142397
Author(s):  
Chao He ◽  
Ming Yuan ◽  
Bin Jiang ◽  
Lintao Liu ◽  
Qinghang Wang ◽  
...  
Keyword(s):  
Grain Size ◽  
Room Temperature ◽  
Alloy Sheet ◽  
Anomalous Effect

Improvement of Mechanical Properties and Corrosion Resistance by Deformation Induced Precipitation in Al-Zn-Mg-Cu Alloy

2017 ◽  
Vol 898 ◽  
pp. 179-190 ◽  
Author(s):  
Jin Rong Zuo ◽  
Long Gang Hou ◽  
Jin Tao Shi ◽  
Hua Cui ◽  
Lin Zhong Zhuang ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Thermomechanical Treatment ◽  
High Strength ◽  
Alloy Sheet ◽  
Rolling Temperature ◽  
Al Alloy ◽  
Deformation Degree ◽  
Dynamic Aging ◽  
Final Rolling Temperature ◽  
Final Rolling

A final thermomechanical treatment (FTMT) including peak aging and subsequent dynamic aging was proposed to prepare 7055 Al alloy sheets. The optimization was based on nine well-planned orthogonal experiments. Three main processing conditions in the thermomechanical treatment for obtaining the optimum synthetic properties of 7055 (i.e. preheating temperature, final rolling temperature and deformation degree) were investigated. It was shown that the final rolling temperature is the most important factor among the three parameters, and the optimum properties (yield strength: 651 MPa, ultimate tensile strength: 660 MPa) of 7055 Al alloy sheet can be gained with preheating at 140oC and 40% deformation at 170oC. With dynamic aging, grain boundary precipitates became discontinuous without much coarsening of matrix precipitates, while they were continuously distributed after T6 aging. The present optimal FTMT process can improve the intergranular / exfoliation corrosion resistance without sacrificing the strength compared to T6 tempering. The present FTMT process as a good alternative can produce high-strength Al alloy sheets with high strength and good corrosion resistance efficiently and economically.

scholarly journals Effect of Cold Rolling and Heat Treatment on the Mechanical Properties of GH4169 Alloy Sheet at Room Temperature

Metals ◽  
2015 ◽  
Vol 6 (1) ◽  
pp. 1 ◽  
Author(s):  
Shi-Hong Zhang ◽  
Neng-Yong Ye ◽  
Ming Cheng ◽  
Hong-Wu Song ◽  
Hong-Wei Zhou ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Cold Rolling ◽  
Room Temperature ◽  
Alloy Sheet ◽  
Gh4169 Alloy

Influence of Pressure Amplitude on Formability in Pulsating Hydro-Bugling of AZ31B Magnesium Alloy Sheet

2011 ◽  
Vol 128-129 ◽  
pp. 397-402
Author(s):  
Lian Fa Yang ◽  
Liang Yi ◽  
Chen Guo
Keyword(s):  
Magnesium Alloy ◽  
Wall Thickness ◽  
Room Temperature ◽  
Alloy Sheet ◽  
Pressure Amplitude ◽  
Excellent Performance ◽  
Az31b Magnesium Alloy ◽  
Stress Components ◽  
Uniform Expansion ◽  
Az31b Magnesium Alloy Sheet

The formability of the magnesium alloy sheets is poor at room temperature even though the magnesium alloy sheets are attractive because of their excellent characteristics. Application of pulsating hydroforming is a new and effective method to improve the formability. The effects of the pressure amplitude on the maximum bulging height and minimum wall thickness of the formed parts of AZ31B magnesium alloy sheets are examined using finite element simulations. It is shown that the distribution of maximum bugling height and minimum wall thickness is similar for different pressure amplitude A, and a uniform expansion in bulging region is obtained, the cause of the uniform expansion obtained may be caused by the variation of stress components. The AZ31B sheet has an excellent performance in formability when the pressure amplitude and pulsating frequency are properly selected.

scholarly journals Influence of Powder Structure on Texture Formation in Superconducting Bi(Pb)–Sr–Ca–Cu–O Ceramics in Magnetic Field

1999 ◽  
Vol 32 (1-4) ◽  
pp. 65-70
Author(s):  
V. M. Gundyrev ◽  
K. M. Demchuk ◽  
A. N. Martemianov ◽  
G. G. Taluts
Keyword(s):  
Magnetic Field ◽  
Room Temperature ◽  
Strong Influence ◽  
Texture Formation ◽  
Grain Alignment

Starting powder of Bi(Pb)–Sr–Ca–Cu–O superconductor consisting mainly of 2223- phase was separated into fractions by precipitation in toluene. The high-oriented stacking of grains of the monocrystalline fractions with different dispersity has been obtained in magnetic field of 2 T at room temperature. The size of the powder grains in the range of 2–20 μm has no strong influence on the texture. The best result of grain alignment has been obtained for the powder grains of 10 μm in size.

Evolution of Microstructure during Hot Deformation of the PM Molybdenum Alloy TZM

2007 ◽  
Vol 539-543 ◽  
pp. 2725-2730 ◽  
Author(s):  
T. Mrotzek ◽  
Andreas Hoffmann ◽  
U. Martin ◽  
H. Oettel
Keyword(s):  
Yield Strength ◽  
Hot Deformation ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
High Strength ◽  
Tensile Tests ◽  
Primary Recrystallization ◽  
Molybdenum Alloy ◽  
Texture Formation ◽  
Evolution Of Microstructure

The molybdenum alloy TZM (Mo-0.5wt%Ti-0.08wt%Zr) is a commonly used structural material for high temperature applications. For these purposes a high strength at elevated temperatures and also a sufficient ductility at room temperature are being aimed. Preceding investigations revealed the existence of subgrains in hot deformed TZM. It was observed that with proceeding primary recrystallization and therefore with disappearance of subgrains the yield strength drops almost to a level of pure molybdenum. It is being assumed that the existence of a dislocation substructure has a pronounced effect on the yield strength of TZM. The aim of the present study was to evaluate the subgrain and texture formation and also to estimate the dislocation arrangement within subgrains during hot deformation. Hence, TZM rods were rolled to different degrees of deformation at a temperature above 0.5 Tm. The microstructure of the initial material was fully recrystallized. Texture formation, misorientation distributions and subgrain sizes were analyzed by electron backscattering diffraction (EBSD). Mechanical properties were characterized by tensile tests at room temperature and up to 1200°C. It was revealed, that with increasing degree of deformation a distinct substructure forms and therefore yield strength rises. Consequently, the misorientation between adjacent subgrains increases, their size decreases and a <110> fibre texture develops. To estimate the influence of texture on strength of TZM the Taylor factors are calculated from EBSD data.

Sign in / Sign up

Export Citation Format

Share Document