scholarly journals Effects of Sintering Temperature on Corrosion Resistance of Titanium Alloys Prepared by Spark Plasma Sintering

1999 ◽  
Vol 63 (5) ◽  
pp. 569-572
Author(s):  
Jun Onagawa ◽  
Yoshiyuki Sato
Keyword(s):  
Corrosion Resistance ◽  
Titanium Alloys ◽  
Spark Plasma Sintering ◽  
Sintering Temperature ◽  
Plasma Sintering ◽  
Spark Plasma

Microstructure and properties of pure aluminum prepared by spark plasma sintering

2019 ◽  
Vol 116 (3) ◽  
pp. 312 ◽  
Author(s):  
Wen Zeng ◽  
Weicai Qin ◽  
Cheng Gu ◽  
Hao Sun ◽  
Yilong Ma ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Spark Plasma Sintering ◽  
Sintering Temperature ◽  
Pure Aluminum ◽  
Triple Junctions ◽  
Corrosion Morphology ◽  
X Ray ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Microstructure Density

Pure Aluminum (Al) powder was densified by spark plasma sintering (SPS). The effects of sintering temperature (450–600 °C) on microstructure, density, hardness and corrosion resistance of the sintered samples were investigated. The methods used in the present study were scanning electron microscopy equipped with energy dispersive X-ray spectroscopy, X-ray diffraction, electrochemical workstation and hardness measurements. The results show that the sintering temperature obviously affects the hardness, relative density, microstructures and corrosion resistance of the sintered Al samples. However, there are different trends with increasing sintering temperature. The maximum hardness (37.7 HV) was obtained at the sample sintered at 550 °C. The polarization curves and corrosion morphology analyses indicated that the sample sintered at 450 °C has the best corrosion resistance (Icorr = 0.344 µA · cm−2). Besides, it was found that the sample sintered at 600 °C was burnt and had many holes along grain boundaries and at triple junctions.

scholarly journals Investigation of Microstructure and Corrosion Resistance of Ti-Al-V Titanium Alloys Obtained by Spark Plasma Sintering

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 945
Author(s):  
Aleksey Nokhrin ◽  
Pavel Andreev ◽  
Maksim Boldin ◽  
Vladimir Chuvil’deev ◽  
Mikhail Chegurov ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Titanium Alloys ◽  
Spark Plasma Sintering ◽  
High Resistance ◽  
Electrochemical Corrosion ◽  
High Hardness ◽  
Acidic Aqueous Solution ◽  
Plasma Sintering ◽  
Salt Corrosion ◽  
Spark Plasma

The research results of the microstructure and corrosion resistance of Ti and Ti-Al-V Russian industrial titanium alloys obtained by spark plasma sintering (SPS) are described. Investigations of the microstructure, phase composition, hardness, tensile strength, electrochemical corrosion resistance and hot salt corrosion of Ti-Al-V titanium alloy specimens were carried out. It was shown that the alloy specimens have a uniform highly dense microstructure and high hardness values. The studied alloys also have high resistance to electrochemical corrosion during tests in acidic aqueous solution causing the intergranular corrosion as well as high resistance to the hot salt corrosion. The assumption that the high hardness of the alloys as well as the differences in the corrosion resistance of the central and lateral parts of the specimens are due to the diffusion of carbon from the graphite mold into the specimen surface was suggested.

Effect of spark plasma sintering temperature on structure and phase composition of Ti-Al-Nb-based alloys

2017 ◽  
Vol 59 (11-12) ◽  
pp. 1033-1036 ◽  
Author(s):  
Sherzod Kurbanbekov ◽  
Mazhyn Skakov ◽  
Viktor Baklanov ◽  
Batyrzhan Karakozov
Keyword(s):  
Phase Composition ◽  
Spark Plasma Sintering ◽  
Sintering Temperature ◽  
Plasma Sintering ◽  
Spark Plasma

Effect of Spark Plasma Sintering on the Microstructure Evolution and Properties of M3:2 High-Speed Steel

2014 ◽  
Vol 788 ◽  
pp. 329-333
Author(s):  
Rui Zhou ◽  
Xiao Gang Diao ◽  
Jun Chen ◽  
Xiao Nan Du ◽  
Guo Ding Yuan ◽  
...  
Keyword(s):  
Powder Metallurgy ◽  
Spark Plasma Sintering ◽  
High Speed ◽  
Bending Strength ◽  
Sintering Temperature ◽  
High Speed Steel ◽  
Continuous Heating ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
The Impact

Effects of sintering temperatures on the microstructure and mechanical performance of SPS M3:2 high speed steel prepared by spark plasma sintering was studied. High speed steel sintering curve of continuous heating from ambient temperature to 1200°C was estimated to analyze the sintering processes and sintering temperature range. The sintering temperature within this range was divided into groups to investigate hardness, relative density and microstructure of M3:2 high-speed steel. Strip and quadrate carbides were observed inside the equiaxed grains. SPS sintering temperature at 900°C can lead to nearly full densification with grain size smaller than 20μm. The hardness and bending strength are higher than that of the conventionally powder metallurgy fabricated ones sintered at 1270°C. However, fracture toughness of the high speed steel is lower than that of the conventional powder metallurgy steels. This can be attributed to the shape and distribution of M6C carbides which reduce the impact toughness of high speed steels.

Production of Dispersion-Strengthened Cu-TiB2 Alloys by Ball-Milling and Spark-Plasma Sintering

2007 ◽  
Vol 534-536 ◽  
pp. 1489-1492 ◽  
Author(s):  
Dae Hwan Kwon ◽  
Jong Won Kum ◽  
Thuy Dang Nguyen ◽  
Dina V. Dudina ◽  
Pyuck Pa Choi ◽  
...  
Keyword(s):  
Electrical Conductivity ◽  
Ball Milling ◽  
Spark Plasma Sintering ◽  
Ball Mill ◽  
Milling Time ◽  
Rotation Speed ◽  
Sintering Temperature ◽  
Milled Powder ◽  
Plasma Sintering ◽  
Spark Plasma

Dispersion-strengthened copper with TiB2 was produced by ball-milling and spark plasma sintering (SPS).Ball-milling was performed at a rotation speed of 300rpm for 30 and 60min in Ar atmosphere by using a planetary ball mill (AGO-2). Spark-plasma sintering was carried out at 650°C for 5min under vacuum after mechanical alloying. The hardness of the specimens sintered using powder ball milled for 60min at 300rpm increased from 16.0 to 61.8 HRB than that of specimen using powder mixed with a turbular mixer, while the electrical conductivity varied from 93.40% to 83.34%IACS. In the case of milled powder, hardness increased as milling time increased, while the electrical conductivity decreased. On the other hand, hardness decreased with increasing sintering temperature, but the electrical conductiviey increased slightly

scholarly journals Mechanical Milling-Assisted Spark Plasma Sintering of Fine-Grained W-Ni-Mn Alloy

Materials ◽  
2018 ◽  
Vol 11 (8) ◽  
pp. 1323 ◽  
Author(s):  
Yanlin Pan ◽  
Daoping Xiang ◽  
Ning Wang ◽  
Hui Li ◽  
Zhishuai Fan
Keyword(s):  
Spark Plasma Sintering ◽  
Mechanical Milling ◽  
Bending Strength ◽  
Sintering Temperature ◽  
Interface Fracture ◽  
Composite Powders ◽  
Fine Grained ◽  
Plasma Sintering ◽  
Binding Phase ◽  
Spark Plasma

Fine-grained W-6Ni-4Mn alloys were fabricated by spark plasma sintering (SPS) using mechanical milling W, Ni and Mn composite powders. The relative density of W-6Ni-4Mn alloy increases from 71.56% to 99.60% when it is sintered at a low temperature range of 1000–1200 °C for 3 min. The spark plasma sintering process of the alloy can be divided into three stages, which clarify the densification process of powder compacts. As the sintering temperature increases, the average W grain size increases but remains at less than 7 µm and the distribution of the binding phase is uniform. Transmission electron microscopy (TEM) observation reveals that the W-6Ni-4Mn alloy consists of the tungsten phase and the γ-(Ni, Mn, W) binding phase. As the sintering temperature increases, the Rockwell hardness and bending strength of alloys initially increases and then decreases. The optimum comprehensive hardness and bending strength of the alloy are obtained at 1150 °C. The main fracture mode of the alloys is W/W interface fracture.

scholarly journals Structure and Deformation Behavior of Ti-SiC Composites Made by Mechanical Alloying and Spark Plasma Sintering

Materials ◽  
2019 ◽  
Vol 12 (8) ◽  
pp. 1276 ◽  
Author(s):  
Dariusz Garbiec ◽  
Volf Leshchynsky ◽  
Alberto Colella ◽  
Paolo Matteazzi ◽  
Piotr Siwak
Keyword(s):  
Mechanical Alloying ◽  
Spark Plasma Sintering ◽  
Indentation Size Effect ◽  
Sintering Temperature ◽  
High Energy ◽  
Indentation Size ◽  
X Ray ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Energy Ball

Combining high energy ball milling and spark plasma sintering is one of the most promising technologies in materials science. The mechanical alloying process enables the production of nanostructured composite powders that can be successfully spark plasma sintered in a very short time, while preserving the nanostructure and enhancing the mechanical properties of the composite. Composites with MAX phases are among the most promising materials. In this study, Ti/SiC composite powder was produced by high energy ball milling and then consolidated by spark plasma sintering. During both processes, Ti3SiC2, TiC and Ti5Si3 phases were formed. Scanning electron microscopy, energy-dispersive X-ray spectroscopy and X-ray diffraction study showed that the phase composition of the spark plasma sintered composites consists mainly of Ti3SiC2 and a mixture of TiC and Ti5Si3 phases which have a different indentation size effect. The influence of the sintering temperature on the Ti-SiC composite structure and properties is defined. The effect of the Ti3SiC2 MAX phase grain growth was found at a sintering temperature of 1400–1450 °C. The indentation size effect at the nanoscale for Ti3SiC2, TiC+Ti5Si3 and SiC-Ti phases is analyzed on the basis of the strain gradient plasticity theory and the equation constants were defined.

Sign in / Sign up

Export Citation Format

Share Document