scholarly journals An Approach to Predict the Depth of the Decarburized Ferrite Layer of Spring Steel Based on Measured Temperature History of Material during Cooling

2014 ◽  
Vol 54 (7) ◽  
pp. 1682-1689 ◽  
Author(s):  
Sangwoo Choi ◽  
Youngseog Lee
2014 ◽  
Vol 611-612 ◽  
pp. 1553-1559
Author(s):  
Lars Kjäldman ◽  
Jouni Syrjänen

As part of the EU/SME project SafeFlame (www.safeflameproject.eu ) the heating of a Cu pipe by a H2/O2 flame has been modeled and the results are compared to experiments. CFD (Computational Fluid Dynamics) modeling has been utilized to study the flow and combustion in the flame and the heat transfer from the flame to the pipe. The simulation results are compared with the measured temperature history of the pipe at different locations and with the visual flame. The influence of distance between the burner and the pipe and of using two opposite H2/O2 flames on the heating rate of the pipe has been investigated. Reasonable agreement between modeling and experiments has been obtained. The reasons for differences between modeling and experimental results are discussed.


2019 ◽  
Vol 2019 ◽  
pp. 1-13 ◽  
Author(s):  
Yaoying Huang ◽  
Tong Xie ◽  
Chunguang Li ◽  
Xiaohui Yin

The measured temperature of a concrete pouring block depends strongly on the position of the buried thermometer. Only when the temperature measured by the thermometer accurately reflects the actual temperature of the concrete pouring block do reasonable temperature-control measures become possible. However, little research has been done on how to determine the proper position of thermometers buried in a concrete pouring block embedded with cooling pipes. To address this situation, we develop herein a method to determine the position of thermometers buried in a concrete pouring block. First, we assume that the design temperature-control process line characterizes the average-temperature history of the concrete pouring block. Under this assumption, we calculate the average-temperature history of the concrete pouring block by using the water-pipe-cooling FEM, following which the temperature history of an arbitrary point in the concrete pouring block is obtained by interpolating the shape function. Based on the average-temperature history of the concrete pouring block and the temperature history of the arbitrary point, we build a mathematical model to optimize the buried position of the thermometer and use the optimization algorithm to determine this position. By using this method, we establish finite-element models of concrete prisms with four typical water-pipe spacing cases for concrete-dam engineering and obtain the geometric position of the thermometers by using the optimization algorithm. By burying thermometers at these positions, the measured temperature should better characterize the average-temperature history of the concrete pouring block, which can provide useful information for regulating the temperature of concrete pouring blocks.


2000 ◽  
Vol 657 ◽  
Author(s):  
Deborah J. Vickers-Kirby ◽  
Randall L. Kubena ◽  
Frederic P. Stratton ◽  
Richard J. Joyce ◽  
David T. Chang ◽  
...  

ABSTRACTDuring the past several years, we have developed high displacement sensitivity tunneling accelerometers using surface micromachining and metal electroplating techniques. These devices consist of a Au tunneling tip fabricated below a 1-2 μm thick metal cantilever beam of electroplated Ni or Au. A thin film of e-beam evaporated Au on the underside of the cantilever serves as the tunneling counter electrode. In operation, a 100mV bias is applied across the tunneling gap. A larger turn-on voltage is also applied between the cantilever and a control electrode, located on the substrate, to deflect the cantilever and maintain a constant tunneling current of 1 or 10 nA. Typical deflections of the end of 100 μm-long and 250 μm-long cantilevers are 0.5μm during operation. We have observed that the turn-on voltage decreases over time for most devices with a larger drop observed for the Au cantilevers. In all cases, the initial decay of the turn-on voltage was almost completely recoverable after the device was turned off for 24 hrs. This decay was not found to be strongly dependent on the magnitude of the tunneling current, but could be significantly reduced by pre-stressing the cantilever before operation. Finally, a vacuum anneal at 100°C influences the measured temperature dependence of the turn-on voltage. The observed effects appear to be consistent with fatigue and creep phenomena in the cantilevers. These effects are reversible at room temperature and are dependent on the stress and temperature history of the devices. A comparison is made between metal plated and all-Si structures.


2005 ◽  
Vol 2005 (3) ◽  
pp. 393-400 ◽  
Author(s):  
Zhi Qian ◽  
Chu-Li Fu ◽  
Xiang-Tuan Xiong

We consider an inverse heat conduction problem (IHCP) in a quarter plane. We want to know the distribution of surface temperature in a body from a measured temperature history at a fixed location inside the body. This is a severely ill-posed problem in the sense that the solution (if exists) does not depend continuously on the data. Eldén (1995) has used a difference method for solving this problem, but he did not obtain the convergence atx=0. In this paper, we gave a logarithmic stability of the approximation solution atx=0under a stronger a priori assumption‖u(0,t)‖p≤Ewithp>1/2. A numerical example shows that the computational effect of this method is satisfactory.


2006 ◽  
Vol 129 (8) ◽  
pp. 966-976 ◽  
Author(s):  
S. W. Paik ◽  
K. D. Kihm ◽  
S. P. Lee ◽  
D. M. Pratt

The spatially and temporally resolved evaporation phenomena of a slowly evaporating water droplet are investigated using a microfabricated gold heater array consisting of 32 linear heater elements (100 μm wide and 15 mm long, each). Each of the gold microheater elements works both as a temperature sensor and as a heater. The experiment is performed under a constant voltage mode to examine the spatially resolved temperature history of the droplet contact surface for a period starting at initial contact with the heater and lasting to the point of complete dryout. The raw data obtained from the linear array have been tomographically deconvolved so that the radial temperature profile can be determined assuming a circular droplet contact surface.


2012 ◽  
Vol 6 (3) ◽  
pp. 675-686 ◽  
Author(s):  
V. Zagorodnov ◽  
O. Nagornov ◽  
T. A. Scambos ◽  
A. Muto ◽  
E. Mosley-Thompson ◽  
...  

Abstract. Two ice core boreholes of 143.18 m and 447.73 m (bedrock) were drilled during the 2009–2010 austral summer on the Bruce Plateau at a location named LARISSA Site Beta (66°02' S, 64°04' W, 1975.5 m a.s.l.). Both boreholes were logged with thermistors shortly after drilling. The shallow borehole was instrumented for 4 months with a series of resistance thermometers with satellite uplink. Surface temperature proxy data derived from an inversion of the borehole temperature profiles are compared to available multi-decadal records from weather stations and ice cores located along a latitudinal transect of the Antarctic Peninsula to West Antarctica. The LARISSA Site Beta profiles show temperatures decreasing from the surface downward through the upper third of the ice, and warming thereafter to the bed. The average temperature for the most recent year is −14.78°C (measured at 15 m depth, abbreviated T15). A minimum temperature of −15.8°C is measured at 173 m depth, and basal temperature is estimated to be −10.2°C. Current mean annual temperature and the gradient in the lower part of the measured temperature profile have a best fit with an accumulation rate of 1.9×103 kg m−2 a−1 and basal heat flux (q) of 88 mW m−2, if steady-state conditions are assumed. However, the mid-level temperature variations show that recent temperature has varied significantly. Reconstructed surface temperatures (Ts=T15) over the last 200 yr are derived by an inversion technique (Tikhonov and Samarskii, 1990). From this, we find that cold temperatures (minimum Ts=−16.2°C) prevailed from ~1920 to ~1940, followed by a gradual rise of temperature to −14.2°C around 1995, then cooling over the following decade and warming in the last few years. The coldest period was preceded by a relatively warm 19th century at T15≥−15°C. To facilitate regional comparisons of the surface temperature history, we use our T15 data and nearby weather station records to refine estimates of lapse rates (altitudinal, adjusted for latitude: Γa(l)). Good temporal and spatial consistency of Γa(l) over the last 35 yr are observed, implying that the climate trends observed here are regional and consistent over a broad altitude range.


Author(s):  
Neil S. Bailey ◽  
Yung C. Shin

A predictive laser hardening model for industrial parts with complex geometric features has been developed and used for optimization of hardening processes. A transient three-dimensional thermal model is combined with a three-dimensional kinetic model for steel phase transformation and solved in order to predict the temperature history and solid phase history of the workpiece while considering latent heat of phase transformation. Further, back-tempering is also added to the model to determine the phase transformation during multitrack laser hardening. The integrated model is designed to accurately predict temperature, phase distributions and hardness inside complex geometric domains. The laser hardening parameters for two industrial workpieces are optimized for two different industrial laser systems using this model. Experimental results confirm the validity of predicted results.


2018 ◽  
Vol 24 (2) ◽  
pp. 321-332 ◽  
Author(s):  
Joseph Bartolai ◽  
Timothy W. Simpson ◽  
Renxuan Xie

Purpose The weakest point in additively manufactured polymer parts produced by material extrusion additive manufacturing (MEAM) is the interface between adjacent layers and deposition toolpaths or “roads”. This study aims to predict the mechanical strength of parts by utilizing a novel analytical approach. Strength predictions are made using the temperature history of these interfaces, polymer rheological data, and polymer weld theory. Design/methodology/approach The approach is validated using experimental data for two common 3D-printed polymers: polycarbonate (PC) and acrylonitrile butadiene styrene (ABS). Interface temperature history data are collected in situ using infrared imaging. Rheological data of the polycarbonate and acrylonitrile butadiene styrene used to fabricate the fused filament fabrication parts in this study have been determined experimentally. Findings The strength of the interfaces has been predicted, to within 10% of experimental strength, using polymer weld theory from the literature adapted to the specific properties of the polycarbonate and acrylonitrile butadiene styrene feedstock used in this study. Originality/value This paper introduces a novel approach for predicting the strength of parts produced by MEAM based on the strength of interfaces using polymer weld theory, polymer rheology, temperature history of the interface and the forces applied to the interface. Unlike methods that require experimental strength data as a prediction input, the proposed approach is material and build orientation agnostic once fundamental parameters related to material composition have been determined.


Sign in / Sign up

Export Citation Format

Share Document