Predicting strength of additively manufactured thermoplastic polymer parts produced using material extrusion

2018 ◽  
Vol 24 (2) ◽  
pp. 321-332 ◽  
Author(s):  
Joseph Bartolai ◽  
Timothy W. Simpson ◽  
Renxuan Xie
Keyword(s):  
Infrared Imaging ◽  
Acrylonitrile Butadiene Styrene ◽  
Temperature History ◽  
Interface Temperature ◽  
Fused Filament Fabrication ◽  
Content Type ◽  
Material Extrusion ◽  
Rheological Data ◽  
History Of ◽  
Butadiene Styrene

Purpose The weakest point in additively manufactured polymer parts produced by material extrusion additive manufacturing (MEAM) is the interface between adjacent layers and deposition toolpaths or “roads”. This study aims to predict the mechanical strength of parts by utilizing a novel analytical approach. Strength predictions are made using the temperature history of these interfaces, polymer rheological data, and polymer weld theory. Design/methodology/approach The approach is validated using experimental data for two common 3D-printed polymers: polycarbonate (PC) and acrylonitrile butadiene styrene (ABS). Interface temperature history data are collected in situ using infrared imaging. Rheological data of the polycarbonate and acrylonitrile butadiene styrene used to fabricate the fused filament fabrication parts in this study have been determined experimentally. Findings The strength of the interfaces has been predicted, to within 10% of experimental strength, using polymer weld theory from the literature adapted to the specific properties of the polycarbonate and acrylonitrile butadiene styrene feedstock used in this study. Originality/value This paper introduces a novel approach for predicting the strength of parts produced by MEAM based on the strength of interfaces using polymer weld theory, polymer rheology, temperature history of the interface and the forces applied to the interface. Unlike methods that require experimental strength data as a prediction input, the proposed approach is material and build orientation agnostic once fundamental parameters related to material composition have been determined.

Correlation of tribo-mechanical properties of internal geometry structures of fused filament fabrication 3D-printed acrylonitrile butadiene styrene

2020 ◽  
Vol 72 (10) ◽  
pp. 1259-1265
Author(s):  
Mohamad Nordin Mohamad Norani ◽  
Mohd Fadzli Bin Abdollah ◽  
Muhammad Ilman Hakimi Chua Abdullah ◽  
Hilmi Amiruddin ◽  
Faiz Redza Ramli ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Wear Rate ◽  
Peer Review ◽  
Tribological Properties ◽  
Acrylonitrile Butadiene Styrene ◽  
Fused Filament Fabrication ◽  
Content Type ◽  
Internal Geometry ◽  
3D Printed ◽  
Butadiene Styrene

Purpose This study aims is to investigate the correlation between tribological and mechanical properties of the fused filament fabrication 3D-printed acrylonitrile butadiene styrene (ABS) pin with different internal geometries. Design/methodology/approach The tribological properties were determined by a dry sliding test with constant test parameters, while the hardness and modulus of elasticity were determined by microhardness and compression tests. Findings Although the internal geometry of the pin sample slightly affects the coefficient of friction (COF) and the wear rate of the 3D-printed ABS, it was important to design a lightweight tribo-component by reducing the material used to save energy without compromising the strength of the component. The COF and wear rate values are relatively dependent on the elastic modulus. A 3D-printed ABS pin with an internal triangular flip structure was found to have the shortest run-in period and the lowest COF with high wear resistance. Abrasive wear and delamination are the predominant wear mechanisms involved. Research limitations/implications The findings are the subject of future research under various sliding conditions by investigating the synergistic effect of sliding speeds and applied loads to validate the results of this study. Originality/value The internal structure affects the mechanical properties and release stress concentration at the contact point, resulting in hypothetically low friction and wear. This approach may also reduce the weight of the parts without scarifying or at least preserving their preceding tribological performance. Therefore, based on our knowledge, limited studies have been conducted for the application of 3D printing in tribology, and most studies focused on improving their mechanical properties rather than correlating them with tribological properties that would benefit longer product lifespans. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-04-2020-0143/

scholarly journals Essential work of fracture assessment of acrylonitrile butadiene styrene (ABS) processed via fused filament fabrication additive manufacturing

2021 ◽  
Author(s):  
Pawan Verma ◽  
Jabir Ubaid ◽  
Andreas Schiffer ◽  
Atul Jain ◽  
Emilio Martínez-Pañeda ◽  
...  
Keyword(s):  
Acrylonitrile Butadiene Styrene ◽  
Essential Work ◽  
Fused Filament Fabrication ◽  
Essential Work Of Fracture ◽  
Fracture Properties ◽  
Raster Angle ◽  
3D Printed ◽  
Printing Direction ◽  
Work Of Fracture ◽  
Butadiene Styrene

AbstractExperiments and finite element (FE) calculations were performed to study the raster angle–dependent fracture behaviour of acrylonitrile butadiene styrene (ABS) thermoplastic processed via fused filament fabrication (FFF) additive manufacturing (AM). The fracture properties of 3D-printed ABS were characterized based on the concept of essential work of fracture (EWF), utilizing double-edge-notched tension (DENT) specimens considering rectilinear infill patterns with different raster angles (0°, 90° and + 45/− 45°). The measurements showed that the resistance to fracture initiation of 3D-printed ABS specimens is substantially higher for the printing direction perpendicular to the crack plane (0° raster angle) as compared to that of the samples wherein the printing direction is parallel to the crack (90° raster angle), reporting EWF values of 7.24 kJ m−2 and 3.61 kJ m−2, respectively. A relatively high EWF value was also reported for the specimens with + 45/− 45° raster angle (7.40 kJ m−2). Strain field analysis performed via digital image correlation showed that connected plastic zones existed in the ligaments of the DENT specimens prior to the onset of fracture, and this was corroborated by SEM fractography which showed that fracture proceeded by a ductile mechanism involving void growth and coalescence followed by drawing and ductile tearing of fibrils. It was further shown that the raster angle–dependent strength and fracture properties of 3D-printed ABS can be predicted with an acceptable accuracy by a relatively simple FE model considering the anisotropic elasticity and failure properties of FFF specimens. The findings of this study offer guidelines for fracture-resistant design of AM-enabled thermoplastics. Graphical abstract

Effects of infill patterns on the strength and stiffness of 3D printed topologically optimized geometries

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Nadim S. Hmeidat ◽  
Bailey Brown ◽  
Xiu Jia ◽  
Natasha Vermaak ◽  
Brett Compton
Keyword(s):  
Material Properties ◽  
Failure Modes ◽  
Mechanical Anisotropy ◽  
Failure Behavior ◽  
Fused Filament Fabrication ◽  
Content Type ◽  
Orthotropic Composite ◽  
Material Extrusion ◽  
Specific Material ◽  
Strength And Stiffness

Purpose Mechanical anisotropy associated with material extrusion additive manufacturing (AM) complicates the design of complex structures. This study aims to focus on investigating the effects of design choices offered by material extrusion AM – namely, the choice of infill pattern – on the structural performance and optimality of a given optimized topology. Elucidation of these effects provides evidence that using design tools that incorporate anisotropic behavior is necessary for designing truly optimal structures for manufacturing via AM. Design/methodology/approach A benchmark topology optimization (TO) problem was solved for compliance minimization of a thick beam in three-point bending and the resulting geometry was printed using fused filament fabrication. The optimized geometry was printed using a variety of infill patterns and the strength, stiffness and failure behavior were analyzed and compared. The bending tests were accompanied by corresponding elastic finite element analyzes (FEA) in ABAQUS. The FEA used the material properties obtained during tensile and shear testing to define orthotropic composite plies and simulate individual printed layers in the physical specimens. Findings Experiments showed that stiffness varied by as much as 22% and failure load varied by as much as 426% between structures printed with different infill patterns. The observed failure modes were also highly dependent on infill patterns with failure propagating along with printed interfaces for all infill patterns that were consistent between layers. Elastic FEA using orthotropic composite plies was found to accurately predict the stiffness of printed structures, but a simple maximum stress failure criterion was not sufficient to predict strength. Despite this, FE stress contours proved beneficial in identifying the locations of failure in printed structures. Originality/value This study quantifies the effects of infill patterns in printed structures using a classic TO geometry. The results presented to establish a benchmark that can be used to guide the development of emerging manufacturing-oriented TO protocols that incorporate directionally-dependent, process-specific material properties.

Printing with mechanically interlocked extrudates using a custom bi-extruder for fused deposition modelling

2018 ◽  
Vol 24 (6) ◽  
pp. 921-934 ◽  
Author(s):  
Mohammad Abu Hasan Khondoker ◽  
Asad Asad ◽  
Dan Sameoto
Keyword(s):  
Cross Sections ◽  
Acrylonitrile Butadiene Styrene ◽  
Easy Access ◽  
Fused Deposition Modelling ◽  
Content Type ◽  
Immiscible Polymers ◽  
Fused Deposition ◽  
Functionally Gradient ◽  
Different Sources ◽  
Butadiene Styrene

Purpose This paper aims to target to print functionally gradient materials (FGM) devices made of immiscible polymers in multi-material fused deposition modelling (FDM) systems. The design is intended to improve adhesion of dissimilar thermoplastics without the need for chemical compatibilization so that filaments from many different sources can be used effectively. Therefore, there is a need to invent an alternative solution for printing multiple immiscible polymers in an FDM system with the desired adhesion. Design/methodology/approach In this study, the authors have developed a bi-extruder for FDM systems which can print two thermoplastics through a single nozzle with a static intermixer to enhance bonding between input materials. The system can also change the composition of extrudates continuously. Findings The uniqueness of this extruder is in its easy access to the internal channel so that a static intermixer can be inserted, enabling deposition of mechanically interlocked extrudates composed of two immiscible polymers. Without this intermixer, the bi-extruder extrudes with simple side-by-side co-extrusion having no mechanical interlocking. The bi-extruder was characterized by printing objects using pairs of materials including polylactic acid, acrylonitrile butadiene styrene and high impact polystyrene. Microscope images of the cross-sections of the extrudates confirm the ability of this bi-extruder to control the composition as desired. It was also found that the mechanically interlocked extrudates composed of two immiscible polymers substantially reduces adhesion failures within and between filaments. Originality/value In this study, the first-ever FDM extruder with a mechanical blending feature next to the nozzle has been designed and used to successfully print FGM objects with improved mechanical properties.

scholarly journals Fatigue Performance of ABS Specimens Obtained by Fused Filament Fabrication

Materials ◽  
2018 ◽  
Vol 11 (12) ◽  
pp. 2521 ◽  
Author(s):  
Miquel Domingo-Espin ◽  
J. Antonio Travieso-Rodriguez ◽  
Ramon Jerez-Mesa ◽  
Jordi Lluma-Fuentes
Keyword(s):  
Acrylonitrile Butadiene Styrene ◽  
Experimental Phase ◽  
Fused Filament Fabrication ◽  
Layer Height ◽  
Bending Stresses ◽  
Best Parameter ◽  
End Use ◽  
Design And Manufacture ◽  
Printing Speed ◽  
Butadiene Styrene

In this paper, the fatigue response of fused filament fabrication (FFF) Acrylonitrile butadiene styrene (ABS) parts is studied. Different building parameters (layer height, nozzle diameter, infill density, and printing speed) were chosen to study their influence on the lifespan of cylindrical specimens according to a design of experiments (DOE) using the Taguchi methodology. The same DOE was applied on two different specimen sets using two different infill patterns—rectilinear and honeycomb. The results show that the infill density is the most important parameter for both of the studied patterns. The specimens manufactured with the honeycomb pattern show longer lifespans. The best parameter set associated to that infill was chosen for a second experimental phase, in which the specimens were tested under different maximum bending stresses so as to construct the Wöhler curve associated with this 3D printing configuration. The results of this study are useful to design and manufacture ABS end-use parts that are expected to work under oscillating periodic loads.

Mechanical properties of composite parts manufactured in FDM technology

2018 ◽  
Vol 24 (8) ◽  
pp. 1281-1287 ◽  
Author(s):  
Filip Górski ◽  
Wiesław Kuczko ◽  
Radosław Wichniarek ◽  
Adam Hamrol
Keyword(s):  
Acrylonitrile Butadiene Styrene ◽  
Strength Properties ◽  
Bending Tests ◽  
Static Tests ◽  
Content Type ◽  
Thermoplastic Matrix ◽  
New Type ◽  
Simultaneous Decrease ◽  
Practical Implications ◽  
Butadiene Styrene

Purpose This paper aims to study strength properties and accuracy of a new type of composites, in which matrix is manufactured additively, whereas infill is a polyurethane resin. The process of manufacturing these composites is invented and patented by authors. Design/methodology/approach The authors developed a method of manufacturing composites, which was then used to build samples for tensile and bending tests (according to ISO 572 and ISO 178 standards), as well as measurements of accuracy. Findings It was found that the method of composite manufacturing designed by the authors allows obtaining both stronger and cheaper parts in comparison with the traditional acrylonitrile butadiene styrene FDM parts. Research limitations/implications The research was limited to static tests only, and no dynamic tests were performed on the manufactured samples. The accuracy analysis is only a basic one. Practical implications Developed method allows to shorten the FDM process with simultaneous decrease of costs (in professional processes) and increase of strength of obtained products. Originality/value Application of composite materials presented in the paper will significantly expand possibilities of using FDM method to manufacture functional, strong parts able to carry higher loads. Application of different combinations of thermoplastic matrix materials with different resin infills will allow to control properties of obtained composites. The solution is currently subject of a patent.

scholarly journals Does vaporized hydrogen peroxide sterilization affect the geometrical properties of anatomic models and guides 3D printed from computed tomography images?

2021 ◽  
Vol 7 (1) ◽  
Author(s):  
Mauricio Toro ◽  
Aura Cardona ◽  
Daniel Restrepo ◽  
Laura Buitrago
Keyword(s):  
Computed Tomography ◽  
Hydrogen Peroxide ◽  
Dimensional Stability ◽  
Acrylonitrile Butadiene Styrene ◽  
Dimensional Error ◽  
Material Extrusion ◽  
Anatomic Models ◽  
3D Printed ◽  
Mean Differences ◽  
Butadiene Styrene

Abstract Background Material extrusion is used to 3D print anatomic models and guides. Sterilization is required if a 3D printed part touches the patient during an intervention. Vaporized Hydrogen Peroxide (VHP) is one method of sterilization. There are four factors to consider when sterilizing an anatomic model or guide: sterility, biocompatibility, mechanical properties, and geometric fidelity. This project focuses on geometric fidelity for material extrusion of one polymer acrylonitrile butadiene styrene (ABS) using VHP. Methods De-identified computed tomography (CT) image data from 16 patients was segmented using Mimics Innovation Suite (Materialise NV, Leuven, Belgium). Eight patients had maxillary and mandibular defects depicted with the anatomic models, and eight had mandibular defects for the anatomic guides. Anatomic models and guides designed from the surfaces of CT scan reconstruction and segementation were 3D printed in medical-grade acrylonitrile butadiene styrene (ABS) material extrusion. The 16 parts underwent low-temperature sterilization with VHP. The dimensional error was estimated after sterilization by comparing scanned images of the 3D printed parts. Results The average of the estimated mean differences between the printed pieces before and after sterilization were − 0,011 ± 0,252 mm (95%CI − 0,011; − 0,010) for the models and 0,003 ± 0,057 mm (95%CI 0,002; 0,003) for the guides. Regarding the dimensional error of the sterilized parts compared to the original design, the estimated mean differences were − 0,082 ± 0,626 mm (95%CI − 0,083; − 0,081) for the models and 0,126 ± 0,205 mm (95%CI 0,126, 0,127) for the guides. Conclusion This project tested and verified dimensional stability, one of the four prerequisites for introducing vaporized hydrogen peroxide into 3D printing of anatomic models and guides; the 3D printed parts maintained dimensional stability after sterilization.

scholarly journals Sustainable Additive Manufacturing: Mechanical Response of Acrylonitrile-Butadiene-Styrene over Multiple Recycling Processes

2020 ◽  
Vol 12 (9) ◽  
pp. 3568 ◽  
Author(s):  
Nectarios Vidakis ◽  
Markos Petousis ◽  
Athena Maniadi ◽  
Emmanuel Koudoumas ◽  
Achilles Vairis ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Mechanical Behavior ◽  
Mechanical Response ◽  
Positive Impact ◽  
Research Work ◽  
Acrylonitrile Butadiene Styrene ◽  
Experimental Simulation ◽  
Recycling Rate ◽  
Fused Filament Fabrication ◽  
Butadiene Styrene

Sustainability in additive manufacturing refers mainly to the recycling rate of polymers and composites used in fused filament fabrication (FFF), which nowadays are rapidly increasing in volume and value. Recycling of such materials is mostly a thermomechanical process that modifies their overall mechanical behavior. The present research work focuses on the acrylonitrile-butadiene-styrene (ABS) polymer, which is the second most popular material used in FFF-3D printing. In order to investigate the effect of the recycling courses on the mechanical response of the ABS polymer, an experimental simulation of the recycling process that isolates the thermomechanical treatment from other parameters (i.e., contamination, ageing, etc.) has been performed. To quantify the effect of repeated recycling processes on the mechanic response of the ABS polymer, a wide variety of mechanical tests were conducted on FFF-printed specimens. Regarding this, standard tensile, compression, flexion, impact and micro-hardness tests were performed per recycle repetition. The findings prove that the mechanical response of the recycled ABS polymer is generally improved over the recycling repetitions for a certain number of repetitions. An optimum overall mechanical behavior is found between the third and the fifth repetition, indicating a significant positive impact of the ABS polymer recycling, besides the environmental one.

Effect of extrusion temperature on fused filament fabrication parts orthotropic behaviour

2019 ◽  
Vol 26 (4) ◽  
pp. 639-647
Author(s):  
Michele Angelo Attolico ◽  
Caterina Casavola ◽  
Alberto Cazzato ◽  
Vincenzo Moramarco ◽  
Gilda Renna
Keyword(s):  
Mechanical Properties ◽  
Morphological Characteristics ◽  
Single Layer ◽  
Acrylonitrile Butadiene Styrene ◽  
Surface Characteristics ◽  
Tensile Tests ◽  
Extrusion Temperature ◽  
Fused Filament Fabrication ◽  
Bonding Quality ◽  
Content Type

Purpose The purpose of this paper is to verify the effects of extrusion temperature on orthotropic behaviour of the mechanical properties of parts obtained by fused filament fabrication (FFF) under quasi-static tensile loads. Design/methodology/approach Tensile tests were performed on single layer specimens fabricated in polylactic acid (PLA) and acrylonitrile butadiene styrene (ABS) to evaluate the mechanical properties at different extrusion temperatures and raster orientations (0°, 45° and 90°). Furthermore, a detailed study of morphological characteristics of the single layer samples cross-section and of the bonding quality among adjacent deposited filaments was performed by scanning electron microscopy to correlate the morphology of materials with mechanical behaviour. Findings The results show that the orthotropic behaviour of FFF-printed parts tends to reduce, while the mechanical properties improved with increase in extrusion temperature. Furthermore, the increase in extrusion temperature led to an improvement in inter-raster bonding quality and in the compactness and homogeneity of the parts. Originality/value The relation between the extrusion temperature, orthotropic behaviour and morphological surface characteristics of the single layer specimen obtained by FFF has not been previously reported.

scholarly journals Comparative study of the flexural properties of ABS, PLA and a PLA–wood composite manufactured through fused filament fabrication

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
J.A. Travieso-Rodriguez ◽  
R. Jerez-Mesa ◽  
Jordi Llumà ◽  
Giovanni Gomez-Gras ◽  
Oriol Casadesus
Keyword(s):  
Additive Manufacturing ◽  
Acrylonitrile Butadiene Styrene ◽  
Nozzle Diameter ◽  
Bending Test ◽  
Mechanical Resistance ◽  
Fused Filament Fabrication ◽  
Content Type ◽  
Layer Height ◽  
Maximum Deformation ◽  
Materials Used

Purpose The aim of this paper is to analyze the mechanical properties of acrylonitrile-butadiene-styrene (ABS) parts manufactured through fused filament fabrication and compare these results to analogous ones obtained on polylactic acid (PLA) and PLA–wood specimens to contribute for a wider understanding of the different materials used for additive manufacturing. Design/methodology/approach With that aim, an experimental based on an L27 Taguchi array was used to combine the specific parameters taken into account in the study, namely, layer height, nozzle diameter, infill density, orientation and printing velocity. All samples were subjected to a four-point bending test performed according to the ASTM D6272 standard. Findings Young’s modulus, elastic limit, maximum stress and maximum deformation of every sample were computed and subjected to an analysis of variance. Results prove that layer height and nozzle diameter are the most significant factors that affect the mechanical resistance in pieces generated through additive manufacturing and subjected to bending loads, regardless of the material. Practical implications The best results were obtained by combining a layer height of 0.1 mm and a nozzle diameter of 0.6 mm. The comparison of materials evidenced that PLA and its composite version reinforced with wood particles present more rigidity than ABS, whereas the latter can experience further deflection before break. Originality/value This study is of interest for manufacturers that want to decide which is the best material to be applied for their application, as it derives in a practical technical recommendation of the best parameters that should be selected to treat the material during the fused filament fabrication process.

Sign in / Sign up

Export Citation Format

Share Document