The influence of trajectory design parameters on miss distance and survivability of anti-ship missiles

Author(s):  
Bui Quoc Dung ◽  
Cao Huu Tinh ◽  
Nguyen Cong Thuc ◽  
Do Manh Dan
2015 ◽  
Vol 119 (1213) ◽  
pp. 389-405 ◽  
Author(s):  
M. Pavic ◽  
B. Pavkovic ◽  
S. Mandic ◽  
S. Zivkovic ◽  
D. Cuk

AbstractThe impact point dispersion of mortar missiles can be drastically reduced with a control ring of lateral pulse jets located around the centre of gravity and a homing head to measure or to derive estimates of appropriate missile-target states, e.g. the line-of-sight rates. A simulation model including a missile as a six-degree-of-freedom vehicle, a jet pulse flight control system, and a relative missile-to-target motion was used for the comparison of four guidance laws i.e. proportional navigation guidance, augmented proportional navigation, augmented proportional navigation with rendezvous, and adaptive sliding-mode guidance. This paper focuses on the efficiency of pulse jet control on miss distance, and thus makes the assumption that sensor measurements and the guidance states required to apply each of the guidance laws are perfectly known. Proportional navigation and the adaptive sliding mode guidance exhibit a large miss distance due to limited control authority. Augmented proportional navigation is slightly better than augmented proportional navigation with rendezvous for the same design parameters and they both give small miss distances with limited control authority, but they both require a free gyro. A proper selection of the design parameters — the number of pulse jets and the magnitude of the individual pulse jet thrust for a particular dispersion of flight parameters and the instant of the guidance start — is required to achieve optimum dispersion reduction. The minimum intensity of the individual pulse jet impulse required for the ‘pin point’ accuracy (the circular error probable smaller than 1m) of the mortar missile was determined for all presented guidance laws considering dispersion from the nominal trajectory.


2014 ◽  
Vol 8 (5) ◽  
pp. 204 ◽  
Author(s):  
Peng Yong-Tao ◽  
Wang Yue-Ping ◽  
Wei Wen-Ling ◽  
Wang Xiao-Ting

Unpowered drop test is very important for reusable launch vehicle (RLV) autolanding technology development. One of the challenges is to design an autolanding trajectory with enough robustness against uncertainties of drop conditions, aerodynamic characteristic and disturbances from control system and environment. In this paper, a   solution including trajectory generation and control design is proposed for a drop test RLV demonstrator. Firstly, the drop test and vertical flight trajectory are introduced. Also, parts of the drop flight, segments of landing trajecory and trajectory design parameters in groups are shown. Secondly, an online trajectory generation method including self-adapted capture segment plan and landing trajectory optimization following UAV auto-landing experience are illustrated in detail by designing groups of parameters. Then, simple but practical gain schedule control laws are presented. Finally, mathematic simulation and analysis based on both RSS and Monte Carlo methods indicate that the solution proposed has shown an acceptable robustness and can provide enough capability for the demonstrator to land saftly.


Author(s):  
Mikhail Yu. GUNCHENKO

The paper provides results of estimated accuracy comparisons for applied satellite constellations (ASC) in Molniya-type high elliptical orbits based on a previously presented criterion for analysis of accuracy parameters of ASC that observe targets on the Earth surface and/or in the layer above the surface, which is not dependent on specific features of the onboard equipment, but rather on the structure and dynamics of the ASC. The paper provides an algorithm for numerical simulations of ASC. The paper discusses accuracy parameters for ASC in high elliptical orbits in various orbital configurations, as well as a combined option involving spacecraft in geostationary orbit. It defines key trajectory design parameters driving the ASC accuracy. The results can be used for selecting the initial ASC configuration in high elliptical orbits during preliminary design phase. Key words: observation satellite systems, high elliptical orbits, accuracy criterion, satellite constellation analysis.


Author(s):  
Mikhail Yu. GUNCHENKO

The paper provides results of estimated accuracy comparisons for applied satellite constellations (ASC) in Molniya-type high elliptical orbits based on a previously presented criterion for analysis of accuracy parameters of ASC that observe targets on the Earth surface and/or in the layer above the surface, which is not dependent on specific features of the onboard equipment, but rather on the structure and dynamics of the ASC. The paper provides an algorithm for numerical simulations of ASC. The paper discusses accuracy parameters for ASC in high elliptical orbits in various orbital configurations, as well as a combined option involving spacecraft in geostationary orbit. It defines key trajectory design parameters driving the ASC accuracy. The results can be used for selecting the initial ASC configuration in high elliptical orbits during preliminary design phase. Key words: observation satellite systems, high elliptical orbits, accuracy criterion, satellite constellation analysis.


Author(s):  
C J R Sheppard

The confocal microscope is now widely used in both biomedical and industrial applications for imaging, in three dimensions, objects with appreciable depth. There are now a range of different microscopes on the market, which have adopted a variety of different designs. The aim of this paper is to explore the effects on imaging performance of design parameters including the method of scanning, the type of detector, and the size and shape of the confocal aperture.It is becoming apparent that there is no such thing as an ideal confocal microscope: all systems have limitations and the best compromise depends on what the microscope is used for and how it is used. The most important compromise at present is between image quality and speed of scanning, which is particularly apparent when imaging with very weak signals. If great speed is not of importance, then the fundamental limitation for fluorescence imaging is the detection of sufficient numbers of photons before the fluorochrome bleaches.


Currently, the professional construction community information field is largely filled with the topic of creating a comfortable living environment. However, architectural and engineering design that corresponds to the concept of sustainable development is currently hindered due to the lack of a formed conceptual framework that reveals the meaning of the term "comfort", as well as a criteria list that determines the indoor environment quality in the Russian Federation regulatory and technical framework. The article offers some components of a comfortable living environment, within which the parameters of designing the internal environment of premises are highlighted. A comparative analysis of the national standards of the Russian Federation regulating the design of the internal space of residential and public buildings, with international "green" standards for a number of parameters was carried out. It is concluded that it is necessary to update the Russian regulatory and technical base taking into account the international experience of "green" standards.


2016 ◽  
Vol 22 (2(99)) ◽  
pp. 48-51
Author(s):  
D.S. Kalynychenko ◽  
◽  
Ye.Yu. Baranov ◽  
M.V. Poluian ◽  
◽  
...  

Sign in / Sign up

Export Citation Format

Share Document