Erosion Test of Permanent Magnet Pole in the Sea Environment

2018 ◽  
Author(s):  
Yunbo Zheng ◽  
Xiwen Yu ◽  
Dong Wang ◽  
Junquan Chen ◽  
Siwei Cheng
Keyword(s):  
Permanent Magnet ◽  
Erosion Test

NEW PERMANENT MAGNET DEVICES

1984 ◽  
Vol 45 (C1) ◽  
pp. C1-285-C1-291 ◽  
Author(s):  
R. Pauthenet
Keyword(s):  
Permanent Magnet

A novel analytical calculation of magnetic field in the slotted air gap of spoke-type permanent-magnet machines using conformal mapping

2020 ◽  
pp. 1-15
Author(s):  
Jianqi Li ◽  
Yu Zhou ◽  
Jianying Li
Keyword(s):  
Magnetic Field ◽  
Conformal Mapping ◽  
Permanent Magnet ◽  
Flux Density ◽  
Analytical Method ◽  
Electromotive Force ◽  
Analytical Calculation ◽  
Air Gap ◽  
Permanent Magnet Machines ◽  
Peak Value

This paper presented a novel analytical method for calculating magnetic field in the slotted air gap of spoke-type permanent-magnet machines using conformal mapping. Firstly, flux density without slots and complex relative air-gap permeance of slotted air gap are derived from conformal transformation separately. Secondly, they are combined in order to obtain normalized flux density taking account into the slots effect. The finite element (FE) results confirmed the validity of the analytical method for predicting magnetic field and back electromotive force (BEMF) in the slotted air gap of spoke-type permanent-magnet machines. In comparison with FE result, the analytical solution yields higher peak value of cogging torque.

Performance analysis of magnetic gear with Halbach array for high power and high speed

2020 ◽  
Vol 64 (1-4) ◽  
pp. 959-967
Author(s):  
Se-Yeong Kim ◽  
Tae-Woo Lee ◽  
Yon-Do Chun ◽  
Do-Kwan Hong
Keyword(s):  
Permanent Magnet ◽  
Eddy Current ◽  
High Power ◽  
High Speed ◽  
Torque Ripple ◽  
Eddy Current Loss ◽  
Element Analysis ◽  
Current Loss ◽  
Halbach Array ◽  
Magnetic Gear

In this study, we propose a non-contact 80 kW, 60,000 rpm coaxial magnetic gear (CMG) model for high speed and high power applications. Two models with the same power but different radial and axial sizes were optimized using response surface methodology. Both models employed a Halbach array to increase torque. Also, an edge fillet was applied to the radial magnetized permanent magnet to reduce torque ripple, and an axial gap was applied to the permanent magnet with a radial gap to reduce eddy current loss. The models were analyzed using 2-D and 3-D finite element analysis. The torque, torque ripple and eddy current loss were compared in both models according to the materials used, including Sm2Co17, NdFeBs (N42SH, N48SH). Also, the structural stability of the pole piece structure was investigated by forced vibration analysis. Critical speed results from rotordynamics analysis are also presented.

Analysis of structure factors affecting suspension force of permanent magnet system with variable magnetic flux path control

2020 ◽  
Vol 64 (1-4) ◽  
pp. 1495-1504
Author(s):  
Fangchao Xu ◽  
Yongquan Guo ◽  
Ran Zhou ◽  
Junjie Jin ◽  
Chuan Zhao ◽  
...  
Keyword(s):  
Magnetic Flux ◽  
Permanent Magnet ◽  
System Structure ◽  
Magnet System ◽  
Load Torque ◽  
Factors Affecting ◽  
Annular Gap ◽  
Path Control ◽  
Structure Factors ◽  
Flux Path

To solve the problem of reduction of suspension force of permanent magnet system with variable magnetic flux path control, according to the structure of the system, suspension principle of the permanent magnet system with variable magnetic flux path control and the generation principle of the load torque, the influence of the mechanical structure of the system on the suspension force is analyzed by changing part of parameters of the system structure. The results show that the existence of magnetic isolation plate is the main reason for the decrease of suspension force, the permanent magnet ring can be thickened to 11.91 mm, the annular gap can be reduced to 1 mm, thickness of the “F” shaped magnetizer can be increased to 9 mm to increase the suspension force.

Influence of unbalanced magnetic force on shaft deflection in permanent magnet synchronous motor with fractional slot concentrated windings

2020 ◽  
Vol 64 (1-4) ◽  
pp. 1461-1468
Author(s):  
Ting Dong ◽  
Juyan Huang ◽  
Bing Peng ◽  
Ling Jian
Keyword(s):  
Permanent Magnet ◽  
Magnetic Force ◽  
Permanent Magnet Synchronous Motor ◽  
Operational Reliability ◽  
Topology Structure ◽  
Permanent Magnet Synchronous Motors ◽  
Synchronous Motors ◽  
Shaft Deflection ◽  
Large Length ◽  
Fractional Slot

The calculation accuracy of unbalanced magnetic forces (UMF) is very important to the design of rotor length, because it will effect the shaft deflection. But in some permanent magnet synchronous motors (PMSMs) with fractional slot concentrated windings (FSCW), the UMF caused by asymmetrical stator topology structure is not considered in the existing deflection calculation, which is very fatal for the operational reliability, especially for the PMSMs with the large length-diameter ratio, such as submersible PMSMs. Therefore, the part of UMF in the asymmetrical stator topology structure PMSMs caused by the choice of pole-slot combinations is analysized in this paper, and a more accurate rotor deflection calculation method is also proposed.

Study and design of dual stator permanent magnet machine with spoke-type configurations using phase-group concentrated-coil windings

2020 ◽  
Vol 64 (1-4) ◽  
pp. 1381-1389
Author(s):  
Dezhi Chen ◽  
Chengwu Diao ◽  
Zhiyu Feng ◽  
Shichong Zhang ◽  
Wenliang Zhao
Keyword(s):  
Permanent Magnet ◽  
Permanent Magnets ◽  
Low Cost ◽  
Dynamic Performance ◽  
Torque Ripple ◽  
Permanent Magnet Machine ◽  
Torque Density ◽  
Phase Group ◽  
High Torque ◽  
Simulation Results

In this paper, a novel dual-stator permanent magnet machine (DsPmSynM) with low cost and high torque density is designed. The winding part of the DsPmSynM adopts phase-group concentrated-coil windings, and the permanent magnets are arranged by spoke-type. Firstly, the winding structure reduces the amount of copper at the end of the winding. Secondly, the electromagnetic torque ripple of DsPmSynM is suppressed by reducing the cogging torque. Furthermore, the dynamic performance of DsPmSynM is studied. Finally, the experimental results are compared with the simulation results.

Analysis of magnetic force and dynamic characteristic for non-contact permanent magnet linear drive device

2020 ◽  
Vol 64 (1-4) ◽  
pp. 1337-1345
Author(s):  
Chuan Zhao ◽  
Feng Sun ◽  
Junjie Jin ◽  
Mingwei Bo ◽  
Fangchao Xu ◽  
...  
Keyword(s):  
Finite Element ◽  
Permanent Magnet ◽  
Dynamic Characteristic ◽  
Driving Force ◽  
Magnetic Circuit ◽  
Response Speed ◽  
Computation Method ◽  
Element Analysis ◽  
Element Simulation ◽  
The Relationship

This paper proposes a computation method using the equivalent magnetic circuit to analyze the driving force for the non-contact permanent magnet linear drive system. In this device, the magnetic driving force is related to the rotation angle of driving wheels. The relationship is verified by finite element analysis and measuring experiments. The result of finite element simulation is in good agreement with the model established by the equivalent magnetic circuit. Then experiments of displacement control are carried out to test the dynamic characteristic of this system. The controller of the system adopts the combination control of displacement and angle. The results indicate that the system has good performance in steady-state error and response speed, while the maximum overshoot needs to be reduced.

Sign in / Sign up

Export Citation Format

Share Document