scholarly journals Pengaruh jarak nozzle penyemprot terhadap kemampukerasan baja komersil dengan metode jominy test

2020 ◽  
Vol 9 (2) ◽  
Author(s):  
Yusuf Yusuf ◽  
Asep Ruchiyat ◽  
Muh Anhar
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Treatment Process ◽  
Test Method ◽  
Holding Time ◽  
Heat Treatment Process ◽  
Wear And Tear ◽  
Jominy Test ◽  
Specimen Number

Steel is the material most widely used in the industry. To avoid wear and tear on steel, it is necessary to do heat treatment to improve the mechanical properties of the steel according to its application in the field. The increase in hardenability in metals can be determined by doing a hardenability test, namely the Jominy test method. The Jominy test is a method to determine the hardness value of metal using ASTM standards. This research was conducted with varying the distance of the nozzle of the sprayer to the lower end of the specimen, namely 10 mm, 12.5 mm, and 14 mm with a long spraying time of 15 minutes. The heat treatment process at temperature of 780oC and 90 minutes holding time. The averagehardness value of specimen number one (10 mm spraying distance) is 45.43 kgf, specimen number two (12.5 mm spraying distance) is 45.68 kgf, and specimen number three (14 mm spraying distance) is 44.31 kgf. The highest hardness value was specimen number two, there was an increase of 1.87 kgf (4.02%), according to ASTM standards where the spraying distance was 12.5 mm.Keywords: Steel, spraying distance, Jominy test.

Effect of Heat Treatment on Microstructures and Mechanical Properties of A356 Alloy by Low Pressure Casting

2015 ◽  
Vol 1096 ◽  
pp. 319-324
Author(s):  
Xiao Jian Yu ◽  
Ya Lin Lu ◽  
Fu Xian Zhu ◽  
Xing Cheng Li
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Treatment Process ◽  
A356 Alloy ◽  
Low Pressure ◽  
Holding Time ◽  
Pressure Casting ◽  
Heat Treatment Process ◽  
Low Pressure Casting ◽  
Microstructures And Mechanical Properties

Automobile wheel of A356 alloy was cast by low pressure casting process. The effect of heat treatment process on microstructures and mechanical properties of A356 alloy cast was discussed. The results indicated that optimal parameters of heat treatment process for A356 alloy included solution temperature of 535°Cand holding time of 4.5hours, aging temperature of 145°Cand holding time of 4hours. Ultimate strength of A356 is 270MPa and elongation rate is 10%. Meanwhile, the microstructure has been apparently improved. The eutectic silicon particle became more spheroidal and distributed uniformly in matrix.

Study on Normalizing Process for 100mm E40 Heavy Plate

2013 ◽  
Vol 765-767 ◽  
pp. 197-201
Author(s):  
Xiang Yu Xu ◽  
Xue Min Wang
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Treatment Process ◽  
High Strength ◽  
Holding Time ◽  
Heat Treatment Process ◽  
Heavy Plate ◽  
Hull Steel ◽  
Normalization Process

The influence of chemical composition, heat treatment process and microstructure on the properties of E40 heavy plate have been studied. After normalization process of thick TMCP plate for high strength hull steel, the structure is substantially more regular, but the strength decreases. The former microstructure consists of lath-like bainite, but after heat treatment it consists of ferrite and pearlite. The mechanical properties meet the requirement of GB 712 prescript. With cooling rate decreasing, grain size in normalizing samples increases gradually, and the strength decreases. With the holding time extending, grain growth is not obvious, and the strength decreases. The best normalizing temperature is 910 °C, and the best holding time is about100 min.

Relationship of Microstructure and Mechanical Properties in Er-Containing Aluminum Alloy

2015 ◽  
Vol 1120-1121 ◽  
pp. 1109-1114
Author(s):  
Xin Lei ◽  
Hui Huang ◽  
S.P. Wen
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Aluminum Alloy ◽  
Treatment Process ◽  
Mg Alloys ◽  
The Other ◽  
Heat Treatment Process ◽  
Comprehensive Performance ◽  
Relationship Of ◽  
Al Mg Alloys

This study investigated the mechanical properties and microstructures of Er-containing Al–Mg alloys. The research found that the H114-T sheet of Er-containing Al–Mg alloys showed a relative good comprehensive performance in mechanical properties. With the special rolling and heat treatment process, this H114-T sheet showed different morphology of microstructures with the other sheets in Er-containing Al–Mg alloys. Grains in H114-T sheet performed irregular shape polygon, a number of subgrains appeared in grains, the amount of dislocations in grains decreased. H114-T sheet possessed a lot of Copper texture, this may be one of important factors influenced the mechanical properties.

Study of Cu Addition on Precipitation Behaviors and Mechanical Properties in AA6082 Al-Mg-Si Alloy

2007 ◽  
Vol 546-549 ◽  
pp. 825-828 ◽  
Author(s):  
Man Jin ◽  
Jing Li ◽  
Guang Jie Shao
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Thermal Stability ◽  
Treatment Process ◽  
Mechanical Tests ◽  
Age Hardening ◽  
Heat Treatment Process ◽  
Softening Process

The precipitation behaviors and microstructures of nano-precipitates in AA6082 Al-Mg-Si alloy with and without Cu additions during heat treatment process were studied using hardness measurements, TEM, mechanical tests and 3DAP. Meanwhile, the softening process of 6082 alloys with Cu and without Cu, isothermally conditioned at 250°C, has also been investigated. It was found that the rate of age hardening, mechanical properties and thermal stability are higher for the Cu-containing alloy. The TEM and 3DAP observations showed that Q’ precipitates were existed after aged at 170°C for 8h in the alloy with Cu addition. Comparing the hardness, mechanical properties and thermal stability curves, it was concluded that the Q’ precipitates play a major role in improving the age hardening kinetics and properties of 6082 alloy with Cu addition.

Effect of Heat Treatment Process on Mechanical Properties and Microstructure of S280

2021 ◽  
Vol 1035 ◽  
pp. 344-349
Author(s):  
Ye Qin Zhang ◽  
Ping Zhong ◽  
Huan Feng Li ◽  
Wen Qiang Zhang
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Treatment Process ◽  
Lath Martensite ◽  
Solution Temperature ◽  
Heat Treatment Process ◽  
Strengthening Phase ◽  
Optimal Heat Treatment ◽  
Precipitate Strengthening ◽  
Temperature Heating

The effect of solution temperature and aging temperature on mechanical properties and microstructure of the new ultrahigh strength stainless steel S280 was investigated by heat treatment process experiment. The results showed that the optimal heat treatment process was as follows: heating to 1080 °C，holding for a hour, and quenching in oil; cooling to -73 °C, holding for 2 hour, and warming in air to room temperature; heating to 540~550 °C, holding for 4 hour, and cooling in air. Choosing this heat treatment process, the steel can get good coordination between strength and toughness. Analyzed by HREM, the steel had desirable microstructures, which were fine lath martensite matrix with high density dislocation and finely dispersed precipitate strengthening phase, and film-like reversed austenite precipitated from the boundary of martensite.

scholarly journals Heat Treatment Effect on Mechanical Properties of 3D Printed Polymers

2019 ◽  
Vol 264 ◽  
pp. 02001 ◽  
Author(s):  
Eduardo de Avila ◽  
Jaeseok Eo ◽  
Jihye Kim ◽  
Namsoo P. Kim
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Treatment Effect ◽  
Biomedical Applications ◽  
Treatment Process ◽  
Heat Treatment Process ◽  
Post Heat Treatment ◽  
Intraocular Surgery ◽  
Osteoinductive Potential ◽  
3D Printed

PMMA, PC, and PEEK are thermoplastic polymers that possess favorable properties for biomedical applications. These polymers have been used in fields of maxillo-facial, orthopedic, intraocular surgery, and bio-implant, due to their excellent mechanical properties, osteoinductive potential, and antimicrobial capabilities. In this study, the effect of heat treatment on the mechanical properties of 3D printed polymers was characterized. By modifying printing temperature and post heat treatment process, the mechanical properties were specifically tailored for different applications, correlating with the properties of the implants that are commonly made using molding processes.

The influence of heat treatment process on mechanical properties of surface treated volcanic ash particles/polyphenylene sulfide composites

2016 ◽  
Vol 39 (5) ◽  
pp. 1604-1611 ◽  
Author(s):  
Mustafa Özgür Bora ◽  
Onur Çoban ◽  
Togayhan Kutluk ◽  
Sinan Fidan ◽  
Tamer Sinmazçe˙lk
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Volcanic Ash ◽  
Treatment Process ◽  
Polyphenylene Sulfide ◽  
Heat Treatment Process

Numerical Simulation of the H-Beam during Cooling Process

2013 ◽  
Vol 310 ◽  
pp. 145-149 ◽  
Author(s):  
Jian Liu ◽  
Fu Zeng Hou ◽  
Xiao Guang Yu
Keyword(s):  
Mechanical Properties ◽  
Numerical Simulation ◽  
Heat Treatment ◽  
Theoretical Basis ◽  
Treatment Process ◽  
Residual Austenite ◽  
Heat Treatment Process ◽  
Cooling Process ◽  
Controlled Cooling ◽  
H Beam

In order to improve the comprehensive mechanical properties of the steel, the heat treatment software COSMAP is used to simulate the rolling and controlled cooling of H-beam. The numerical simulation shows that the mechanical properties of controlled cooling can be obviously improved, when the cooling rate is controlled at 10°C/s around. Strength and hardness can be improved under the condition of ductility and toughness ensured. Meanwhile the amount of residual austenite can be reduced significantly. It provides a theoretical basis for further optimization of the heat treatment process.

Optimization for Heat Treatment Process of Supercritical Material F92Steel

2011 ◽  
Vol 142 ◽  
pp. 95-98
Author(s):  
Jian Sheng Ding ◽  
Lin Xun Liu ◽  
Jin Chun Feng
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
High Temperature ◽  
Treatment Process ◽  
Rupture Strength ◽  
Lath Martensite ◽  
Precipitation Strengthening ◽  
Heat Treatment Process ◽  
Fully Integrated ◽  
Quenching And Tempering

The supercritical material F92 steel is regarded as the research object, and the influence law of heat treatment process on its tissue and properties is analyzed. The results show that when the temperature of heat treatment quenching and tempering is too low, a large number of alloying elements cannot be fully integrated into the austenite, and the optimal obdurability of F92 steel is still not fully exploited; while too high temperature of heat treatment quenching and tempering will weaken the strength, plasticity and toughness. When F92 steel is processed by heating quenching at 1050 °C and tempering at 680 °C, its tissue is the smaller tempered lath martensite. The carbide is precipitated, generating precipitation strengthening, which gives it a high rupture strength and toughness. F92 steel is with high mechanical properties when heating quenched at 1050 °C and tempered 680 °C.

Effect of Heat Treatment Process on the Preparation of Foamed Glass Ceramic from Red Mud and Fly Ash

2014 ◽  
Vol 670-671 ◽  
pp. 201-204 ◽  
Author(s):  
Yu Xi Guo ◽  
Yi He Zhang ◽  
Hong Wei Huang ◽  
Pan Hu
Keyword(s):  
Heat Treatment ◽  
Fly Ash ◽  
Glass Ceramic ◽  
Red Mud ◽  
Treatment Process ◽  
Sintering Temperature ◽  
Holding Time ◽  
Heat Treatment Process ◽  
Ceramic Foams

Lightweight glass ceramic foams have been prepared from a mixture of solid wastes, namely 40 wt-% red mud and 60 wt-% fly ash. In this work, we illustrate the effects of variables in heat treatment process, including the sintering temperature and the holding time, on the quality of the foams. The reduction of sintering temperature as well as the holding time, was found to limit the coalescence and improve the apparent density and the compressive strength.

Sign in / Sign up

Export Citation Format

Share Document