scholarly journals Heat transfer intensification of Zirconia/water nanofluid

2017 ◽  
Vol 13 ◽  
pp. 01-08
Author(s):  
Mohamed Iqbal Shajahan ◽  
Chockalingam Sundar Raj ◽  
Sambandan Arul ◽  
Palanisamy Rathnakumar
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Laminar Flow ◽  
Friction Factor ◽  
Volume Concentration ◽  
Constant Heat Flux ◽  
Particle Volume ◽  
Heat Transfer Intensification ◽  
Nusselt Numbers ◽  
Thermal Analyser

This paper investigated convective heat transfer and friction factor of ZrO2/H2O nanofluid through a circular pipe under laminar flow condition with constant heat flux. Nanofluid is prepared for 0.5, 0.75 and 1% volume concentrations with yttrium oxide surfactant. Nanofluid’s thermal conductivity and viscosity is measured by KD2 Pro thermal analyser and Brookfield viscometer respectively. Results showed that the thermal conductivity and viscosity increased with increase in particle volume concentration. These nanofluids are experimented in a forced convection system, first heat transfer characteristics of DI (Deionised) water  under laminar flow in a copper tube measured, then three nanofluids are carried out the tests, results revealed that the enhanced Nusselt numbers of 21.09,28.05 and 35.73%  at the 0.5, 0.75 and 1% volume concentrations, There is no excess penalty in pumping power  and results showed  less variations in friction factor for nanofluids comparatively with the base fluid DIWater.

scholarly journals Thermal Efficiency, Heat Transfer, and Friction Factor Analyses of MWCNT + Fe3O4/Water Hybrid Nanofluids in a Solar Flat Plate Collector under Thermosyphon Condition

Processes ◽  
2021 ◽  
Vol 9 (1) ◽  
pp. 180 ◽  
Author(s):  
Bahaa Saleh ◽  
Lingala Syam Sundar
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Carbon Nanotubes ◽  
Friction Factor ◽  
Thermal Efficiency ◽  
Volume Concentration ◽  
Multi Walled Carbon Nanotubes ◽  
Hybrid Nanofluids ◽  
Flat Plate Collector ◽  
Walled Carbon Nanotubes

The heat transfer, friction factor, and collector efficiency are estimated experimentally for multi-walled carbon nanotubes+Fe3O4 hybrid nanofluid flows in a solar flat plate collector under thermosyphon circulation. The combined technique of in-situ growth and chemical coprecipitation was utilized to synthesize the multi-walled carbon nanotubes+Fe3O4 hybrid nanoparticles. The experiments were carried out at volume flow rates from 0.1 to 0.75 L/min and various concentrations from 0.05% to 0.3%. The viscosity and thermal conductivity of the hybrid nanofluids were experimentally measured at different temperatures and concentrations. Due to the improved thermophysical properties of the hybrid nanofluids, the collector achieved better thermal efficiency. Results show that the maximum thermal conductivity and viscosity enhancements are 28.46% and 50.4% at 0.3% volume concentration and 60 °C compared to water data. The Nusselt number, heat transfer coefficient, and friction factor are augmented by 18.68%, 39.22%, and 18.91% at 0.3% volume concentration and 60 °C over water data at the maximum solar radiation. The collector thermal efficiency improved by 28.09% at 0.3 vol. % at 13:00 h daytime and a Reynolds number of 1413 over water data. Empirical correlations were developed for friction factor and Nusselt number.

Pressure Drop and Heat Transfer of Nanofluid in Turbulent Pipe Flow Considering Particle Coagulation and Breakage

2014 ◽  
Vol 136 (11) ◽  
Author(s):  
Jian-Zhong Lin ◽  
Yi Xia ◽  
Xiao-Ke Ku
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Friction Factor ◽  
Pipe Flow ◽  
Volume Concentration ◽  
Particle Diameter ◽  
Turbulent Pipe Flow ◽  
Particle Volume ◽  
Friction Factors

Numerical simulations of Al2O3/water nanofluid in turbulent pipe flow are performed with considering the particle convection, diffusion, coagulation, and breakage. The distributions of particle volume concentration, the friction factor, and heat transfer characteristics are obtained. The results show that the initial uniform distributions of particle volume concentration become nonuniform, and increase from the pipe wall to the center. The nonuniformity becomes significant along the flow direction from the entrance and attains a steady state gradually. Friction factors increase with the increase of particle volume concentrations and particle diameter, and with the decrease of Reynolds number. The friction factors increase remarkably at lower volume concentration, while slightly at higher volume concentration. The presence of nanoparticles provides higher heat transfer than pure water. The Nusselt number of nanofluids increases with increasing Reynolds number, particle volume concentration, and particle diameter. The rate increase in Nusselt number at lower particle volume concentration is more than that at higher concentration. For a fixed particle volume concentration, the friction factor is smaller while the Nusselt number is larger for the case with uniform distribution of particle volume concentration than that with nonuniform distribution. In order to effectively enhance the heat transfer using nanofluid and simultaneously save energy, it is necessary to make the particle distribution more uniform. Finally, the expressions of friction factor and Nusselt number as a function of particle volume concentration, particle diameter and Reynolds number are derived based on the numerical data.

Investigation of the convective heat transfer and friction factor of magnetic Ni nanofluids within cylindrical pipes

2021 ◽  
Vol 8 (1) ◽  
Author(s):  
M. Abdelkader ◽  
H. Ameur ◽  
Y. Menni
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Friction Factor ◽  
Turbulent Flows ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Constant Heat Flux ◽  
Particle Volume ◽  
Number Range

The current paper reports the results of numerical research on the magnetic Ni nanofluid flowing in a tube, developing turbulent flows under constant heat flux conditions. The numerical investigations are conducted for a Reynolds number range from 3,000 to 22,000, and a particle concentration range of 0% to 0.6%. The effects of the Reynolds number on the friction factor and Nusselt number are computed and compared satisfactorily with the experimental results of the literature. The classical correlations of Gnielinski, Notter – Rouse, and Pak and Cho are verified by predicting the Nusselt number of the Ni nanofluid. The obtained results revealed an enhancement in the heat transfer with the increase of magnetic Ni particle volume fraction and Reynolds number.

HEAT TRANSFER ENHANCEMENT IN A HELICALLY COILED TUBE WITH Al2O3/WATER NANOFLUID UNDER LAMINAR FLOW CONDITION

2012 ◽  
Vol 11 (05) ◽  
pp. 1250029 ◽  
Author(s):  
P. C. MUKESH KUMAR ◽  
J. KUMAR ◽  
S. SURESH ◽  
K. PRAVEEN BABU
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Laminar Flow ◽  
Transfer Coefficient ◽  
Flow Condition ◽  
Volume Concentration ◽  
Dean Number ◽  
Particle Volume ◽  
Coiled Tube ◽  
Helically Coiled Tube

In this experimental investigation, the heat transfer coefficients of a shell and helically coiled tube heat exchanger using Al2O3 /water nanofluid under laminar flow condition were studied. The Al2O3 nanoparticles were characterized by X-Ray diffraction (XRD). The Al2O3 /water nanofluid at 0.1%, 0.4% and 0.8% particle volume concentration were prepared by using two step method. The prepared nanofluid was characterized by scanning electron microscope (SEM). It is observed that the overall heat transfer coefficient, inner heat transfer coefficient and experimental inner Nusselt number increase while increasing particle volume concentration and increasing inner Dean number. The enhancement of overall heat transfer coefficient was found to be 7%, 16.9% and 24.2% at 0.1%, 0.4% and 0.8% Al2O3 /water nanofluid respectively when compared with water. The enhancement of tube side experimental Nusselt number was found to be 17%, 22.9% and 28% at 0.1%, 0.4% and 0.8% particle volume concentration of Al2O3 /water nanofluid respectively when compared with water at fixed Dean number. The tests were conducted in the range of 1600 < De < 2700, and 5200 < Re < 8600 under laminar flow condition and counter flow configuration. These enhancements are due to higher thermal conductivity of nanofluid while increasing particle volume concentration and Brownian motion of nanoparticles. It is studied that there is no negative impact on formation of secondary flow and mixing of fluid when nanofluid passes through the helically coiled tube.

Heat Transfer in a Surfactant Drag-Reducing Solution—A Comparison With Predictions for Laminar Flow

2005 ◽  
Vol 128 (6) ◽  
pp. 557-563 ◽  
Author(s):  
Paul L. Sears ◽  
Libing Yang
Keyword(s):  
Heat Transfer ◽  
Laminar Flow ◽  
Reynolds Numbers ◽  
High Heat ◽  
High Heat Flux ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Nusselt Numbers ◽  
Drag Reducing Additive ◽  
Good Agreement

Heat transfer coefficients were measured for a solution of surfactant drag-reducing additive in the entrance region of a uniformly heated horizontal cylindrical pipe with Reynolds numbers from 25,000 to 140,000 and temperatures from 30to70°C. In the absence of circumferential buoyancy effects, the measured Nusselt numbers were found to be in good agreement with theoretical results for laminar flow. Buoyancy effects, manifested as substantially higher Nusselt numbers, were seen in experiments carried out at high heat flux.

Heat Transfer Performance of Different Nanofluids Flows in a Helically Coiled Heat Exchanger

2013 ◽  
Vol 832 ◽  
pp. 160-165 ◽  
Author(s):  
Mohammad Alam Khairul ◽  
Rahman Saidur ◽  
Altab Hossain ◽  
Mohammad Abdul Alim ◽  
Islam Mohammed Mahbubul
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Friction Factor ◽  
Heat Exchangers ◽  
Heat Transfer Performance ◽  
Volume Concentration ◽  
Transfer Performance

Helically coiled heat exchangers are globally used in various industrial applications for their high heat transfer performance and compact size. Nanofluids can provide excellent thermal performance of this type of heat exchangers. In the present study, the effect of different nanofluids on the heat transfer performance in a helically coiled heat exchanger is examined. Four different types of nanofluids CuO/water, Al2O3/water, SiO2/water, and ZnO/water with volume fractions 1 vol.% to 4 vol.% was used throughout this analysis and volume flow rate was remained constant at 3 LPM. Results show that the heat transfer coefficient is high for higher particle volume concentration of CuO/water, Al2O3/water and ZnO/water nanofluids, while the values of the friction factor and pressure drop significantly increase with the increase of nanoparticle volume concentration. On the contrary, low heat transfer coefficient was found in higher concentration of SiO2/water nanofluids. The highest enhancement of heat transfer coefficient and lowest friction factor occurred for CuO/water nanofluids among the four nanofluids. However, highest friction factor and lowest heat transfer coefficient were found for SiO2/water nanofluids. The results reveal that, CuO/water nanofluids indicate significant heat transfer performance for helically coiled heat exchanger systems though this nanofluids exhibits higher pressure drop.

scholarly journals Experimental Investigation of Thermo-Physical Properties of Tri-Hybrid Nanoparticles in Water-Ethylene Glycol Mixture

2021 ◽  
Vol 18 (8) ◽  
Author(s):  
Anwar Ilmar RAMADHAN ◽  
Wan Hamzah AZMI ◽  
Rizalman MAMAT
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Ethylene Glycol ◽  
Physical Properties ◽  
Dynamic Viscosity ◽  
Volume Concentration ◽  
Hybrid Nanoparticles ◽  
Maximum Enhancement ◽  
Hybrid Nanofluids ◽  
Thermo Physical Properties

In recent years, research has focused on enhancing the thermo-physical properties of a single component nanofluid. Therefore, hybrid or composite nanofluids have been developed to improve heat transfer performance. The thermo-physical properties of the Al2O3-TiO2-SiO2 nanoparticles suspended in a base of water (W) and ethylene glycol (EG) at constant volume ratio of 60:40 and different volume concentrations were investigated. The experiment was conducted for the volume concentrations of 0.05, 0.1, 0.2, and 0.3% of Al2O3-TiO2-SiO2 nanofluids at different temperatures of 30, 40, 50, 60, and 70 °C. Thermal conductivity and dynamic viscosity measurements were carried out at temperatures ranging from 30 to 70 °C by using KD2 Pro Thermal Properties Analyzer and Brookfield LVDV III Ultra Rheometer, respectively. The highest thermal conductivity for tri-hybrid nanofluids was obtained at 0.3% volume concentration, and the maximum enhancement was increased up to 9% higher than the base fluid (EG/W). Tri-hybrid nanofluids with a volume concentration of 0.05% gave the lowest effective thermal conductivity of 4.8 % at 70 °C temperature. Meanwhile, the dynamic viscosity of the tri-hybrid nanofluids was influenced by volume concentration and temperature. Furthermore, tri-hybrid nanofluids behaved as a Newtonian fluid for volume concentrations from 0.05 to 3.0%. The properties enhancement ratio (PER) estimated that the tri-hybrid nanofluids will aid in heat transfer for all samples in the present. The new correlations for thermal conductivity and dynamic viscosity of tri-hybrid nanofluids were developed with minimum deviation. As a conclusion, the combination of the enhancement in thermal conductivity and dynamic viscosity for tri-hybrid at 0.3% volume concentration was found the optimum condition with more advantage for heat transfer than other concentrations.

An Evaluation of the Application of Nanofluids in Intercooled Cycle Marine Gas Turbine Intercooler

2015 ◽  
Vol 138 (1) ◽  
Author(s):  
Ningbo Zhao ◽  
Xueyou Wen ◽  
Shuying Li
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Gas Turbine ◽  
Heat Transfer Performance ◽  
Volume Concentration ◽  
Inlet Temperature ◽  
Transfer Performance ◽  
Pumping Power ◽  
Flow And Heat Transfer ◽  
Overall Performance

Coolant is one of the important factors affecting the overall performance of the intercooler for the intercooled (IC) cycle marine gas turbine. Conventional coolants, such as water and ethylene glycol, have lower thermal conductivity which can hinder the development of highly effective compact intercooler. Nanofluids that consist of nanoparticles and base fluids have superior properties like extensively higher thermal conductivity and heat transfer performance compared to those of base fluids. This paper focuses on the application of two different water-based nanofluids containing aluminum oxide (Al2O3) and copper (Cu) nanoparticles in IC cycle marine gas turbine intercooler. The effectiveness-number of transfer unit method is used to evaluate the flow and heat transfer performance of intercooler, and the thermophysical properties of nanofluids are obtained from literature. Then, the effects of some important parameters, such as nanoparticle volume concentration, coolant Reynolds number, coolant inlet temperature, and gas side operating parameters on the flow and heat transfer performance of intercooler, are discussed in detail. The results demonstrate that nanofluids have excellent heat transfer performance and need lower pumping power in comparison with base fluids under different gas turbine operating conditions. Under the same heat transfer, Cu–water nanofluids can reduce more pumping power than Al2O3–water nanofluids. It is also concluded that the overall performance of intercooler can be enhanced when increasing the nanoparticle volume concentration and coolant Reynolds number and decreasing the coolant inlet temperature.

scholarly journals The Effect of Nanofluid Volume Concentration on Heat Transfer and Friction Factor inside a Horizontal Tube

2013 ◽  
Vol 2013 ◽  
pp. 1-12 ◽  
Author(s):  
Adnan M. Hussein ◽  
K. V. Sharma ◽  
R. A. Bakar ◽  
K. Kadirgama
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Thermal Properties ◽  
Friction Factor ◽  
Volume Concentration ◽  
Convection Heat Transfer ◽  
Horizontal Tube ◽  
Maximum Deviation ◽  
Flat Tube

The additives of solid nanoparticles to liquids are significant enhancement of heat transfer and hydrodynamic flow. In this study, the thermal properties of three types of nanoparticles (Al2O3, TiO2, and SiO2) dispersed in water as a base fluid were measured experimentally. Forced convection heat transfer turbulent flow inside heated flat tube was numerically simulated. The heat flux around flat tube is 5000 W/m2and Reynolds number is in the range of5×103to50×103. CFD model by finite volume method used commercial software to find hydrodynamic and heat transfer coefficient. Simulation study concluded that the thermal properties measured and Reynolds number as input and friction factor and Nusselt number as output parameters. Data measured showed that thermal conductivity and viscosity increase with increasing the volume concentration of nanofluids with maximum deviation 19% and 6%, respectively. Simulation results concluded that the friction factor and Nusselt number increase with increasing the volume concentration. On the other hand, the flat tube enhances heat transfer and decreases pressure drop by 6% and −4%, respectively, as compared with circular tube. Comparison of numerical analysis with experimental data available showed good agreement with deviation not more than 2%.

Effects of Dented Roughness on Laminar Flow and Heat Transfer in Microchannels

2010 ◽  
Author(s):  
Hui Miao ◽  
Yong Huang ◽  
Fa Xie ◽  
Haigang Chen ◽  
Fang Wang
Keyword(s):  
Heat Transfer ◽  
Laminar Flow ◽  
Working Fluid ◽  
Heat Transfer Characteristics ◽  
Nusselt Numbers ◽  
Flow And Heat Transfer ◽  
Micro Channels ◽  
Planar Area ◽  
Poiseuille Number ◽  
Energy Equations

Liquid laminar flow and heat transfer characteristics for parallel plate micro-channels consisting of many triangle shape hollows to fit with the etching surfaces are investigated numerically in the present paper. The height of the channel is 50μm, with three different relative depths, three relative spacing, and three oblique angles of the triangle surface, respectively. The 2D N-S and energy equations are solved using a commercial CFD code FLUENT6.3. Water is used as the working fluid, and the Reynolds number ranges from 100 to 1500. The global Poiseuille number and average Nusselt number are obtained. It is shown that the dented shapes cause a modest influence in Poiseuille number, but a greater impact on the Nusselt numbers. In addition, both of Po and Nu increase modestly with Re. The local Nusselt numbers are always lower in dented area and larger in planar area of dented roughness microchannels, than that of conventional smooth value. Finally, geometry parameters have modest impact on heat transfer for dented roughness.

Sign in / Sign up

Export Citation Format

Share Document